battery RENAULT TWINGO 2009 2.G Electrical Equipment - Electric Windows, Sunroof User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO, Model: RENAULT TWINGO 2009 2.GPages: 54, PDF Size: 0.25 MB
Page 27 of 54
87D-27
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 6Driver's and passenger's windows do not operate at all with the
driver's switch only
Applies to:Driver's one-touch electric windows and passenger's
electric window
Left-hand drive vehicle
NOTESUse Technical Note Wiring Diagram, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Use a multimeter.
Remove the driver's window winder switch (see
MR 411 mechanical, 87D Electric windows -
Sunroof, driver's door front
window winder switch: Removal - Refitting).
Use an ohmmeter to check the continuity on
connection MAM between component 1512 and
the chassis earth.
Is the continuity good?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D Electric windows -
Sunroof, Driver's door front
window winder switch: Removal - Refitting).
NOCheck that earth MAM is correctly mounted
on the chassis. If the earth is faulty, clean and
retighten it. If there is a repair procedure (see
Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
Page 28 of 54
87D-28
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 6Driver's and passenger's windows do not operate at all with the
driver's switch only
Applies to:Driver's one-touch electric windows and passenger's
electric window
Right-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Use a multimeter.
Remove the driver's window winder switch (see
MR 411 mechanical, 87D Electric windows -
Sunroof, driver's door
front window winder switch: Removal -
Refitting).
Use an ohmmeter to check the continuity on
connection MAN between component 1512 and
the chassis earth.
Is the continuity good?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D, Electric windows -
Sunroof, Driver's door front window winder
switch: Removal - Refitting).
NOCheck that earth MAN is correctly mounted
on the chassis. If the earth is faulty, clean and
retighten it. If there is a repair procedure (see
Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
Page 29 of 54
87D-29
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
Continuity fault on connection SPB3. Pay
attention to the intermediate connector. If
there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
ALP 7 The passenger window does not operate at all with any switch
Applies to:Driver's one-touch electric windows and passenger's
electric window
Left-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Check that the fuses are sound.
Use a 21 W test light.
Remove the passenger's window winder switch
(see MR 411 mechanical, 87D Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal -Refitting) and disconnect its
connector.
Use the test light connected to the chassis earth
to check the feed on connections 22D and 22C
on component 133.
Are the feeds correct?
YES
Shunt connection 22B to MAN and 22A to 22C
to lower the window (to raise it, shunt 22A to
MAN and 22B to 22D), on the connector of
component 133.
Does the window move?
YES
Remove the passenger's window winder switch
(see MR 411 mechanical, 87D Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal -Refitting).
NORemove the driver's window winder switch
(see MR 411 mechanical, 87D, Electric
windows - Sunroof, driver's door front
window winder switch: Removal -
Refitting) and disconnect its connector.
Use a test light connected to the chassis
earth to check the feed on connection SPB3
of component 1512.
Is the feed correct?
NO
NOYES
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
BA
Page 31 of 54
87D-31
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 7 The passenger window does not operate at all with any switch
Applies to:Driver's one-touch electric windows and passenger's
electric window
Right-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Check that the fuses are sound.
Use a 21 W test light.
Remove the passenger's window winder switch
(see MR 411 mechanical, 87D Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal -Refitting) and disconnect its
connector.
Use the test light connected to the chassis earth
to check the feed on connections 22D and 22C
on component 133.
Are the feeds correct?
YES
Shunt connection 22B to MAM and 22A to 22C
to lower the window (to raise the window
shunt 22A to MAM and 22B to 22D), on
connector of component 133.
Does the window move?
YES
Replace the passenger's window winder switch
(see MR 411 mechanical, 87D Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal -Refitting).
NORemove the driver's window winder switch
(see MR 411 mechanical, 87D, Electric
windows - Sunroof, driver's door front
window winder switch: Removal -
Refitting) and disconnect its connector.
Use a test light connected to the chassis
earth to check the feed on connection SPB3
of component 1512.
Is the feed correct?
NO
NOContinuity fault on connection SPB3. Pay
attention to the intermediate connector. If
there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
YES
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
BA
Page 33 of 54
87D-33
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 8The passenger window does not operate at all with the passenger
switch only
Applies to:Driver's one-touch electric windows and passenger's
electric window
Left-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Use a 21 W test light.
Remove the passenger's window winder switch
(see MR 411 mechanical, 87D, Electric
windows - Sunroof,
passenger's door front window winder
switch:
Removal -Refitting) and disconnect its
connector.
Connect a test light to connections MAN and
22C (or 22D) of component 133.
Does the bulb light up correctly?
YES
Replace the passenger's window winder switch
(see MR 411 mechanical, 87D, Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal - Refitting).
NOContinuity fault on connection MAN.
Check that earth MAN is correctly mounted
on the chassis. If the earth is faulty, clean and
retighten it.
Otherwise the fault is caused by the wiring;
if there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring; if not, replace it.
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
Page 34 of 54
87D-34
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 8The passenger window does not operate at all with the passenger
switch only
Applies to:Driver's one-touch electric windows and passenger's
electric window
Right-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Use a 21 W test light.
Remove the passenger's window winder switch
(see MR 411 mechanical, 87D Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal -Refitting) and disconnect its
connector.
Connect a test light to connection MAM and 22C
(or 22D) of component 133.
Does the bulb light up correctly?
YES
Replace the passenger's window winder switch
(see MR 411 mechanical, 87D, Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal - Refitting).
NOContinuity fault on connection MAM.
Check that earth MAM is correctly mounted
on the chassis. If the earth is faulty, clean and
retighten it.
Otherwise the fault is caused by the wiring; if
there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring; if not, replace it.
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
Page 35 of 54
87D-35
MR-413-X44-87D000$472_eng.mif
V1
87D
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart
ALP 9 Driver's window rises jerkily in 50 mm stages
Applies to:Driver's one-touch electric windows and passenger's
electric window
Left-hand drive and right-hand drive vehicles
NOTESThe battery must be charged and + after ignition feed switched on.
The fault is due to a loss of initialisation.
To cure the fault (see Electric sunroof: Initialisation).
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
Page 43 of 54
87D-43
MR-413-X44-87D000$944_eng.mif
V1
87D
ELECTRIC WINDOWS - SUNROOF
Electric sunroof - Fault finding chart
ALP 1 The sunroof does not operate at all
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Check that the fuses are sound.
Use a multimeter and a 21 W test bulb.
Use the diagnostic tool.
Read the configuration in the UCH and check
that configuration LC070 “One touch
window\sunroof” * is correctly configured
“with”.
Does parameter LC070 display WITH?
YES
Move the sunroof control to the “Closed”
position and press and hold the central part of
the control.
After pressing the central part of the control
for approximately 10 seconds, does the roof
move smoothly?
YES
See ALP 4.
NOModify the configuration (see 87B,
Passenger compartment connection unit).
NOCheck the feed by connecting a test light between
connections BP93 and MAM of component 1579.
Does the bulb light up correctly?
YES NO
Check the feed by connecting a test light
between connection BP93 and the chassis earth.
Does the test light work
correctly?
NO YES
Fault on connection MAM between
component 1579 and the chassis earth; be
careful of the intermediate connector R339.
If there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it. When the wiring has
been repaired, carry out the initialisation (see
Electric sunroof: Initialisation).
Fault on connection BP93 between
components 1579 and 1016; be careful of the
intermediate connectors R339 and R301.
If there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it. After the wiring has
been repaired, carry out an initialisation (see
Electric sunroof: Initialisation).
A
New Twingo
MR-413-X44-87D000$944_eng.mif
Page 48 of 54
87D-48
MR-413-X44-87D000$944_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric sunroof - Fault finding chart87D
ALP 2 The sunroof does not operate in certain positions on the control
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Carry out the various checks with a multimeter.
Does the sunroof operate in at least one of
the control positions?
YES
Disconnect the sunroof switch connector
(component 317). Use an ohmmeter and the
table below to check the conformity and correct
operation of the sunroof control.
Connect the ohmmeter between connections 52D
and
Control position52G52H52J
Tilt position infinite100 Ω
Maximum100 Ω
Maximum
Closed infinite infinite100 Ω
Maximum
Sliding position 1100 Ω
Maximuminfinite100 Ω
Maximum
Sliding position 2100 Ω
Maximuminfinite infinite
Sliding position 3100 Ω
Maximum100 Ω
Maximuminfinite
Pressed100 Ω
Maximum100 Ω
Maximum100 Ω
Maximum
NOSee ALP 1.
A
Page 50 of 54
87D-50
MR-413-X44-87D000$944_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric sunroof - Fault finding chart87D
ALP 3The sunroof does not close when driving
(anti-pinch is triggered)
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Does the sunroof operate when the vehicle is
stationary?
YES
Initialise the sunroof (see Electric sunroof:
Initialisation).
Is the fault still present?
YES
Measure the vehicle speed signal by connecting
a multimeter (in frequency mode) or an
oscilloscope between connection 47F of
connector R301 and the chassis earth (See
ALP 3 Procedure).
Is the vehicle speed signal correct?
YES
Disconnect the sunroof computer connector (see
MR 411 mechanical, 87D,
Electric windows-sunroof, Electric sunroof
computer: Removal - Refitting) and measure
the vehicle speed signal by connecting a
multimeter (in frequency mode) or an
oscilloscope between connection 47F and
connection MAM of component 1579 (See ALP3
Procedure).
Is the vehicle speed signal correct?
YES
NO See ALP 1.
NOFault solved
NO
Continuity fault on connection 47F between
component 1579 and connector R301. Pay
close attention to the intermediate
connector R339.
Disconnect the other components attached to
this connection before working on the wiring
(e.g. radio, electric power-assisted steering).
If there is a repair procedure (see
Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair),
repair the wiring, otherwise replace it.
NO
Replace the sunroof computer (see MR 411
mechanical, 87D, Electric windows -
sunroof, Electric sunroof computer:
Removal - Refitting).
A