key RENAULT SCENIC 2013 J95 / 3.G Electronic Parking Brake Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2013, Model line: SCENIC, Model: RENAULT SCENIC 2013 J95 / 3.GPages: 115, PDF Size: 0.64 MB
Page 3 of 115
37B-3
MR-372-J84-37B000$072.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Introduction
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
Only affects the Scénic II phase 1 and the Scénic II phase 2:
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed).
Proceed as follows:
– Renault card in the card reader (keyless vehicle scenario 1, entry-level, without hands-free and scenario 2, top of
the range, hands-free),
– press and hold the Start button (longer than 5 seconds) with start-up conditions not fulfilled,
– connect the diagnostic tool and perform the required operations.
To cut off + after ignition feed, proceed as follows:
– disconnect the diagnostic tool,
– press the Start button twice briefly (less than 3 seconds).
– ensure that the + after ignition feed has been cut off by checking that the computer indicator lights on the
instrument panel have gone out.
Fault context.
Affects VDiag 08, 0C, 0D and 11.
Explanation of the fault context counters.
The are three different counters:
PR022: Dating counter
PR018: Presence counter
PR019: Frequency counter
Dating counter:The counter starts when the fault appears.
Each time the computer switches on and the fault is stored or present, the
counter increases by 1 up to 255.
Presence counter:As soon as the fault is present, the counter goes to 15. If the fault becomes
stored, each time the computer switches on, the number decreases by 1
(from 15 to 0) and goes back to 15 again if the fault reappears.
Frequency counter:Number of times the present fault appears; it sets to 0 when the fault appears.
It increases each time the fault moves from stored to present.
The maximum value of this counter is 15.
Page 14 of 115
37B-14
MR-372-J84-37B000$288.mif
V11
FPA
Vdiag No.: 0C, 04, 08,
0D, 11ELECTRONIC PARKING BRAKE
Fault finding – Replacement of components37B
B/ COMMISSIONING A NEW COMPUTER
1/ COMPUTER CONFIGURATION
– Carry out configuration in accordance with the customer's request (see Configurations and
programming).
2/ VEHICLE IDENTIFICATION NUMBER ENTRY
– run command VP004 Write VIN.
– enter the vehicle identification number using the diagnostic tool keypad,
–confirm.
3/ COMPUTER CALIBRATION AND COMMISSIONING
–In + after ignition feed, run command VP011 Computer calibration and initialisation and carry out
the following 4 steps.
STEP 1 VEHICLE MASS CALIBRATION
Screen 1:
With the dropdown menu, enter the following information:
– vehicle type,
– engine type,
– gearbox type,
– type of driving style,
– equipment level (for Vdiag 04),
– confirm the operation by pressing Next.
Screen 2:
– reread the highlighted information.
– If the highlighted information does not match the vehicle, return to the selection screen by pressing Back,
– if the highlighted information is correct, continue with step 2 by pressing Next.
STAGE 2 INITIALISING A NEW PARKING BRAKE
– Initialise the brake by pressing YES (you should hear a noise as the brake is applied and then released).
– Proceed to step 3 by pressing Next.
STEP 3 SLOPE INITIALISATION
– Calibrate the slope sensor by pressing Confirm. Proceed to step 4 by pressing Next.
STEP 4 INITIALISING ASSISTED BRAKING
– Carry out initialisation by pressing Confirm.
– Return to the selection list screen by pressing Finish. Note:
If the vehicle identification number is not entered and command CF007 Vehicle configuration is not run, step 3
of initialising the computer will not work.
WARNING
To initialise the computer, the vehicle must be on a horizontal surface with the brake cables correctly fitted
(connected to the rear brake callipers) and nobody must be working on the vehicle.