RENAULT TWINGO 2009 2.G Electrical Equipment - Instrument Panel Owner's Guide

83A-31
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION: DISPLAY (CONTINUED)
SUB-FUNCTION: TRIP COMPUTER
*ADAC: Trip Computer
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Instrument panel
warning light
operation checkAC009:Instrument
panel warning
lightsIllumination of all of the
warning lights
simultaneously on the
displayImportant: This command
causes the Airbag system
stored fault to occur again
(see 88C Airbag and
pretensioners).
–Before running the
command:
Deal with all of the Airbag
faults.
(see 88C, Airbag and
pretensioners).
–After running the
command:
Clear the Airbag system
stored faults.
If one or more warning lights
do not come on, contact
Techline.
Backlighting
operation checkAC010:LightingGradual illumination of
the instrument panel
backlightingWITHOUT
Instrument panel
buzzer checkAC006:BuzzerInstrument panel buzzer
operation–If the buzzer is faulty,
contact Techline.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
ADAC* button
status signalET030:ADAC* scroll
button
Button
depressedDEPRESSED
In the event of a fault, consult the
interpretation of status ET030
ADAC* scroll button.
Button
releasedRELEASED
Clock setting
button status
signalET095:Clock setting
button
Button
depressedDEPRESSED
Contact the Techline.Button
releasedRELEASED

83A-32
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION : GAUGING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Fuel sender
operation checkPR040:Current fuel levelThe current fuel level
depends on the vehicle
body movements.In the event of a fault, consult the
interpretation of fault DF007
Fuel sender circuit.
Filtered fuel
level checkPR041:Filtered fuel levelThe filtered fuel level is
independent of the
variations created by the
vehicle body movements.In the event of a fault, consult the
interpretation of parameter
PR041 Filtered fuel level.
Fuel sender
resistance
checkPR002:Fuel sender unit
resistanceThe fuel sender resistance
depends on the fuel level.
In reserve: 260 ΩΩ Ω Ω
Full: 38 ΩΩ Ω ΩIf R < 5 ΩΩ Ω Ω
or R> 350 ΩΩ Ω Ω
: Faulty
fuel sender.
In the event of a fault, consult the
interpretation of fault DF007
Fuel sender circuit.

83A-33
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB FUNCTION: ODOMETRY IN KM
SUB FUNCTION: ODOMETRY IN MILES
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Check the
general distance
travelled by the
vehicle in kmPR025:Odometry in kmDisplays the vehicle
distance in km.WITHOUT
Check the
distance before
oil service in kmPR005:Distance to next oil
service: current
value in kmDisplays the distance
remaining in kms before
the recommended oil
service.WITHOUT
Check the
interval between
each oil service
in kmPR007:Oil change
frequency in km.Initial oil service interval
in km.WITHOUT
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Check the
general distance
travelled by the
vehicle in milesPR026:Odometer in milesDisplays the vehicle
distance in miles.WITHOUT
Check the
distance before
oil service
in milesPR023:Oil service
interval: current
value in milesDisplays the distance
remaining in miles before
the recommended oil
service.WITHOUT
Check the
interval between
each oil service
in milesPR024:Oil change
frequency in miles.Initial oil service interval in miles.

83A-34
MR-413-X44-83A000$560.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Status summary table
*ADAC: Trip Computer Tool status Diagnostic tool title Specification
ET004Side lights control Inactive/Active
ET019Minimum brake fluid level Yes/No
ET030ADAC* scroll button Released/Pressed
ET095Clock setting button Released/Pressed
ET097Parking brake Engaged/Released
ET245Direction indicators Inactive/Active
ET248Stop warning light activated by the
system1 : Injection
2 : Coolant temperature
3 : Oil pressure
4 : Brake fluid level
5 : Electronic Braking Distribution
6 : Electric power assisted steering
7 : Battery charge
ET249Service warning light activated by the
system1 : Multiplex line communication
2 : Injection
3 : Water present in diesel fuel
4 : Sequential gearbox
5 : Vehicle speed circuit
6 : Cruise control/speed limiter
7 : ESP
8 : ABS
9 : Oil service interval
10 : Particle filter
11 : Airbag
12 : OBD

Vdiag No.: 04, 08
MR-413-X44-83A000$560.mif

83A-35
MR-413-X44-83A000$616.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Interpretation of statuses
ET004
SIDE LIGHTS SWITCH
NOTESSpecial notes:
–Only perform these tests if the statuses do not correspond with the system
programming functions.
–Side lights on.
INACTIVE
NOTESIf the status becomes “INACTIVE”, apply the following fault
finding procedure.
Check fuse F43 (10A) of the passenger compartment fuse box, component code 1016.
Check the connection and condition of the connector of component 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the + 12 V supply to connection LPG of component 247.
If the connection is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance of:
Connection LPG between component 1016 and component 247.
Connection MAN35 of component 247.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET004 / TDB_V08_ET004

Vdiag No.: 04, 08
MR-413-X44-83A000$616.mif

83A-36
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET019
MINIMUM BRAKE FLUID LEVEL
NOTESThere must be no present or stored faults.
Check the brake fluid level in the reservoir.
If the brake fluid is at the maximum level and ET019 MINIMUM BRAKE FLUID LEVEL is “YES”:
Disconnect the connector on component 207.
If status ET019 MINIMUM BRAKE FLUID LEVEL becomes NO, replace component 207.
Check the earth insulation of:
connection 30A between component 247 and component 207.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the brake fluid is at the minimum level and ET019 MINIMUM BRAKE FLUID LEVEL is “NO”:
Disconnect the connector on the Brake fluid minimum level sensor, component code 207.
Check for continuity between connection 30A and connection MAS of the Brake fluid minimum level sensor,
component code 207.
If there is no continuity, replace the Brake fluid minimum level sensor, component code 207.
Check for continuity:
On connection 30A between component 207 and component 247.
On connection MAS between component 207 and the vehicle earth.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET019 / TDB_V08_ET019

83A-37
MR-413-X44-83A000$616.mif
V5

Vdiag No.: 04, 08INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
ET030
ADAC* SCROLL BUTTON
NOTESVehicle under + after ignition feed.
“RELEASED”
STATUS
button
pressed
*ADAC: Trip ComputerCheck the condition and connection of the instrument panel connector,
component code 247.
Press and hold the Trip Computer button and check the continuity between
connection MAM and connection 47K of component 145.
If there is no continuity, replace component 145 (see MR 411, Mechanical, 84A,
Controls - Signals, Wiper switch: Removal - Refitting).
Check the continuity and insulation to + 12 V on:
Connection 47K between component 145 and component 247.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
Check the earth and insulation to + 12 V of:
–Connection MAN between component 145 and the chassis earth.
–Connection MAN between component 145 and the chassis earth.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET030 / TDB_V08_ET030

83A-38
MR-413-X44-83A000$616.mif
V5

Vdiag No.: 04, 08INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
ET097
PARKING BRAKE
NOTESSpecial notes:
Only apply the checks if the APPLIED and RELEASED statuses are not consistent
with the lever position:
–APPLIED when the lever is released,
–RELEASED when the lever is applied.
APPLIED
STATUS
when lever is
released
Check the connection and condition of the connector of component 156.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the connector, otherwise replace the wiring.
Remove component 156 and check that there is no continuity in “Parking
brake released” position', otherwise replace component 156.
Check the connection and condition of the connector of component 247.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the connector, otherwise replace the wiring.
With the lever released, check that there is no continuity on the following
connection:
Connection 27A between component 156 and the vehicle earth.
With the lever released, check the earth insulation of:
Connection 27A between component 156 and component 247.
If there is a repair method (see Technical Note 6015A Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET097 / TDB_V08_ET097

83A-39
MR-413-X44-83A000$616.mif
V5

Vdiag No.: 04, 08INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
ET097
CONTINUED
RELEASED
STATUS
when the lever
has been
pulled up
Check the connection and condition of the connector of component 156.
Remove the handbrake switch and check the continuity is correct with the
“Parking brake applied” position.
Check the connection and condition of the connector of component 247.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the connector, otherwise replace the wiring.
With the lever pulled, check for continuity on:
Connection 27A between component 156 and the vehicle earth.
With the lever pulled, check the continuity of:
Connection 27A between component 156 and component 247.
If there is a repair method (see Technical Note 6015A Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.

83A-40
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET245
INDICATORS
NOTESCheck for the absence of faults on the indicators in the UCH field before starting
fault finding.
Vehicle under + after ignition feed.
If the indicator lights are not displayed or are inconsistent with the position of the control, carry out the following
fault finding procedure.
If status ET245 INDICATORS is INACTIVE and the control is activated:
Check that the connector of component 247 is in good condition and correctly connected.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair) repair the connector, otherwise replace the wiring.
Check the continuity of:
Connection 64C between component 645 and component 247 (left-hand indicator)
Connection 64D between component 645 and component 247 (right-hand indicator)
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET245 / TDB_V08_ET245