warning RENAULT TWINGO 2009 2.G Electrical Equipment - Instrument Panel User Guide

83A-19
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function

Vdiag No.: 04, 08
83A
–Illumination of the “Service” warning light:
Illumination of the “Service” warning light alone characterises a warning light test phase by the instrument panel.
Illumination of this warning light can be accompanied by other warnings:
“Service” warning light + “ - - ” on the speed display:
–Vehicle speed circuit fault warning.
“Service” warning light + 3 dashes in place of the set speed + Disappearance of the symbol:
–Cruise control fault warning.
“Service” warning light + 3 dashes in place of the cruising speed + Disappearance of the symbol:
–Speed limiter fault warning.
“Service” warning light + “Distance/time before service” symbol flashing + “- - - - -” in place of the Distance/time
before service value:
–“Distance/time before service” warning exceeded in time (NOT used on the New Twingo).
“Service” warning light + “Distance/time before service” symbol flashing + “0” displayed on the multifunction display:
–“Distance/time before service” warning exceeded in distance.
“Service” warning light + “ESP” warning light (located on the rev counter):
–ESP fault warning.
–ESP in regulation with fault warning.
“Service” warning light alone:
–ESP present but rev counter not detected. The instrument panel no longer detects the multiplexed rev
counter signal even though it is configured with ESP; the rev counter may be faulty.

83A-20
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function

Vdiag No.: 04, 08
83A
“Service” warning light + “ABS” warning light:
–ABS fault warning.
“Service” warning light + “Particle filter” warning light:
–“Major particle filter fault” warning.
The New Twingo does not currently have a particle filter.
“Service” warning light + “OBD” warning light:
–“Combustion misfire” warning.
“Service” warning light + “OBD” warning light flashing:
–“Destructive combustion misfire” warning.
“Service” warning light + “Airbag fault warning” warning light:
–“Airbag fault” warning.
“Service” warning light + “Sinusoid” warning light:
–“Minor injection fault” warning.
–“Water in diesel fuel” warning (on diesel configuration only).
–“Sequential gearbox fault” warning (on sequential gearbox configuration only).

83A-29
MR-413-X44-83A000$504.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Conformity check
MAIN SCREEN
SUB-FUNCTION: DISPLAY
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Instrument
panel lighting.ET004Side lights controlSide lights
onACTIVE
In the event of a fault, consult the
interpretation of status ET004
Side lights switch Side lights
offINACTIVE
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Instrument
panel lightingET004:Side lights controlSide lights
onACTIVE
In the event of a fault, consult the
interpretation of status ET004
Side lights switch. Side lights
offINACTIVE
Direction
indicator signalET245:Direction indicatorsActivated ACTIVE
In the event of a fault, refer to the
interpretation of status ET245
Indicators. In rest
positionINACTIVE
Fault signalET248:Stop warning light
activated by the
system1- Injection
2-Coolant
temperature
3-Oil pressure
4-Brake fluid level
5- Electronic Braking
Distribution
6-Electric power-
assisted steering
7-Battery chargeSee the interpretation of ET248
STOP warning light activated
by the system.
TDB_V04_CCONF / TDB_V08_CCONF

Vdiag No.: 04, 08
MR-413-X44-83A000$504.mif

83A-30
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION: DISPLAY (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Fault signalET249:Service warning
light activated by
the system1-Multiplex line
communication
2- Injection
3-Water present in diesel
fuel
4-Sequential gearbox
5-Vehicle speed circuit
6-Cruise control/speed
limiter
7-ESP
8-ABS
9-Oil change interval
10- Particle filter
11- Airbag
12- OBDSee the interpretation of
ET249 SERVICE warning
light activated by the
system
Parking brake
signalET097:Parking brakeAutomatic
parking brake
onAPPLIED
In the event of a fault, consult
the interpretation of status
ET097 Parking brake Parking
brake
releasedRELEASED
Minimum brake
fluid level signalET019:Minimum brake
fluid levelMinimum
brake fluid
reservoir
levelYES
In the event of a fault, consult
the interpretation of status
ET019 Minimum brake fluid
level. Normal brake
fluid
reservoir
levelNO
Oil pressure
present signalET096:Oil pressure
contactEngine
runningOPENIn the event of a fault,
consult the interpretation of
fault DF009 “oil pressure
sensor” Engine
stoppedCLOSED

83A-31
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION: DISPLAY (CONTINUED)
SUB-FUNCTION: TRIP COMPUTER
*ADAC: Trip Computer
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Instrument panel
warning light
operation checkAC009:Instrument
panel warning
lightsIllumination of all of the
warning lights
simultaneously on the
displayImportant: This command
causes the Airbag system
stored fault to occur again
(see 88C Airbag and
pretensioners).
–Before running the
command:
Deal with all of the Airbag
faults.
(see 88C, Airbag and
pretensioners).
–After running the
command:
Clear the Airbag system
stored faults.
If one or more warning lights
do not come on, contact
Techline.
Backlighting
operation checkAC010:LightingGradual illumination of
the instrument panel
backlightingWITHOUT
Instrument panel
buzzer checkAC006:BuzzerInstrument panel buzzer
operation–If the buzzer is faulty,
contact Techline.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
ADAC* button
status signalET030:ADAC* scroll
button
Button
depressedDEPRESSED
In the event of a fault, consult the
interpretation of status ET030
ADAC* scroll button.
Button
releasedRELEASED
Clock setting
button status
signalET095:Clock setting
button
Button
depressedDEPRESSED
Contact the Techline.Button
releasedRELEASED

83A-34
MR-413-X44-83A000$560.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Status summary table
*ADAC: Trip Computer Tool status Diagnostic tool title Specification
ET004Side lights control Inactive/Active
ET019Minimum brake fluid level Yes/No
ET030ADAC* scroll button Released/Pressed
ET095Clock setting button Released/Pressed
ET097Parking brake Engaged/Released
ET245Direction indicators Inactive/Active
ET248Stop warning light activated by the
system1 : Injection
2 : Coolant temperature
3 : Oil pressure
4 : Brake fluid level
5 : Electronic Braking Distribution
6 : Electric power assisted steering
7 : Battery charge
ET249Service warning light activated by the
system1 : Multiplex line communication
2 : Injection
3 : Water present in diesel fuel
4 : Sequential gearbox
5 : Vehicle speed circuit
6 : Cruise control/speed limiter
7 : ESP
8 : ABS
9 : Oil service interval
10 : Particle filter
11 : Airbag
12 : OBD

Vdiag No.: 04, 08
MR-413-X44-83A000$560.mif

83A-41
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET248
STOP WARNING LIGHT ACTIVATED BY THE SYSTEM
If the STOP WARNING LIGHT is illuminated, check for faults and check the conformity of the systems
concerned.
1 : Injection
2 : Coolant temperature
3 : Oil pressure
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
4 : Brake fluid level
See the interpretation of ET019 MINIMUM BRAKE FLUID LEVEL.
5 : Electronic Braking Distribution
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
6 : Electric power assisted steering
Carry out fault finding on the EPAS system (see 36B, Power-assisted steering).
7 : Battery charge
Carry out fault finding on the charging circuit (see Technical Note 6014A, Checking the charging circuit).
If there are no faults, carry out a multiplex network check (see 88B, Multiplex).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET248 / TDB_V08_ET248

83A-42
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET249
SERVICE WARNING LIGHT ACTIVATED BY THE SYSTEM
If the SERVICE WARNING LIGHT is illuminated, check for faults and check the conformity of the systems
concerned.
1 : Multiplex line communication
Check the multiplex network (see 88B, Multiplex)
2 : Injection
3 : Water present in diesel fuel
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
4 : Sequential gearbox
Carry out fault finding on the sequential gearbox (see 23A, Sequential gearbox).
5 : Vehicle speed circuit
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
6 : Cruise control/speed limiter
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
7 : ESP
8 : ABS
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
9 : Oil service interval
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
10 : Particle filter
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
11 : Airbag
Carry out fault finding on the Airbag system (see 88C, Airbag and pretensioners).
12 : OBD
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
If there are no faults, carry out a multiplex network check (see 88B, Multiplex).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET249 / TDB_V08_ET249

83A-48
MR-413-X44-83A000$896.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Customer complaints
NOTESOnly refer to the customer complaints after a complete check using the diagnostic
tool
Carry out fault finding on the multiplex network.
Carry out fault finding on the instrument panel.
NO COMMUNICATION WITH THE INSTRUMENT PANEL
THE INSTRUMENT PANEL DOES NOT LIGHT UPALP 1
THE FUEL LEVEL INDICATOR DOES NOT DISPLAY FULL
ALP 2
ADDITION OF FUEL NOT REGISTERED (NOT FULL)
ALP 3
DISPLAY JAMMED WHEN DRIVING (NOT MECHANICAL)
ALP 4
FAULT WITH NO WARNING GIVEN BY WARNING LIGHT (NO ADDITION OF FUEL
SINCE THE FAULT)ALP 5
FAULT WITH NO WARNING GIVEN BY WARNING LIGHT (ADDITION OF FUEL SINCE
THE FAULT)ALP 6
FAULT WITH DELAYED WARNING
ALP 7

Vdiag No.: 04, 08
MR-413-X44-83A000$896.mif

83A-59
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 5Fault with no warning given by warning light (no addition of fuel
since the fault)
NOTESPut the vehicle in + after ignition.
See Wiring diagram Technical Note, New Twingo.
Check the instrument panel warning lights, component
code 247.Replace the instrument panel,
component code 247 (see
MR 411, Mechanical, 83A,
Instrument panel, Instrument
panel: Removal - Refitting). Does the fuel warning light illuminate for 3 seconds when
+ after ignition is switched on?
Record the resistance value provided by the CLIP tool.
Compare the value from the CLIP tool with the warning
resistance, which should be 260 ΩΩ Ω Ω
.
Is this value above or equal to 260 ΩΩ Ω Ω
?Contact the Techline.
Rock the vehicle and check whether the resistance changes by
± 5 ΩΩ Ω Ω
.
Is there a change in the resistance value?Contact the Techline.
NO
YES
YES
NO
YES
NO
A
TDB_V04_ALP5/TDB_V08_ALP5