RENAULT TWINGO 2009 2.G Electrical Equipment - Access Safety Owner's Manual

82D-21
MR-413-X44-82D000$700_eng.mif
V1
82D
ACCESS/SAFETY
Fault finding - Conformity check
SUB-FUNCTION: ACCESS
SR.*: Sunroof
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)1
TailgateET061:Open tailgate
requestPRESENT
ABSENTIn the event of a fault,
apply the
interpretation of
status ET061
(see 87B, UCH).
2ET463:Door(s) or
tailgateOPEN
CLOSEDIn the event of a fault,
apply the
interpretation of
status ET463
(see 87B, UCH).
3
Locking/unlocking
buttonET186:Short press on
door closing
buttonSignal can be
interpreted if the
ignition is
switched off (key
removed from the
ignition switch).
ACTIVE
INACTIVEIn the event of a fault,
refer to the
interpretation of
status ET186
(see 87B, UCH).
4ET189:Long press on
door opening
buttonSignal can be
interpreted if the
ignition is
switched off (key
removed from the
ignition switch).
ACTIVE
INACTIVEIn the event of a fault,
refer to the
interpretation of
status ET189
(see 87B, UCH).
5Electric central
locking buttonET044:Central
Locking buttonPRESSED
RELEASEDIn the event of a fault,
refer to the
interpretation of
status ET044
(see 87B, UCH).
6One-touch window/
SR*ET087:One-touch
window/SR*
authorisationPRESENT
ABSENTIn the event of a fault,
apply the
interpretation of
status ET087
(see 87B, UCH).
MR-413-X44-82D000$700_eng.mif

82D-22
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: ACCESS (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)7Locking
commandAC004:Central door
lockingThis command is
used to test whether
central door locking is
workingIn the event of a
fault, refer to the
procedure for
command AC004
(see 87B, UCH).
8Deadlocking
controlAC035:DeadlockingThis command is
used to test whether
the deadlocking is
working if the vehicle
is configured "WITH"
deadlocking.In the event of a
fault, refer to the
procedure for
command AC035
(see 87B,
Passenger
compartment
connection unit).
9AC005:Central door
unlockingThis command is
used to test whether
the 4 doors, tailgate
and fuel filler flap
unlocking function is
operating correctly.In the event of a
fault, refer to the
procedure for
command AC005
(see 87B,
Passenger
compartment
connection unit).
10Tailgate opening
controlAC061:Tailgate openingThis command is
used to test whether
the tailgate opening
motor is working.In the event of a
fault, refer to the
procedure for
command AC061
(see 87B,
Passenger
compartment
connection unit).

82D-23
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)1
Engine
immobiliserET046:Engine
immobiliserINACTIVE = Vehicle
unprotected, ready
to start.
ACTIVE = Vehicle
protected, starting
impossible.In the event of a
fault, refer to the
interpretation of
status ET046
(see 87B,
Passenger
compartment
connection unit).
2ET008:blank UCHYES = If the UCH
is blank.
NO = if the UCH has
been programmed
with an immobiliser
code.In the event of a
fault, refer to the
interpretation of
status ET008
(see 87B,
Passenger
compartment
connection unit).
3
KeyET185:Key code
receivedYES = If the UCH has
received the
immobiliser code
from the key.
NO = If the UCH does
not receive the
immobiliser code
from the key.In the event of a
fault, refer to the
interpretation of
status ET185
(see 87B,
Passenger
compartment
connection unit).
4ET181:Key allocated to
the vehicleYES = The key is
allocated to the
vehicle.
NO = The key is not
allocated to the
vehicle.In the event of a
fault, refer to the
interpretation of
status ET181
(see 87B,
Passenger
compartment
connection unit).

82D-24
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 1)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection unit)5
KeyET045:Radiofrequency
signal receivedYES = When the
UCH receives a
radiofrequency
signal.
NO = When the
UCH does not
receive a
Radiofrequency
signal.In the event of a fault,
refer to the
interpretation of
status ET045
(see 87B, Passenger
compartment
connection unit).
6ET193:Radiofrequency
signal from a key
allocated to the
vehiclePRESENT =
Reception of a
radiofrequency
signal from a key
allocated to the
vehicle.
ABSENT = No
reception of
frequency signal or
reception of
frequency signal
from a key not
allocated to the
vehicle.In the event of a fault,
refer to the
interpretation of
status ET193
(see 87B, Passenger
compartment
connection unit).
7ET240:Key frequency
(in MHz)433
NONEIf "NONE", check that
there is a
radiofrequency key by
trying with another key
(see 87B, Passenger
compartment
connection unit).
8PR056:Number of keys
allocatedX key(s)In the event of a fault,
refer to the
interpretation of
PR056 (see 87B,
Passenger
compartment
connection unit).

82D-25
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 2)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection unit)9
InjectionET229:Injection
immobiliser
codePROGRAMMED
NOT
PROGRAMMED
UNDETERMINEDIn the event of a fault, refer
to the interpretation of
status ET229 (see 87B,
Passenger compartment
connection unit).
10 ET250:InjectionNOT
PROTECTED
PROTECTEDIn the event of a fault, refer
to the interpretation of
status ET250
(see 17B, Petrol
injection, Conformity
check, Protection)
(see 13B, Diesel
injection, Conformity
check, Protection)
(see 87B, Passenger
compartment
connection unit).
11Starter actuatorET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition
feed.
+ START FEEDIn the event of a fault, refer
to the interpretation of
status ET239 (see 87B,
Passenger compartment
connection unit).

82D-26
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 3)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
Diesel
Injection
(see 13B,
Diesel
Injection)1Computer + after
ignition feedET001:Computer +
after ignition
feedPRESENT
Indicates + after ignition
computer feed.
PRESENT/ABSENTIn the event of a fault,
use the interpretation
of faults DF047
"Computer feed
voltage" and DF015
"Main relay control
circuit ".
2Engine
immobiliserET003:Engine
immobiliser INACTIVE
- INACTIVE: The
injection computer has
recognised the
immobiliser code
transmitted by the UCH.
- ACTIVE: The injection
computer has not
recognised the
immobiliser code
transmitted by the UCH.If ACTIVE, use the
"help" for ET003 on
the tool.
3Code
programmedET006:Code
programmedYES
States whether the
immobiliser code has
been programmed by the
computer or not.
YES: Code programmed
NO: Code not
programmed into the
injection computerIf NO, test the
multiplex network.
4StartingET076:StartingAUTHORISED
Indicates whether or not
starting has been
authorised by the
injection
AUTHORISED: injection
authorises starting.
PROHIBITED: Injection
does not authorise
startingIf PROHIBITED,
carry out a complete
fault finding
procedure on the
preheating system.

82D-27
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 4)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
Petrol
Injection
(see 17B,
Petrol
Injection)1Computer +
after ignition
feedET001:Computer +
after ignition
feedPRESENT
Indicates + after
ignition computer feed.
PRESENT/ABSENTIn the event of a
fault, use the
interpretation of
faults DF047
"Computer feed
voltage" and
DF015 "Main relay
control circuit".
2Engine
immobiliserET003:Engine
immobiliser INACTIVE
- INACTIVE: The
injection computer has
recognised the
immobiliser code
transmitted by the UCH.
- ACTIVE: The injection
computer has not
recognised the
immobiliser code
transmitted by the UCH.If ACTIVE, use "the
help" for ET003 on
the tool.
3Code
programmedET341:Immobiliser
code
programmedYES
States whether the
immobiliser code has
been programmed by
the computer or not.
YES: Code programmed
NO: Code not
programmed into the
injection computerIn the event of a
fault, refer to the
interpretation of
status ET341
"Immobiliser code
programmed".
4StartingET076:StartingAUTHORISED
Indicates whether or not
starting has been
authorised by the
injection
AUTHORISED: injection
authorises starting.
PROHIBITED: Injection
does not authorise
startingIf PROHIBITED,
carry out a complete
fault finding
procedure on the
preheating system.

82D-28
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: STARTING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection
unit)1
EngineET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition
feed.
+ START FEEDIn the event of a fault, refer to the
interpretation of status ET239
(see 87B, Passenger
compartment
connection unit).
And (see 17B, Petrol Injection,
Conformity check, Protection)
(see 13B, Diesel Injection,
Conformity check,
Protection).
2ET142:Engine
operating phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, refer to the
interpretation of status ET142
(see 87B, Passenger
compartment
connection unit).
And (see 17B, Petrol Injection,
Conformity check, Protection)
(see 13B, Diesel Injection,
Conformity check,
Protection).
3PR025:Engine speed0 rpmIn the event of a fault, carry out a
fault finding on the multiplex
network (see 88B).
And (see 17B, Petrol Injection,
Conformity check, Protection)
(see 13B, Diesel Injection,
Conformity check,
Protection).

82D-29
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: STARTING (CONTINUED):1
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
Diesel
Injection
(see 13B,
Diesel
Injection)1EngineET038:Engine– NOT RUNNING
– RUNNINGNONE
2StartingET076:StartingAUTHORISED
Indicates whether or not
starting has been
authorised by the
injection
AUTHORISED: injection
authorises starting.
PROHIBITED: Injection
does not authorise
startingIf PROHIBITED, carry out
a complete fault finding
procedure on the
preheating system.
3AirbagET077:Impact
detectedNO
YES (impact stored by
the injection computer).If ET077 is YES:
Switch off the ignition for
10 seconds, then switch it
back on, so the engine can
be restarted. Then clear
any faults.

82D-30
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: STARTING (CONTINUED 2)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
Petrol
Injection
(see 17B,
Petrol
Injection)1EngineET038:Engine– NOT RUNNING
– RUNNINGNONE
2ET048:Actuator
relay control– ACTIVE
– INACTIVEIn the event of a fault,
consult the interpretation of
status ET048 "Actuator
control relay".
3StartingET076:StartingAUTHORISED
Indicates whether or not
starting has been
authorised by the
injection
AUTHORISED: injection
authorises starting.
PROHIBITED: Injection
does not authorise
startingIf PROHIBITED, carry out a
complete fault finding
procedure on the
preheating system.
4AirbagET077:Impact
detectedNO
YES (impact stored by
the injection computer).If ET077 is YES:
Switch off the ignition for
10 seconds, then switch it
back on, so the engine can
be restarted. Then clear
any faults.