wiring RENAULT TWINGO 2009 2.G Chasiss ESP Owner's Guide

38C-74
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$130.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of statuses38C
Bosch 8.1 ESP
Vdiag No.: 05
ET017
CONTINUED 2
STATUS "DEPRESSED": Brake pedal released.
–Check the condition, fitting and adjustment of component 160 as well as the conformity of the bulbs.
–Remove (see MR 411, Mechanical, 37A, Mechanical component control, Brake light switch: Removal -
Refitting) and test the operation of component 160:
Continuity between tracks Insulation between tracks
Switch engaged
(Brake pedal released)AP10 and 5A AP10 and 65A
Switch released
(Brake pedal depressed)AP10 and 65A AP10 and 5A
Replace component 160 if necessary.
Connectors of components 645, 172, 173, 639 and 1094, intermediate connectors R107 and R15 and connector
of component 119 (if present on the vehicle) disconnected from connection 65A:
Check the insulation of connection 65A between component 160 and intermediate connector R107.
Check the insulation of connection 65A between component 172 and intermediate connector R107.
Check the insulation of connection 65A between component 173 and intermediate connector R107.
Check the insulation of connection 65A between intermediate connectors R107 and R15.
Check the insulation of connection 65A between component 639 and intermediate connector R15.
Check the insulation of connection 65A between component 645 and intermediate connector R107.
If the connection is faulty (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
If these checks do not reveal any faults:
Perform a complete check of component 645 using the diagnostic tool.
Perform a visual inspection of components 172, 173, 639 present on connections 65A and AP10 (short circuit to
earth).
Replace the component(s) if necessary:
See MR 411 Mechanical, Rear lighting, Rear wing lights, Removal - Refitting for components 172 and 173.
See MR 411 Mechanical, Rear lighting, High level brake light, Removal - Refitting for component 639.

38C-75
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$130.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of statuses38C
Bosch 8.1 ESP
Vdiag No.: 05
ET023ESP ON/OFF BUTTON
NOTESSpecial notes:
Apply the checks only if the PRESSED and RELEASED statuses are not consistent
with the position of the ESP on/off button (RS version only)
Use the Wiring Diagram Technical Note for New Twingo.
PRESSED STATUS
Connector of component 1106 disconnected and without action on the component.
Check that there is no continuity between connections MAM and 4AQ of component 1106.
Otherwise, replace component 1106.
Check the connection and condition (possible wiring damage) of the connectors of components 1106, 1094.
Check the connection and condition (possible wiring damage) of intermediate union R107.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
Connector of components 1106 and 1094 and intermediate union R107 disconnected,
Check the insulation of connection 4AQ between component 1106 and intermediate union R107.
Check the insulation of connection 4AQ between intermediate union R107 and component 1094.
If the connection is faulty (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, or replace it.
If the fault is still present, contact the Techline.
ESP_V05_ET023

38C-76
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$130.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of statuses38C
Bosch 8.1 ESP
Vdiag No.: 05
ET023
CONTINUED
RELEASED STATUS
Connector of component 1106 disconnected and with action on the component.
Check for continuity between connections MAM and 4AQ of component 1106.
Otherwise, replace component 1106.
Check the connection and condition (possible wiring damage) of the connectors of components 1106 and 1094.
Check the connection and condition (possible wiring damage) of intermediate union R107.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
Connector of components 1106 and 1094 and intermediate union R107 disconnected,
check the continuity of connection MAM between component 1106 and the chassis earth (tightness,
oxidation, etc.),
check the continuity of connection 4AQ between component 1106 and intermediate union R107,
check the continuity of connection 4AQ between intermediate union R107 and component 1094.
If the connection or connections are faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.

38C-87
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$180.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart38C
Bosch 8.1 ESP
Vdiag No.: 05
ALP1 No dialogue with the ABS/ESP computer
NOTESOnly address this customer complaint after a complete check with the diagnostic tool.
Use the Wiring Diagram Technical Note for New Twingo.
Try to establish dialogue with an ESP computer on another vehicle to make sure that the diagnostic tool is not
faulty. If the tool is not at fault, and dialogue cannot be established with any other computer on the same vehicle,
the cause could be a faulty computer interfering on the multiplex network.
Check the tightness and condition of the battery terminals (see 80A, Battery).
Check the charging circuit (see 16A, Starting - Charging).
Check that the power supply to the diagnostic socket is correct:
Check for + 12 V on connection BP19 of component 225.
Check for earth on connections MAM and NAM of component 225.
If the connections are faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Apply the fault finding procedure for specification 1. DEF of fault DF001 Computer supply.
Carry out fault finding on the multiplex network using the diagnostic tool (see 88B, Multiplexing).
If dialogue has still not been established after these checks, contact Techline.
ESP_V05_ALP1
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart

38C-88
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$180.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart38C
Bosch 8.1 ESP
Vdiag No.: 05
ALP2 Locking or braking of one or more wheels
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Check the conformity of the mechanical components (see MR 411, Mechanical,
30A, General information, Brake, Specifications).
REMINDERLocking of wheels on a vehicle fitted with ABS or squealing of the tyres, which feels like
locking to the customer, may be linked to normal operation of the system and should not
always be considered a fault.
Braking with ABS regulation on very poor roads can cause significant squealing.
However, if the wheel(s) is/are actually locking, lift the vehicle in order to be able to rotate the wheels and check:
Possible inversion when connecting the speed sensors.
Use parameters PR001 Front right-hand wheel speed, PR002 Front left-hand wheel speed, PR003 Rear right-
hand wheel speed and PR004 Rear left-hand wheel speed whilst slowly turning the wheels in question and
checking the consistency of the results obtained.
If the value measured is zero, rotate the other wheels to confirm an electrical inversion of the sensors and repair
the wiring harness.
If a single reading is incorrect:
–Check that the sensor casing is secured when rotating.
–Check that the wheel speed sensor mounting is in good condition.
–If that is unsuccessful, replace the corresponding sensor and repeat the check procedure (see MR 411
Mechanical, 38C, Anti-lock braking system, Wheel speed sensor: Removal - Refitting).
–A possible inversion of the pipes on the hydraulic unit (see MR 411, Mechanical, 38C, Anti-lock braking
system, Hydraulic braking unit, List and location of components).
Run commands AC003 Front left-hand wheel solenoid valves, AC004 Front right-hand wheel solenoid
valves, AC005 Rear left-hand wheel solenoid valves and AC006 Rear right-hand wheel solenoid valves while
depressing the brake pedal and check for locking/unlocking cycles on the wheel concerned (see Dealing with
command modes).
If the cycles are not detected on the wheel tested (wheel remains locked), check if they occur on another wheel
(confirmation of a reversal after a repair, see MR 411, Mechanical, 38C, Hydraulic braking unit, List and
location of components).
If the cycles are not detected on a wheel and the pipes have not been inverted, replace component 1094
(see MR 411, Mechanical, 38C, Hydraulic braking unit, Removal- Refitting).
Check that the sensor holder does not rotate (depending on fitting).
Check the quality of the mounting of the wheel speed sensors (correct clipping for the front wheels).
Check the conformity of the targets: the condition and the number of teeth= 48 (using the command SC001
"Check target teeth").
Replace if necessary.
If the fault is still present after these checks, replace component 1094 (see MR 411, Mechanical, 38C, Hydraulic
braking unit, Removal- Refitting).
ESP_V05_ALP2

38C-93
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$180.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart38C
Bosch 8.1 ESP
Vdiag No.: 05
ALP7Unexpected ABS operation when using special equipment
(car phone, CB, etc.)
NOTESOnly address this customer complaint after a complete check with the diagnostic tool.
Check that the equipment which is causing the fault is approved.
Check that this equipment was correctly installed without modification of the original wiring, in particular that of
the ABS/ESP.
Connections to earth and to the ABS/ESP supply are forbidden.
ESP_V05_ALP7

38C-100
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$180.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart38C
Bosch 8.1 ESP
Vdiag No.: 05
ALP14 Erratic ESP regulation
NOTESOnly address this customer complaint after a complete check with the diagnostic tool.
Check that the 4 vehicle tyres are identical and in accordance with the manufacturer's recommendations (see
MR 411, Mechanical, 35A, Wheels and tyres, Tyres, Identification).
Check that the pressures of the 4 tyres conform to the manufacturer's recommendations (see MR 411,
Mechanical, 35A, Wheels and tyres, Tyre pressure, Identification).
Using the diagnostic tool, check that the vehicle version corresponds to the vehicle type.
If necessary, reconfigure the vehicle version using command VP004 Vehicle parameters to correspond to the
vehicle type.
Using parameter PR030 Tachometric index, check that the tachometric index corresponds to the vehicle type.
If necessary, reconfigure the tachometric index using command VP007 Tachometric index to correspond to the
vehicle.
Check the connection and condition (possible wiring damage) of the connector of component 1175.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
Check that component 1175 is properly mounted on the body and in the correct direction (the arrow must point
towards the front of the vehicle).
Calibrate component 583 using command VP003 Steering wheel angle sensor (see Configurations and
programming).
Clear the ESP sensor offsets using command RZ011 Sensor offsets.
Clear the faults from the computer using the command RZ001 "Fault memory".
Carry out a road test followed by another check with the diagnostic tool.
If the fault is still present:
–Adjust the axle geometry (see MR 411, Mechanical, 30A, General information, Front axle, Adjustment).
–Calibrate component 583 using command VP003 Steering wheel angle sensor (see Configurations and
programming).
–Clear the ESP sensor offsets using command RZ011 Sensor offsets.
–Clear the faults from the computer using the command RZ001 "Fault memory".
–Carry out a road test followed by another check with the diagnostic tool.
If the fault is still present, contact the Techline.
ESP_V05_ALP14