RENAULT TWINGO 2009 2.G Electrical Equipment - Radio R2-08 Owner's Manual

86A-21V1 MR-413-X44-86A150$020.mif
RADIO
Fault finding – List and location of components86A
R2-08
Vdiag No.: 64
Front left-hand tweeter (fitted depending on equipment)
Rear view of the mobile connectivity terminal

86A-22V1 MR-413-X44-86A150$030.mif
86A
R2-08
Vdiag No.: 64
Role of main components
The radio computer manages the various multimedia system functions according to user requests and transmits
audio data to the vehicle via the speakers.
The radio uses an amplified aerial system to improve radio reception.
The aerial amplifier is incorporated into the roof aerial.
The speakers reproduce the radio system's sound inside the vehicle.
The microphone allows the telephone to be used in hands-free mode via a Bluetooth connection.
The tweeters reproduce the high-frequency sounds of the radio system.
The multimedia interface unit (Display or Multimedia connection unit) receives various signals from the vehicle
CAN (speed, status of exterior lights) and retransmits them for the radio via the Multimedia CAN.
The multimedia interface unit (Display or Multimedia connection unit) transmits the activation signal to the radio and
to the other computers that participate in the multimedia function when the user activates the radio button.
The display shows various multimedia information such as the radio information, the time, etc.
The radio control satellite allows various functions of the radio to be accessed.
RADIO
Fault finding – Role of components

86A-23V1 MR-413-X44-86A150$040.mif
86A
R2-08
Vdiag No.: 64
I. LIST OF COMPONENTS
Number Description Number Description
1Radio 10 Rear right-hand speaker
2Diagnostic socket 11 Rear left-hand speaker
3Display 12 Front right-hand speaker
4Supply 13Front right-hand tweeter
(depending on equipment).
5Radio control satellite 14 Front left-hand speaker
6Earth 15Front left-hand tweeter
(depending on equipment)
7 Mobile connectivity terminal
(RCA type)16 Aerial
8Mobile connectivity computer (C-Box) 17 Microphone
9Mobile connectivity terminal (digital /
analogue)
RADIO
Fault finding – Operating diagram

86A-24V1 MR-413-X44-86A150$040.mif
RADIO
Fault finding – Operating diagram86A
R2-08
Vdiag No.: 64
II. LOCATION OF COMPONENTS
New Twingo
13
15
16
14
12
6
7
10
11
5
2
4
3
1CAN M
CAN V
4
17
8
9
4

86A-25V1 MR-413-X44-86A150$040.mif
RADIO
Fault finding – Operating diagram86A
R2-08
Vdiag No.: 64
For Clio III
13
15
16
14
12
6
8
10
11
5
2
4
3
1CAN M
CAN V
4
179
7
4

86A-26V1 MR-413-X44-86A150$050.mif
86A
R2-08
Vdiag No.: 64
The radio includes the following functions:
•Radio reception (AM, FM).
•CD/MP3 playing.
•Hands-free for Bluetooth telephones.
•Voice recognition for telephone functions
•Audio reading of a Bluetooth peripheral (Telephone for example).
The system offers the following possibilities:
•Choose FM radio stations using the presets, the list or manual selection.
•Have access to an automatically updated FM radio list.
•Listen to CDs and MP3s.
•Control the radio using the radio control satellite.
•Have access to optimised audio and acoustic telephone configurations for each vehicle according to the vehicle
type.
•Modify various acoustic parameters (base, treble, front/rear balance, etc.).
•Use the hands-free telephone function (sound relayed towards the radio speakers) with a Bluetooth telephone.
•Use voice recognition for the telephone functions (button on the radio control satellite). The voice identifier can be
recorded.
•Benefit from a connection for a CD changer.
•Possibility of connecting a peripheral with a USB port, Jack socket, etc.
•Anti-theft protection
Computer activation system
The radio has an activation system.
The radio is switched on under the following conditions:
•by pressing the radio ON/OFF button,
•when the engine is started, the radio is switched on automatically.
The radio is switched off under the following conditions:
•The ignition is switched off.
•Door opened (Clio III)
•1 minute after a door is opened (New Twingo)
•By pressing the radio ON/OFF button (Clio III and New Twingo).
In the last case, if the vehicle engine is running, the radio will be switched off from a user point of view, but will be
considered operational from an electrical point of view. If the ignition is switched off, the radio will be off.
The multimedia interface unit (Display or Multimedia connection unit) is activated by the UCH (central door
unlocking); this then activates the multimedia computers (Navigation, Radio, etc.) via the "Activation signal"
connections.
RADIO
Fault finding – Function

86A-27V1 MR-413-X44-86A150$060.mif
86A
R2-08
Vdiag No.: 64
Thermal protection
Thermal protection is integrated in order to protect the radio.
The functions are restored when the internal temperature falls below 80˚C.
Car radio code
The radio is protected by a two-part anti-theft system:
•A 4-digit code,
•Information exchanged between the instrument panel and the radio.
This code is requested in the following cases:
•New vehicle,
•New radio,
•When a radio is swapped between vehicles.
Entering the code using the radio control satellite:
Press the lower button on the radio control satellite to confirm an entry.
Entering using the radio:
Enter the digits using buttons 1, 2, 3 and 4, and then confirm with button 6.
If the code is entered incorrectly, the radio will be locked (1 minute for the first error, 2 minutes for the second error,
4 minutes for the third error, etc., for a maximum of 32 minutes after each attempt).
After several attempts, if the fault is still present, contact the Techline.
Reminder:
The radio will operate for approximately 2 minutes in scrambled mode without the code having been entered
(with regular warning beeps).
Note:
If the battery is disconnected, it is not necessary to re-enter the radio anti-theft code.
RADIO
Fault finding – Anti-theft code

86A-28V1 MR-413-X44-86A150$070.mif
86A
R2-08
Vdiag No.: 64
The pre-code is recovered by consulting ID007 Radio programming key using the diagnostic tool or by removing
the radio and noting the four characters on the barcode following the letter T (see photo below).
There are three ways to recover the radio code (4 digits):
1. Only the VIN is available: connect to code management on Renault.Net and enter the VIN. The code server
gives the original radio code entered in the World Vehicle Database (BVM).
If the code has not been entered in the BVM or is incorrect when the code is entered in the radio, follow the
procedure below:
2.The pre-code is available: go back to code management on Renault.Net, enter the pre-code and obtain the radio
code.
If this code is correct, the radio will operate again; if not, follow the procedure below:
3. On Renault.Net, write a help message to be sent to the assistance unit.
WHEN REPLACING PARTS, OR FOR AN UNKNOWN VIN, WRITE A HELP MESSAGE IN CODE
MANAGEMENT ON RENAULT.NET TO UPDATE THE DATABASE.
RADIO
Fault finding – Anti-theft code recovery procedure

86A-29V1 MR-413-X44-86A150$080.mif
86A
R2-08
Vdiag No.: 64
Available configuration and operating mode
SC002: Computer configuration
This command is used to configure the computer according to the vehicle equipment, type of driving and language.
Configuration modification procedure:
•Activate the + after ignition feed.
•Connect the diagnostic tool and switch on the radio.
•Establish dialogue with the computer.
•Select the Repair mode menu.
•Select the Configuration and programming menu.
•Select the special command SC002 Computer configuration.
•Select the connection in the drop-down menu that corresponds to the vehicle.
•Click on Confirm.
•Exit diagnostic mode (ends dialogue with the computer without switching off the tool), switch off the ignition for
30 seconds and then switch the ignition back on.
•Establish dialogue with the computer.
•Check to see that the configurations have been correctly stored in the Configuration reading menu.
NOTE:
To reconfigure the computer, delete any telephones already paired to the radio (using the menus, see the user's
manual), before running configuration SC002 Computer configuration.
RADIO
Fault finding – Configurations

86A-30V1 MR-413-X44-86A150$090.mif
86A
R2-08
Vdiag No.: 64
VP001: Write VIN
This command enables the vehicle identification number to be entered manually in the computer. Use this command
each time the computer is replaced. The VIN is stamped on the manufacturer's plate.
Procedure for entering the VIN
•Establish dialogue with the navigation computer.
•Select the Repair mode menu.
•Select the Other configuration menu.
•Select line VP001 Write VIN.
•Enter the VIN.
•Exit fault finding mode.
•Switch off the ignition.
•Wait for the end of the Powerlatch* phase (20 minutes maximum).
•Reread the VIN in the Identification menu to confirm ID014 VIN code.
VP003: Enter After-Sales operation date
This command is used to enter the date of the last After-Sales operation on the radio.
Consecutively enter the six figures of the date: two for the year, two for the month and two for the day.
E.g. 000706 (6 July 2000).
Reread the date of the last After-Sales operation in the Identification menu to confirm ID005 Last After-Sales
operation date.
*Powerlatch: Time required for injection computer supply after + 12 V after ignition feed cut-off.
RADIO
Fault finding – Programming