diagram RENAULT TWINGO 2009 2.G Electrical Equipment - Multimedia Connection Workshop Manual

8Electrical equipment
V1 MR-413-X44-86C000$TOC.mif
V1
86C
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
V1
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s. 2009
MULTIMEDIA CONNECTION
CBOX
Vdiag No.: 04
Fault finding – Introduction 86C - 2
Fault finding – List and location of components 86C - 8
Fault finding – Role of components 86C - 14
Fault finding – Operating diagram 86C - 15
Fault finding – Function 86C - 18
Fault finding – Configuration 86C - 19
Fault finding – Programming 86C - 20
Fault finding – Fault summary table 86C - 21
Fault finding – Interpretation of faults 86C - 22
Fault finding – Conformity check 86C - 32
Fault finding – Status summary table 86C - 33
Fault finding – Parameter summary table 86C - 34
Fault finding – Command summary table 86C - 35
Fault finding – Customer complaints 86C - 36
Fault finding – Fault Finding Chart 86C - 37

86C -2V1 MR-413-X44-86C000$010.mif
86C
CBOX
Vdiag No.: 04
1. APPLICABILITY OF THE DOCUMENT
This document presents the fault finding method applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
Fault finding procedure
To run fault finding on the vehicle computers, switch on the ignition.
Depending on the type of vehicle equipment, proceed as follows:Vehicle(s): New Twingo and Clio IIIComputer name: Mobile connectivity (CBOX)
Function concerned: Multimedia connectionVdiag No.: 04
Special tooling required
Diagnostic tool
Multimeter
Elé. 1681 Universal bornier
For vehicles with key-operated/radio frequency remote control, use the key to switch on the ignition.
For vehicles with Renault cards,
–with the vehicle card in the card reader,
–press and hold the start button (+5 seconds) outside starting conditions, connect the diagnostic tool, and carry
out the desired operations.
CBOX_V04_PRELI
MULTIMEDIA CONNECTION
Fault finding – Introduction

86C-15V1 MR-413-X44-86C000$040.mif
86C
CBOX
Vdiag No.: 04
I. LIST OF COMPONENTS
Number Description Number Description
1Radio 9Mobile connectivity terminal (digital /
analogue)
2Diagnostic socket 10 Rear right-hand speaker
3Display 11 Rear left-hand speaker
4Supply 12 Front right-hand speaker
5Radio control satellite 13Front right-hand tweeter (depending on
equipment).
6Earth 14 Front left-hand speaker
7 Mobile connectivity terminal (RCA type) 15Front left-hand tweeter (depending on
equipment).
8Mobile connectivity computer 16 Aerial
MULTIMEDIA CONNECTION
Fault finding – Operating diagram

86C-16V1 MR-413-X44-86C000$040.mif
MULTIMEDIA CONNECTION
Fault finding – Operating diagram86C
CBOX
Vdiag No.: 04
II. LOCATION OF COMPONENTS
New Twingo
23
CAN V
CAN M4
5 4
6
1
7
8
94 16
15
14
13
12
11
10

86C-17V1 MR-413-X44-86C000$040.mif
MULTIMEDIA CONNECTION
Fault finding – Operating diagram86C
CBOX
Vdiag No.: 04
Clio III
16
15
14
13
12
11
107 9 8
45 4 3
2
4
6
1CAN M CAN V

86C-25
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86C000$090.mif
MULTIMEDIA CONNECTION
Fault finding – Interpretation of faults86C
CBOX
Vdiag No.: 04
DF004
PRESENT
OR
STOREDBATTERY VOLTAGE
1.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The + after ignition feed is activated,
–The multimedia system is switched on using the on/off button.
–The battery voltage is out of range (12 V < X < 15 V).
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the conformity of the fuse of the fuse and relay box (use the Wiring Diagrams Technical Note for Clio III
or New Twingo):
–for New Twingo: F48 (15A),
–for Clio III: unit fuse 710 (15A) and F2 (20A) on component 260.
Replace the fuse if not correct.
Disconnect the connector of the mobile connectivity computer, component code 1959.
Check the continuity of the earth on connection NAM.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
CBOX_V04_DF004

86C-28
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86C000$090.mif
MULTIMEDIA CONNECTION
Fault finding – Interpretation of faults86C
CBOX
Vdiag No.: 04
DF006
PRESENT
OR
STOREDDIGITAL TERMINAL CONNECTION
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system was switched on using the
radio on/off button.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check the connection and condition of the connectors of the mobile connectivity computer, component code
1959 and of the mobile connectivity terminal, component code 1877.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the computer connector and check the insulation, continuity and the absence of interference
resistance on the following connections:
–34PE between components 1959 and 1877,
–34PH between components 1959 and 1877,
–34PG between components 1959 and 1877,
–34PJ between components 1959 and 1877,
–34TE between components 1959 and 1877,
–34TJ between components 1959 and 1877,
–34TH between components 1959 and 1877,
–34TG between components 1959 and 1877.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
CBOX_V04_DF006

86C-31
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86C000$090.mif
MULTIMEDIA CONNECTION
Fault finding – Interpretation of faults86C
CBOX
Vdiag No.: 04
DF008
PRESENT
OR
STOREDUSB SUPPLY
CC.0: Short circuit to earth
1.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system was switched on using the
radio on/off button.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check the connection and condition of the connectors of the mobile connectivity computer, component code
1959 and of the mobile connectivity terminal, component code 1877, depending on the vehicle equipment.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the computer connector and check the insulation, continuity and the absence of interference
resistance on the following connections:
–34TE between components 1959 and 1877,
–34TG between components 1959 and 1877.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Replace the mobile connectivity terminal (see MR 392 (Clio III) or MR 411 (New Twingo) 86A, Radio, Offset
audio socket: Removal – Refitting).
If the fault is still present, contact Techline.
CBOX_V04_DF008

86C-37
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86C000$150.mif
86C
CBOX
Vdiag No.: 04
ALP 1 No dialogue with the computer
NOTESTry to establish dialogue with a computer on another vehicle to check that the
diagnostic tool is not faulty. If the diagnostic tool is not causing the fault and dialogue
cannot be established with any other computer on the same vehicle, it may be that a
faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations
to obtain the correct voltage (12 V < X < 15 V).
Ensure that the communication conditions are present: + After ignition feed and radio
on/off button pressed.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
If the vehicle is equipped with a navigation computer, the mobile connectivity computer
is connected to the navigation computer, component code 662, otherwise it is
connected to the radio, component code 261.
CBOX_V04_ALP1
MULTIMEDIA CONNECTION
Fault finding – Fault Finding Chart

86C-42
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86C000$150.mif
MULTIMEDIA CONNECTION
Fault finding – Fault Finding Chart86C
CBOX
Vdiag No.: 04
ALP 2 My USB peripheral cannot be read
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
If an error message appears, consult the Internet site, renault.net, to check the
compatibility of the USB peripheral.
If the vehicle is equipped with a navigation computer, the mobile connectivity computer
is connected to the navigation computer, component code 662, otherwise it is
connected to the radio, component code 261.
Test the compatibility of another USB key,
which is Renault compatible, with the mobile
connectivity terminal.Explain to the customer that the USB key
is faulty or that it is not compatible with the
mobile connectivity.
Is the USB key read correctly?
Check the appearance of the receiver
connections of the USB key on the mobile
connectivity terminal.
Are the connections in good condition?Replace the mobile connectivity terminal,
component code 1877 (see MR 392 (Clio
III) or MR 411 (New Twingo) 86A,
Radio, Mobile connectivity terminal:
Removal – Refitting).
YES
NO
NO
NO
A
CBOX_V04_ALP2