change wheel RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Workshop Manual

13B-312V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 2
"MINUS"
Status ET703 becomes DECREASE when the - button of the cruise control/speed
limiter is pressed. This button is on the steering wheel, on the left-hand side.
If status ET703 does not change to MINUS, check the condition of the cruise control/
speed limiter +/- button, and the condition of its connector. Repair if necessary.
To perform these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR Mechanical, 88C,
Airbag and pretensioners, Driver's front airbag: Removal - Refitting).
Measure the resistance of the following connections while pressing the - button
(on the button connections):
•86G of component 331,
•86M of component 331.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the resistance is not approximately 100 Ω check the continuity of the connection
when the button is not pressed.
If there is continuity, replace the +/- control button.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-313V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 3
"SUSPEND"
Status ET703 becomes SUSPEND when the cruise control / speed limiter 0 button is
pressed. This button is located on the steering wheel, to the right.
If status ET703 does not change to SUSPEND, check the condition of the cruise
control / speed limiter R/0 button, and the condition of its connector.
To perform these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR Mechanical, 88C,
Airbag and pretensioners, Driver's front airbag: Removal - Refitting).
Measure the resistance of the following connections while pressing the 0 button
(on the button connections):
•86G of component 331,
•86M of component 331.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the resistance is not approximately 0 Ω, replace the R/0 control button.
If there is continuity, replace the R/0 control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-314V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 4
"REACTIVATE"
Status ET703 becomes RESUME when the R button of the cruise control/speed
limiter is pressed. This button is located on the steering wheel, to the right.
If status ET703 does not change to RESUME, check the status of the cruise control/
speed limiter R/0 button, and the status of its connector. Repair if necessary.
To perform these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR Mechanical, 88C,
Airbag and pretensioners, Driver's front airbag: Removal - Refitting).
Measure the resistance of the following connections while pressing the R button
(on the button connections):
•86G of component 331,
•86M of component 331.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the resistance is not approximately 900 Ω, check the continuity of the connection
when the button is not pressed.
If there is continuity, replace the R/0 control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74