sensor RENAULT TWINGO 2009 2.G Chasiss ESP Owner's Guide

38C-51
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF108
PRESENT
OR
STOREDSTEERING WHEEL ANGLE SENSOR
DEF: sensor fault
NOTESNone.
Check the internal fault code of the steering wheel angle sensor using parameter PR113 Steering wheel angle
sensor internal fault code.
Is the internal fault code of the steering wheel angle sensor 10 or 11?
YESCalibrate component 583 using command VP003 Steering wheel angle sensor
(see Configurations and programming).
Clear the ESP sensor offsets using command RZ011 Sensor offsets.
NONote the internal fault code of the steering wheel angle sensor for the purposes of
completing the approval request.
Replace component 583 (see MR 411, Mechanical, 36A, Steering assembly,
Steering column, Removal - Refitting).
ESP_V05_DF108

38C-52
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF126
PRESENT
OR
STOREDCOMBINED SENSOR SIGNAL PLAUSIBILITY
NOTESSpecial notes:
If the fault appears while the vehicle is being driven on a steep gradient, during a very
tight turn or while the vehicle is being transported on a lorry, train, boat etc., with the
engine running, clear the fault and test drive, if possible, to check that the fault does
not return.
Conditions for applying fault finding procedures to stored faults:
The fault is declared present after a road test.
Check that component 1175 is fitted and attached correctly (the arrow indicating the front of the vehicle).
Check the conformity of the tyres (see MR 411, Mechanical, 35A, Wheels and tyres, Tyres: Identification
and Tyre pressure, Identification).
Check the axle assembly geometry (see MR 411, Mechanical, Chassis, Front axle adjustment).
Calibrate component 583 using command VP003 Steering wheel angle sensor (see Configurations
and programming).
Clear the ESP sensor offsets using command RZ011 Sensor offset.
Re-establish dialogue with the ABS/ESP computer, and if no other fault is to be dealt with, clear the computer fault
memory.
Carry out a road test.
If the fault is still present, contact the Techline.
ESP_V05_DF126

38C-59
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF189
PRESENT
OR
STOREDCOMBINED SENSOR CIRCUIT
NOTESUse Wiring Diagram Technical Note, New Twingo.
Check the condition and position of fuse F10 (5 A) in the passenger compartment fuse box (see 81C, Fuse
box).
Check the connection and condition (possible wiring damage) of the connectors of components 1175,1094 and
1016.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
Check the connection and condition (possible wiring damage) of intermediate connector R107.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
Connector of components 1175, 1094, 1016 and intermediate union R107 disconnected.
–check the insulation and continuity of connection AP5 between components 1175 and 1016.
–check the insulation and continuity of connection AP5 between component 1094 and intermediate connector
R107.
–check the insulation and continuity of connection MAM of component 1175 (tightness, oxidation, etc.).
If the connection or connections are faulty (see Technical Note 6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
ESP_V05_DF189

38C-60
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF190
PRESENT
OR
STOREDCOMBINED SENSOR
1.DEF: Sensor internal electronic fault
2.DEF: Sensor incorrectly fitted
3.DEF: Abnormal voltage
NOTESUse the Wiring Diagram Technical Note for New Twingo.
1.DEF
NOTESNone.
Replace component 1175 (see MR 411 Mechanical, 38C, Anti-lock braking system, Lateral acceleration and
yaw speed sensor, Removal - Refitting) then it is essential to clear the ESP sensor offsets using command
RZ011 Sensor offsets.
2.DEF
NOTESNone.
Check the connection and condition (possible wiring damage) of the connector of component 1094.
Check the connection and condition (possible wiring damage) of the connector of component 1175.
Check the connection and condition (possible wiring damage) of intermediate connector R107.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
Check the continuity of connections 4AP and 4AH between components 1094 and 1175.
If the connection or connections are faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
Check that component 1175 is fitted and attached correctly (the arrow indicates the front of the vehicle).
ESP_V05_DF190

38C-61
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF190
CONTINUED
3.DEFNOTESNone.
Check the tightness and condition of the battery terminals (see 80A, Battery).
Check the charging circuit (see 16A, Starting - Charging).
Apply the fault finding procedure for fault DF189 Combined sensor circuit.

38C-65
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF216
PRESENT
OR
STOREDSTEERING WHEEL ANGLE PROGRAMMING OFFSET
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after an extended road test.
With the steering wheel horizontal and the wheels set straight ahead (the wheels must be directly in line with the
vehicle), read the value of the steering wheel angle using parameter PR033 Steering wheel angle.
If the value is not close to 0 ± 5˚, calibrate component 583 using command VP003 Steering wheel angle sensor
(see Configurations and programming).
Clear the ESP sensor offsets using command RZ011 Sensor offsets.
With the steering wheel horizontal and the wheels set straight ahead, turn the steering wheel a quarter of a turn
to the left.
Using parameter PR033 Steering wheel angle, check that the steering wheel angle value is close to - 90.
With the steering wheel horizontal and the wheels set straight ahead, turn the steering wheel a quarter of a turn
to the right.
Using parameter PR033 Steering wheel angle, check that the steering wheel angle value is close to + 90.
If the values are not correct, replace component 583 (see MR 411, Mechanical, 36A, Steering assembly,
Steering column, Removal - Refitting).
Drive in a straight line.
If the steering wheel is not horizontal when the vehicle is driving straight ahead (the vehicle "pulls" to the left or
right).
Check the conformity of the tyres, pressures, wear, and dimensions (see MR 411, Mechanical, 35A, Wheels and
tyres, Tyres: Identification and Tyre pressure, Identification).
Replace the tyre(s) if necessary (see MR 411, Mechanical, 35A, Wheels and tyres, Tyres, Removal -
Refitting).
Adjust the wheel alignment (see MR 411, Mechanical, 30A, General information, Front axle: Adjustment).
With the steering wheel horizontal and the wheels set straight ahead, calibrate component 583 using command
VP003 Steering wheel angle sensor.
Clear the ESP sensor offsets using command RZ011 Sensor offsets.
ESP_V05_DF216

38C-77
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$140.mif
38C
Bosch 8.1 ESP
Vdiag No.: 05
accel.*: accelerationTool
parameter
codeDiagnostic tool title Comments
PR001Front right-hand wheel speed
These parameters indicate the speed in mph (km/h) of
each wheel on the vehicle. PR002Front left-hand wheel speed
PR003Rear right-hand wheel speed
PR004Rear left-hand wheel speed
PR005Computer feed voltageThis parameter indicates the computer supply voltage in
volts.
PR007Longitudinal accelerationThis parameter indicates the longitudinal acceleration of
the vehicle in ms-2. It should be 0 when the vehicle is
stationary.
PR016Lateral accel.* programming offsetThis parameter gives the correction made by the ESP on
the gross value of the lateral acceleration sensor.
PR030Tachometric indexThis parameter specifies the tachometric index entered in
the computer for the tyres fitted to the vehicle.
PR033Steering wheel angleThis parameter gives the steering wheel angle in degrees.
It must be equal to 0˚
± 5˚ with the wheels set straight
ahead.
PR034Yaw angleThis parameter indicates the yaw angle in ˚/s supplied by
the combined sensor. It should be 0 when the vehicle is
stationary.
PR036Transverse accelerationThis parameter indicates the lateral acceleration in g
supplied by the combined sensor.
It should be 0 when the vehicle is stationary.
PR038Vehicle speedThis parameter indicates the vehicle speed in mph (km/h).
PR063Vehicle parametersThis parameter shows whether the configuration (VP004
"Vehicle parameters") matches the vehicle undergoing
fault finding.
PR065Yaw angle programming offsetThis parameter indicates the correction applied by the ESP
to the yaw sensor gross value.
PR066Steering wheel angle
programming offsetThis parameter indicates the correction applied by the ESP
to the gross value of the steering wheel angle sensor.
ANTI-LOCK BRAKING SYSTEM
Fault finding – Parameter summary table

38C-78
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$150.mif
38C
Bosch 8.1 ESP
Vdiag No.: 05
Tool command Diagnostic tool title Comments
RZ001Fault memory This command is used for clearing the computer's stored faults
RZ011Sensor offsetsThis command reinitialises programming of the ESP sensors.
Run this command each time an operation required the steering
wheel angle to be programmed or following any operation on the
axle assemblies.
Also run this command when the combined sensor has been
removed or replaced
SC001Check target teethThis command tests the condition of the teeth on each wheel.
Select the command SC001 and follow the instructions.
The test result should indicate 48 teeth.
SC006Bleed the hydraulic unit and
brake circuitsThis command should only be used if an abnormally long brake
pedal travel is noted during a road test with ABS control (the
system must have been bled beforehand by the usual method).
Select command SC006 and follow the instructions given by the
diagnostic tool.
AC003Front left-hand wheel solenoid
valvesSee the interpretation of command (see Interpretation of
commands).
AC004Front right-hand wheel
solenoid valvesSee the interpretation of command (see Interpretation of
commands).
AC005Rear left-hand wheel solenoid
valvesSee the interpretation of command (see Interpretation of
commands).
AC006Rear right-hand wheel solenoid
valvesSee the interpretation of command (see Interpretation of
commands).
AC013Wheel speed sensor supply
testSee the interpretation of command (see Interpretation of
commands).
AC016Pump motor testSee the interpretation of command (see Interpretation of
commands).
AC187Brake light activation relaySee the interpretation of command (see Interpretation of
commands).
AC195Vehicle speed signalSee the interpretation of command (see Interpretation of
commands).
AC196Hazard warning light activation
requestSee the interpretation of command (see Interpretation of
commands).
ANTI-LOCK BRAKING SYSTEM
Fault finding – Command summary table

38C-80
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$160.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of commands38C
Bosch 8.1 ESP
Vdiag No.: 05
AC013WHEEL SPEED SENSOR SUPPLY TEST
NOTESConditions of use of the command.
Ignition on, engine off.
This command is used to test the supply to every wheel speed sensor.
Select command AC013 and check for 12 V between:
–connections 4T and 4S of component 150,
–connections 4H and 4G of component 151,
–connections 4E and 4C of component 153,
–connections 4N and 4M of component 152.
ESP_V05_AC013

38C-88
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$180.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart38C
Bosch 8.1 ESP
Vdiag No.: 05
ALP2 Locking or braking of one or more wheels
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Check the conformity of the mechanical components (see MR 411, Mechanical,
30A, General information, Brake, Specifications).
REMINDERLocking of wheels on a vehicle fitted with ABS or squealing of the tyres, which feels like
locking to the customer, may be linked to normal operation of the system and should not
always be considered a fault.
Braking with ABS regulation on very poor roads can cause significant squealing.
However, if the wheel(s) is/are actually locking, lift the vehicle in order to be able to rotate the wheels and check:
Possible inversion when connecting the speed sensors.
Use parameters PR001 Front right-hand wheel speed, PR002 Front left-hand wheel speed, PR003 Rear right-
hand wheel speed and PR004 Rear left-hand wheel speed whilst slowly turning the wheels in question and
checking the consistency of the results obtained.
If the value measured is zero, rotate the other wheels to confirm an electrical inversion of the sensors and repair
the wiring harness.
If a single reading is incorrect:
–Check that the sensor casing is secured when rotating.
–Check that the wheel speed sensor mounting is in good condition.
–If that is unsuccessful, replace the corresponding sensor and repeat the check procedure (see MR 411
Mechanical, 38C, Anti-lock braking system, Wheel speed sensor: Removal - Refitting).
–A possible inversion of the pipes on the hydraulic unit (see MR 411, Mechanical, 38C, Anti-lock braking
system, Hydraulic braking unit, List and location of components).
Run commands AC003 Front left-hand wheel solenoid valves, AC004 Front right-hand wheel solenoid
valves, AC005 Rear left-hand wheel solenoid valves and AC006 Rear right-hand wheel solenoid valves while
depressing the brake pedal and check for locking/unlocking cycles on the wheel concerned (see Dealing with
command modes).
If the cycles are not detected on the wheel tested (wheel remains locked), check if they occur on another wheel
(confirmation of a reversal after a repair, see MR 411, Mechanical, 38C, Hydraulic braking unit, List and
location of components).
If the cycles are not detected on a wheel and the pipes have not been inverted, replace component 1094
(see MR 411, Mechanical, 38C, Hydraulic braking unit, Removal- Refitting).
Check that the sensor holder does not rotate (depending on fitting).
Check the quality of the mounting of the wheel speed sensors (correct clipping for the front wheels).
Check the conformity of the targets: the condition and the number of teeth= 48 (using the command SC001
"Check target teeth").
Replace if necessary.
If the fault is still present after these checks, replace component 1094 (see MR 411, Mechanical, 38C, Hydraulic
braking unit, Removal- Refitting).
ESP_V05_ALP2