ignition RENAULT TWINGO 2009 2.G Electrical Equipment - Lightening Workshop Manual

80D-2
MR-413-X44-80D000$100_eng.mif
V1
80D
LIGHTING
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
To run diagnostics on the vehicle's computers, switch on the ignition in fault finding mode (+ after ignition feed).Vehicle(s): NEW TWINGO
Function concerned: Lighting
Special tooling required
Multimeter
Elé. 1681 Universal bornier
MR-413-X44-80D000$100_eng.mif

80D-3
MR-413-X44-80D000$100_eng.mif
V1
LIGHTING
Fault finding - Introduction80D
Faults
Faults are declared as either present or stored (depending on whether they appeared in a certain context and have
disappeared since, or whether they remain present but have not been diagnosed within the current context).
The present or stored status of faults should be taken into consideration when the diagnostic tool is switched on
after the + after ignition feed (without any system components being active).
For a present fault, apply the procedure described in the Interpretation of faults section.
For a stored fault, note the faults displayed and apply the instructions in the Notes section.
If the fault is confirmed when the instructions in the Notes section are applied, the fault is present. Deal with the fault
If the fault is not confirmed, check:
–the electrical lines which correspond to the fault,
–the connectors on these lines (corrosion, bent pins, etc.),
–the resistance of the component detected as faulty,
–the condition of the wires (melted or split insulation, wear).
Conformity check
The aim of the conformity check is to check data that does not produce a fault on the diagnostic tool because the
data is inconsistent. Therefore, this stage is used to:
–run diagnostics on faults that do not have a fault display, and which may correspond to a customer
complaint.
–check that the system is operating correctly and that there is no risk of a fault recurring after repairs.
This section gives the fault finding procedures for statuses and parameters and the conditions for checking them.
If a status is not behaving normally or a parameter is outside the permitted tolerance values, consult the
corresponding fault finding page.
Customer complaints - Fault finding chart
If the test with the diagnostic tool is OK but the customer complaint is still present, the fault should be processed by
customer complaint.
A summary of the overall procedure to follow is provided on the following page in the
form of a flow chart.

80D-6
MR-413-X44-80D000$100_eng.mif
V1
LIGHTING
Fault finding - Introduction80D
5. FAULT FINDING LOG
You will always be asked for this log:
–when requesting technical assistance from the Techline,
–for approval requests when replacing parts for which approval is obligatory
–to be attached to monitored parts for which reimbursement is requested. The log is needed for warranty
reimbursement, and enables better analysis of the parts removed.
6. SAFETY INSTRUCTIONS
Safety rules must be observed during any work on a component to prevent any damage or injury:
–check the battery voltage to avoid incorrect operation of computer functions,
–Use the proper tools.
Procedure for disconnecting the battery:
–switch off the ignition,
–switch off all electrical consumers,
–wait at least 1 minute for the electronic systems to switch off,
–disconnect the battery, starting with the negative terminal. IMPORTANTIMPORTANT
Any fault on a complex system requires thorough fault finding with the appropriate tools. The
FAULT FINDING LOG, which should be completed during the procedure, enables you to keep
track of the procedure which is carried out. It is an essential document when consulting the
manufacturer.
IT IS THEREFORE MANDATORY TO FILL OUT A FAULT FINDING LOG EACH TIME FAULT FINDING IS
CARRIED OUT.

80D-20
MR-413-X44-80D000$700_eng.mif
V1
80D
LIGHTING
Fault finding - Conformity check
LIGHTING FUNCTION
SUB-FUNCTION: LIGHTING CONTROL
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection
unit)1
Lighting
controlET081:Lighting switch
positionSIDE
DIPPED
MAIN BEAM
HEADLIGHTSIn the event of a fault,
refer to the interpretation
for status ET081.
2ET085:Hazard warning
lights buttonPRESSED
RELEASEDIn the event of a fault,
consult the interpretation
for status ET085.
3
Lighting
requestET115:Request to
switch on lights
by light sensorPRESENT
ABSENTIn the event of a fault,
consult the interpretation
for status ET115.
4ET111:Front fog lights
requestPRESENT
ABSENTIn the event of a fault,
refer to the interpretation
for status ET111.
5ET082:Rear fog lights
requestPRESENT
ABSENTIn the event of a fault,
refer to the interpretation
of status ET082.
6ET083:Left hand
indicator requestPRESENT
ABSENTIn the event of a fault,
consult the interpretation
of statuses ET083
and ET084. 7ET084:Right hand
indicator requestPRESENT
ABSENT
8TailgateET463:Door(s) or
tailgateOPEN
CLOSEDIn the event of a fault,
consult the interpretation
for status ET0463.
9Vehicle
speedPR008:Vehicle speed0 mphIn the event of a fault,
carry out fault finding on
the ABS (see 38C, ABS
and 87B, Passenger
compartment
connection unit).
MR-413-X44-80D000$700_eng.mif

80D-21
MR-413-X44-80D000$700_eng.mif
V1
LIGHTING
Fault finding - Conformity check80D
SUB-FUNCTION: LIGHTING OUTPUT
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection
unit)1Front fog
lightsAC008:Front fog
lightsThis command is
used to activate
the front fog lightIn the event of a fault,
apply the procedure
for DF108 (see 87B,
UCH).
2Rear fog
lightsAC009:Rear fog
lightsThis command is
used to activate
the rear fog lightIn the event of a fault,
apply the procedure
for DF109 (see 87B,
UCH).
3
Direction
indicatorsAC022:Left hand
direction
indicatorsThis command is
used to activate
the left hand
direction
indicators.In the event of a fault,
refer to the
interpretation of
fault DF013 "Left-
hand indicator
circuit" (see 87B,
UCH).
4AC023:Right hand
direction
indicatorsThis command is
used to activate
the right hand
direction
indicators.In the event of a fault,
refer to the
interpretation of
fault DF012 "Right-
hand indicator
circuit" (see 87B,
UCH).
5
LightsAC055:Side lightsThis command
enables the side
lights to be
activated.In the event of a fault,
apply the procedure
for DF087 (see 87B,
UCH).
6AC054:Dipped
headlightsThis command
enables the
dipped
headlights to be
activated.In the event of a fault,
apply the procedure
for DF088 (see 87B,
UCH).
7AC062:Main beam
headlightsThis command
enables the main
beam headlights
to be activated.In the event of a fault,
apply the procedure
for DF098 (see 87B,
UCH).

80D-22
MR-413-X44-80D000$700_eng.mif
V1
LIGHTING
Fault finding - Conformity check80D
SUB-FUNCTION: LIGHTING OUTPUT (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)8LightsAC063:Gradual lighting
and dimming of
the courtesy
lightThis command is
used to check that
the courtesy light
gradual lighting and
dimming function is
operating correctly.In the event of a
fault, apply the
procedure for
DF139 (see 87B,
UCH).
9Temperature
displayAC110:Temperature
displayControls the display.In the event of a
fault, apply the
procedure for
command
AC110 (see 87B,
UCH).

80D-23
MR-413-X44-80D000$800_eng.mif
V1
80D
LIGHTING
Fault finding - Customer complaints
NOTESOnly refer to these customer complaints after performing a complete check with
the diagnostic tool.
LIGHTING80D
NO REAR FOG LIGHTS ALP 2
NO RIGHT HAND DIRECTION INDICATOR ALP 3
NO LEFT HAND DIRECTION INDICATOR ALP 4
NO SIDE LIGHTS ALP 5
NO DIPPED HEADLIGHTS ALP 6
NO HEADLIGHTS ALP 7
NO FRONT FOG LIGHTS ALP 8
LIGHTS NOT SWITCHING OFF AFTER + AFTER IGNITION FEED IS CUT
AND DRIVER'S DOOR IS OPENEDALP 9
LIGHTS NOT SWITCHING ON AT NIGHT ALP 10
NO SEE-ME-HOME LIGHTING ALP 11
NO COURTESY LIGHTS ALP 12
MR-413-X44-80D000$800_eng.mif

80D-39
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 9Lights are not switched off after switching off the + after ignition
feed and the driver's door opening
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check, as a priority, the operation of status ET115 "Request to switch on the lights
via the light sensor" and commands AC054 Dipped headlights and AC055 Side
lights in the UCH.
Note:
For the lights to switch off automatically after driving, the following conditions must all be met:
–engine stopped,
–ignition: 0 (inactive),
–vehicle speed > 0 mph (0 km/h),
–driver's door: closed.
Carry out a multiplex network test. If the multiplex
network contains faults (see 88B, Multiplexing).
Check the operation of status ET142 "Engine
operating phase".
Is the status functioning correctly?
YES
Make sure that status ET239 Ignition switch
position is working.
Is the status functioning correctly?
YES
NOApply the procedure for processing status
ET142.
NOApply the procedure for processing status
ET239.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP9

80D-43
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 11 No See-me-home lighting
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check whether the vehicle has a rain/light sensor. If the vehicle does not have a rain/light sensor, explain to the
customer that this is normal, and that the vehicle does not have this feature.
Check that LC025 "See-me-home lighting" is "With", otherwise use CF032 "See-me-home lighting".
Check that the ignition is switched off.
Flash the headlights one or more times (as required) to activate the See-me-home lighting function.
Check that the horn and lights switch is operating correctly using status ET081 "Lighting stalk position". In the
event of a fault with the horn and lights switch, refer to the interpretation of status ET081 "Lighting stalk
position".
Use the following commands to check that the side lights, dipped headlights and main beam headlights are
operating correctly.
–AC055 "Side lights",
–AC054 "Dipped headlights",
–AC062 "Main beam headlights".
In the event of a fault, refer to the interpretation of the following faults:
–DF087 "Side lights relay control circuit",
–DF088 "Dipped headlights relay control circuit",
–DF098 "Main beam headlights relay control circuit".
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP11