lock RENAULT TWINGO 2009 2.G Electrical Equipment - Airbags And Pretensioners Owner's Manual

88C-33
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF040
CONTINUED
2.DEF
NOTESNone.
Replace the passenger's side sensor component code 1029 (see MR 411, Mechanical, 88C, Airbag and
pretensioners, Side impact sensor: Removal - Refitting).
1.DEF
4.DEF
NOTESNone.
This fault corresponds to an inconsistency between the computer configuration and the vehicle equipment
detected by the computer. The computer has detected the presence of a component additional to its
configuration.
Read configuration LC083 Passenger's front side impact sensor under the heading Configuration reading.
Modify the computer configuration using command CF286 Passenger's front side impact sensor to adjust it to
the vehicle's equipment level.
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat a check using the diagnostic tool and, if there are no faults (do not take the
DF034 "Computer locked'' into account), unlock the computer using the command
VP007 ''Unlock computer''.

88C-34
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF060
PRESENT
MULTIPLEX NETWORK
1.DEF: Multiplex network
2.DEF: Initialisation of instrument panel too long
NOTESNone.
Carry out the fault finding procedure for the multiplex network.
Run a multiplex network test (see 88B, Multiplexing).
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat a check using the diagnostic tool and, if there are no faults (do not take the
DF034 "Computer locked'' into account), unlock the computer using the command
VP007 ''Unlock computer''.
ABGMRSZ_V04_DF060P

88C-35
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF068
PRESENT
PASSENGER FRONT CHEST-LEVEL SIDE AIRBAG CIRCUIT
CO : Open circuit
CC : Short circuit
CC.0 : Short circuit to earth
CC.1 : Short circuit to 12 volts
1.DEF : Configuration
2.DEF : Short circuit between trigger lines
NOTESIf 1.DEF, check and modify the computer configuration using the configuration reading
LC043 Passenger's front chest-level side airbag, then adjust it if it is inconsistent
using the configuration CF224 Passenger's front chest-level side airbag.
Priorities when dealing with a number of faults:
If DF068 is present with fault DF184 Passenger's front buckle pretensioner circuit,
start fault finding by checking the under seat 8-track R334 connector.
Special notes:
Never carry out any measurements on the trigger lines using any tool other than the
XRBAG or CLIP diagnostic tool.
Use dummy module (part no. Elé. 1835 yellow) and the dummy module
(part no. Elé. 1837- 6).
IMPORTANT
Before disconnecting the airbag connector to fit a dummy module, always lock
the trigger lines using the diagnostic tool and command VP006 "Lock
computer".
Use the W iring Diagrams Technical Note, New TWINGO.
Lock the trigger lines using the command VP006 Lock computer.
Switch off the ignition.
Check the condition of the R334 connector under the passenger's front seat (see Wiring Diagram Technical
Note, New Twingo).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Position the dummy module (part no. Elé. 1837- 6) on the 8-track R334 connector under the passenger's
front seat.
Switch on the ignition again.
Read the fault in the AIRBAG / PRETENSIONER field.
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat a check using the diagnostic tool and, if there are no faults (do not take the
DF034 "Computer locked'' into account), unlock the computer using the command
VP007 ''Unlock computer''.
ABGMRSZ_V04_DF068P

88C-36
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF068
CONTINUED 1
If the fault remains "Present":
Check the condition of the airbag computer connector component code 756 (see Wiring Diagram Technical
Note, New Twingo, Component code 756 and MR 411, Mechanical, 88C, Airbag and pretensioners, Airbag
computer: Removal-Refitting).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Faulty wiring between the airbag computer component code 756 and the 8-track R334 connector under the
passenger's front seat.
Check the insulation (+ 12 V, to earth and between the 2 lines) and the continuity of the following
connections:
–Connection code 60BB between component 756 and connector R334,
–Connection code 60BC between component 756 and connector R334.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault has become "Stored":
Switch off the ignition.
Remove the passenger's front side chest-level airbag component code 1104 (see MR 411, Mechanical, 88C,
Airbag and pretensioners, Front side chest-level airbag: Removal - Refitting).
Check the condition of the passenger's front side chest-level airbag connector, component code 1104 (see Wiring
Diagram Technical Note, New Twingo, Component code 1104).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Position the dummy module (part no. Elé. 1835 yellow) on the passenger's front side chest-level airbag
connector component code 1104.
Switch on the ignition again.
Read the fault in the AIRBAG / PRETENSIONER field.
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat a check using the diagnostic tool and, if there are no faults (do not take the
DF034 "Computer locked'' into account), unlock the computer using the command
VP007 ''Unlock computer''.

88C-37
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF068
CONTINUED 2
If the fault remains "Present":
Faulty wiring between the airbag computer component code 1104 and the 8-track R334 connector under the
passenger's front seat.
Check the insulation (+ 12 V, to earth and between the 2 lines) and the continuity of the following
connections:
–Connection code 60H between component 1104 and connector R334,
–Connection code 60K between component 1104 and connector R334.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault has become "Stored":
Replace the passenger's front side chest-level airbag component code 1104 (see MR 411, Mechanical, 88C,
Airbag and pretensioners, Front side chest-level airbag: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat a check using the diagnostic tool and, if there are no faults (do not take the
DF034 "Computer locked'' into account), unlock the computer using the command
VP007 ''Unlock computer''.

88C-38
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF069
PRESENT
PASSENGER'S SIDE CURTAIN AIRBAG CIRCUIT
CO : Open circuit
CC : Short circuit
CC.1 : Short circuit to 12 volts
CC.0 : Short circuit to earth
1.DEF : Configuration
2.DEF : Short circuit between trigger lines
NOTESIf 1.DEF, check and modify the computer configuration using the configuration reading
LC041 Passenger's side curtain airbag then modify it if it is inconsistent using the
configuration CF222 Passenger's side curtain airbag.
Special notes:
Never carry out any measurements on the trigger lines using any tool other than the
XRBAG or CLIP diagnostic tool.
Use the dummy module (part no. Elé. 1835 yellow) and the dummy module (part
no. Elé. 1837- 2) with command VP006 Lock computer.
IMPORTANT
Before disconnecting the airbag connector to fit a dummy module, always lock
the trigger lines using the diagnostic tool and command VP006 "Lock
computer".
Use the W iring Diagrams Technical Note, New TWINGO.
Lock the trigger lines using command VP006 "Lock computer".
Switch off the ignition.
Check the condition of the passenger's side curtain airbag intermediate connector R15 component code 1102
(see Wiring Diagram Technical Note, New Twingo and Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Position the dummy module (part no. Elé. 1837- 2) on intermediate connector R15 of the passenger's side
curtain airbag.
Switch on the ignition again.
Read the fault in the AIRBAG / PRETENSIONER field.
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat the check using the diagnostic tool and, if there are no faults (ignore DF034
Computer locked), unlock the computer using command VP007 Unlock computer.
ABGMRSZ_V04_DF069P

88C-39
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF069
CONTINUED 1
If the fault remains "Present":
Check the condition of the airbag computer connector component code 756 (see Wiring Diagram Technical
Note, New Twingo, Component code 756 and MR 411, Mechanical, 88C, Airbag and pretensioners, Airbag
computer: Removal-Refitting).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Faulty wiring between the airbag computer component code 756 and the intermediate connector R15 of the
passenger's side curtain airbag component code 1102.
Check the insulation (+ 12 V, to earth and between the 2 lines) and the continuity of the following
connections:
–Connection code 60CA between component 756 and connector R15,
–Connection code 60CB between component 756 and connector R15.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault has become "Stored":
Switch off the ignition.
Remove the passenger's side curtain airbag component code 1102 (see MR 411, Mechanical, 88C, Airbag and
pretensioners, Curtain side airbag: Removal - Refitting).
Check the condition of the passenger's side curtain airbag connector component code 1102 (see Wiring
Diagram Technical Note, New Twingo, Component code 1102 and Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Position the dummy module (part no. Elé. 1835 yellow) on the connector of the passenger's side curtain airbag
component code 1102.
Switch on the ignition again.
Read the fault in the AIRBAG / PRETENSIONER field.
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat the check using the diagnostic tool and, if there are no faults (ignore DF034
Computer locked), unlock the computer using command VP007 Unlock computer.

88C-40
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF069
CONTINUED 2
If the fault remains "Present":
Faulty wiring between the passenger's side curtain airbag component code 1102 and the intermediate
connector R15.
Check the insulation (+ 12 V, to earth and between the 2 lines) and the continuity of the following
connections:
–Connection code 60CA between component 1102 and connector R15,
–Connection code 60CB between component 1102 and connector R15.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault has become "Stored":
Replace the passenger's side curtain airbag component code 1102 (see MR 411, Mechanical, 88C, Airbag and
pretensioners, Curtain side airbag: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat the check using the diagnostic tool and, if there are no faults (ignore DF034
Computer locked), unlock the computer using command VP007 Unlock computer.

88C-41
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF070
PRESENT
DRIVER SIDE CURTAIN AIRBAG CIRCUIT
CO : Open circuit
CC : Short circuit
CC.1 : Short circuit to 12 volts
CC.0 : Short circuit to earth
1.DEF : Configuration
2.DEF: Short circuit between trigger lines
NOTESIf 1.DEF, check and modify the computer configuration using the configuration reading
LC040 Driver's side curtain airbag, then modify it if it is inconsistent using
configuration CF221 Driver's side curtain airbag.
Special notes:
Never carry out any measurements on the trigger lines using any tool other than the
XRBAG or CLIP diagnostic tool.
Use dummy module (part no. Elé. 1835 yellow) and the dummy module
(part no. Elé. 1837- 2).
IMPORTANT
Before disconnecting the airbag connector to fit a dummy module, always lock
the trigger lines using the diagnostic tool and command VP006 "Lock
computer".
Use the W iring Diagrams Technical Note, New TWINGO.
Lock the trigger lines using command VP006 Lock computer.
Switch off the ignition.
Check the condition of the intermediate connector R15 of the driver's side curtain airbag component code 1101
(see Wiring Diagram Technical Note, New Twingo and MR 411, Mechanical, 88C, Airbag and pretensioners,
Curtain side airbag: Removal - Refitting).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Position the dummy module (part no. Elé. 1837- 2) on the intermediate connector R15 of the driver's side
curtain airbag component code 1101.
Switch on the ignition again.
Read the fault in the AIRBAG / PRETENSIONER field.
AFTER REPAIRReconnect the computer and the ignition module of the driver's side curtain airbag
module then switch the ignition back on. Clear the computer fault memory using
command RZ001 Fault memory. Switch the ignition off and then on again.
Repeat the check using the diagnostic tool and, if there are no faults (ignore DF034
Computer locked), unlock the computer using command VP007 Unlock computer.
ABGMRSZ_V04_DF070P

88C-42
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF070
CONTINUED
If the fault remains "Present":
Check the condition of the airbag computer connector, component code 756 (see Wiring Diagram Technical
Note, New Twingo, Component code 756 and MR 411, Mechanical, 88C, Airbag and pretensioners, Airbag
computer: Removal - Refitting).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Faulty wiring between the airbag computer component code 756 and the intermediate connector R15 of the
driver's side curtain airbag component code 1101.
Check the insulation (+ 12 V, to earth and between the 2 lines) and the continuity of the following
connections:
–Connection code 60BY between component 756 and connector R15,
–Connection code 60BZ between component 756 and connector R15.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
AFTER REPAIRReconnect the computer and the ignition module of the driver's side curtain airbag
module then switch the ignition back on. Clear the computer fault memory using
command RZ001 Fault memory. Switch the ignition off and then on again.
Repeat the check using the diagnostic tool and, if there are no faults (ignore DF034
Computer locked), unlock the computer using command VP007 Unlock computer.