dashboard RENAULT TWINGO 2009 2.G Air Conditioning Owner's Manual

61A-51
HEATING
Heater matrix: Removal - Refitting
RIGHT-HAND DRIVE
61A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the bolt (6) from the heater matrix pipe bracket on
the distribution unit,
-the heater matrix pipe bracket on the distribution
unit,
-the bolt (7) from the heater matrix pipe bracket.
-the heater matrix pipe bracket,
-the heater matrix bolts (8) .
aPut a container in place to recover the coolant.
aRemove the heater matrix and its pipes.
aUnclip the pipe bracket.
aRemove the heater matrix pipes.
REFITTING
I - REMOVAL PREPARATION OPERATION
aAlways replace the seals between the pipes and the
heater matrix.II - REFITTING OPERATION FOR PART
CONCERNED
aFit the pipes on the heater matrix with new seals.
aClip on the pipe bracket.
aRefit the heater matrix and its pipes.
aRefit:
-the heater matrix bolts,
-the heater matrix pipe bracket,
-the bolt on the heater matrix pipe bracket,
-the heater matrix pipe bracket on the distribution
unit,
-the heater matrix pipe bracket bolt on the distribu-
tion unit.
III - FINAL OPERATION
aRemove the protective cover on the floor carpet.
aRefit:
-the dashboard (see Dashboard: Removal - Refit-
ting) (57A, Interior equipment),
-the central console (see Centre console: Remov-
al - Refitting) (57A, Interior equipment).
aRefit the storage compartment.
aRefit the radio (see Radio: Removal - Refitting)
(86A, Radio).
aRefit the tweeters (see Tweeter: Removal - Refit-
ting) (86A, Radio).
aRefit:
-the control panel (see 61A, Heating, Control pan-
el: Removal - Refitting, page 61A-65) ,
119704
WARNING
To avoid any leaks, check that the pipe surface is
sound before positioning the new seal. The sur-
face must be clean and scratch free.
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or RADIO
NO. 01 or RADIO NO. 03

61A-55
HEATING
Fan assembly: Removal - Refitting
RIGHT-HAND DRIVE
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (MR 411, 88C, Airbags
and pretensioners),
-the steering wheel (see Steering wheel: Removal
- Refitting) (MR 411, 36B, Power-assisted steer-
ing),
-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (MR 411, 84A, Control - Signals),
-the passenger's front airbag (see Passenger's
frontal airbag: Removal - Refitting) (MR 411,
88C, Airbags and seat belt pretensioners),
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (MR 411, 83A, Instrument pan-
el),
-the control panel (see 61A, Heating, Control pan-
el: Removal - Refitting, page 61A-65) .
aRemove the tweeter speakers (see Tweeter: Re-
moval - Refitting) (MR 411, 86A, Radio).
aRemove the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).aRemove the glovebox.
aRemove:
-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
-the dashboard (see Dashboard: Removal - Refit-
ting) (MR 412, 57A, Interior equipment).
II - REMOVAL OPERATION FOR PART
CONCERNED
aUnclip the fan assembly wiring (1) .
aUnclip the blower unit connector (2) .
aLift the blower unit connector.
aDisconnect the blower unit connector. Equipment required
Diagnostic tool
WITH 2 SPEAKERS, WITHOUT RADIO or RADIO
NO. 01 or RADIO NO. 03
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
124107

61A-56
HEATING
Fan assembly: Removal - Refitting
RIGHT-HAND DRIVE
61A
aPress on the blower unit tab (3) .
aTurn the blower unit a quarter of a turn clockwise.
aRemove the blower unit (4) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the blower unit.
aPress on the blower unit tab.
aTurn the blower unit a quarter of a turn anti-clock-
wise.
aCheck that the blower unit is in place.
aConnect the blower unit connector.
aClip on the blower unit connector.
aClip on the fan assembly connector wiring.
II - FINAL OPERATION.
aRefit:
-the dashboard (see Dashboard: Removal - Refit-
ting) (MR 412, 57A, Interior equipment),
-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment).aRefit the glovebox.
aRefit the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aRefit the tweeter speakers (see Tweeter: Removal
- Refitting) (MR 411, 86A, Radio).
aRefit:
-the control panel (see 61A, Heating, Control pan-
el: Removal - Refitting, page 61A-65) ,
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (MR 411, 83A, Instrument pan-
el),
-the passenger's front airbag (see Passenger's
frontal airbag: Removal - Refitting) (MR 411,
88C, Airbags and seat belt pretensioners),
-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (MR 411, 84A, Control - Signals),
-the steering wheel (see Steering wheel: Removal
- Refitting) (MR 411, 36B, Power-assisted steer-
ing),
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (MR 411, 88C, Airbags
and seat belt pretensioners).
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and pretensioners).
124108
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or RADIO
NO. 01 or RADIO NO. 03

61A-57
HEATING
Heating resistors: Removal - Refitting
LEFT-HAND DRIVE
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the centre console (see Centre console:
Removal - Refitting) (MR 412, 57A, Interior equip-
ment).
aRemove the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aUnclip the glovebox.
aRemove the dashboard lower trim (see Centre front
panel: Removal - Refitting) (MR 412, 57A, Interior
equipment).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector (1) from the heating resis-
tor.
aRemove:
-the heating resistor bolts (2) ,
-the heating resistor.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the heating resistor,
-the heating resistor bolts.
aConnect the heating resistor connector.
II - FINAL OPERATION.
aRefit the dashboard lower trim (see Centre front
panel: Removal - Refitting) (MR 412, 57A, Interior
equipment).
aClip the glovebox in position.
aRefit the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aRefit the centre console (see Centre console: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment). RADIO NO. 01 or RADIO NO. 03
VEHICLE WITHOUT RADIO
121468
VEHICLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03

61A-58
HEATING
Passenger compartment fan assembly control unit: Removal - Refitting
LEFT-HAND DRIVE
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of compo-
nents)(MR 413, 88C, Airbags and seat belt preten-
sioners).
aDisconnect the battery (see ) (MR 411, 80A, Bat-
tery).
aUnclip the upper storage compartment (1) on the
driver's side using the (Car. 1363).
aRemove:
-the passenger's front airbag (see Passenger's
frontal airbag: Removal - Refitting) (MR 411,
88C, Airbags and pretensioners),
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (MR 411, 83A, Instrument pan-
el).aUnclip the "trim - air vent" assembly (2) .
aDisconnect the hazard warning lights switch connec-
tor.
aUnclip:
-the fuse access flap (3) ,
-the dashboard lower trim. Special tooling required
Car. 1363Set of tr im removal levers.
Equipment required
Diagnostic tool
AIR CONDITIONING or STANDARD HEATING
119502
119518
119506

61A-59
HEATING
Passenger compartment fan assembly control unit: Removal - Refitting
LEFT-HAND DRIVE
61A
aDisconnect the connectors from the lower trim on
the dashboard (4) .
aRemove:
-the steering wheel lower cover bolt,
-the steering wheel lower cover (5) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector (6) from the blower unit
control unit on the left-hand side.
aRemove:
-the blower unit control unit bolts (7) ,
-the blower unit control unit.
119711
CLIMATE CONTROL
119714

61A-61
HEATING
Passenger compartment fan assembly control unit: Removal - Refitting
LEFT-HAND DRIVE
61A
aConnect the blower unit control unit connector.
II - FINAL OPERATION.
aRefit:
-the steering wheel lower cover,
-the steering wheel lower cover bolt.
aConnect the connectors to the lower trim on the
dashboard.
aClip on:
-the dashboard lower trim,
-the fuse access flap.
aConnect the hazard warning lights switch connector.
aClip on the "trim - air vent" assembly.
aRefit:
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (MR 411, 83A, Instrument pan-
el),
-the passenger's front airbag (see Passenger's
frontal airbag: Removal - Refitting) (MR 411,
88C, Airbags and pretensioners).
aClip on the upper storage compartment on the driv-
er’s side.
aConnect the battery (see ) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents)(MR 413, 88C, Airbags and seat belt preten-
sioners). AIR CONDITIONING or STANDARD HEATING

61A-66
HEATING
Control panel: Removal - Refitting
61A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector from the control panel (3) .
aUnclip the recirculation control cable (4) .
aRemove the control panel ball joint (5) .
aUnclip the air mixing control cable (6) .
aPress on the tab (7) .
aRemove the control panel ball joint.
aUnclip the air distribution control cable (8) .
aPress on the tab.
aRemove the control panel ball joint (9) .
aDisconnect the connectors from the control panel.aUnclip the control panel (10) .
aRemove the control panel from the dashboard from
above.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aFit the control panel onto the dashboard from above.
aClip on the control panel (11) . AIR CONDITIONING or STANDARD HEATING
119696
CLIMATE CONTROL
119707
119706

61A-71
HEATING
Mixing motor: Removal - Refitting
LEFT-HAND DRIVE, and CLIMATE CONTROL
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the centre console (see Centre console:
Removal - Refitting) (MR 412, 57A, Interior equip-
ment).
aRemove the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aUnclip the glovebox.
aRemove the dashboard lower trim (see Centre front
panel: Removal - Refitting) (MR 412, 57A, Interior
equipment).
aUnclip:
-the fuse access flap (1) ,-the dashboard lower trim.
aDisconnect the connectors from the lower trim on
the dashboard (2) .
aRemove:
-the steering wheel lower cover bolts (3) ,
-the steering wheel lower cover.
aRemove:
-the bolts (4) from the strut,
-the strut. Tightening torquesm
strut bolts21 Nm
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
119506
119711
119713

61A-72
HEATING
Mixing motor: Removal - Refitting
LEFT-HAND DRIVE, and CLIMATE CONTROL
61A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector (5) from the mixer motor.
aRemove:
-the bolts (6) from the air mixing motor,
-the air mixing motor.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the air mixing motor,
-the air mixing motor bolts.
aConnect the air mixing motor connector.
II - FINAL OPERATION.
aRefit:
-the strut,
-the strut bolt.
aTorque tighten the strut bolts (21 Nm).aRefit:
-the steering wheel lower cover,
-the steering wheel lower cover bolt.
aConnect the connectors to the lower trim on the
dashboard.
aClip on:
-the dashboard lower trim,
-the fuse access flap.
aRefit the dashboard lower trim (see Centre front
panel: Removal - Refitting) (MR 412, 57A, Interior
equipment).
aClip the glovebox in position.
aRefit the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aRefit the centre console (see Centre console: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment).
aCheck that the air mixing function is operating cor-
rectly.
121173
Note:
When refitting the mixer motor, make sure that
the drive system notches are correctly posi-
tioned.
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03