warning light RENAULT TWINGO 2009 2.G Electrical Equipment Owner's Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO, Model: RENAULT TWINGO 2009 2.GPages: 241
Page 214 of 241
88A-78
WIRING HARNESS
Rear bumper wiring: Removal - Refitting
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the rear bumper (see Rear bumper: Re-
moval - Refitting) (MR 412, 55A, Exterior protec-
tion).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
a
aDisconnect the license plate light connectors.aDisconnect the rear proximity radar connectors (1) .
a
aRemove the rear bumper wiring.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIf replacing with more wiring, lock the unused con-
nectors (see Connector: Sealing and immobilisa-
tion) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the rear bumper wiring.
aConnect the rear proximity radar connectors.
aConnect the number plate light connectors. IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
121371
WARNING
To prevent any risk of noise, premature wear,
short circuits, etc. after the refitting operation,
mark the wiring routing and how to connect the
connectors.
REAR PROXIMITY RADAR
121371
WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
REAR PROXIMITY RADAR
Page 216 of 241
88C-1
AIR BAG AND PRETENSIONERS
Airbag and pretensioners: Precautions for the repair
88C
I - PRECAUTIONS FOR REPAIR
When working underneath the vehicle (on the bo-
dywork, sill panel, etc.) or for certain operations invol-
ving removal or refitting of seat trims, it is essential to
lock the airbag computer using the Diagnostic tool
and to disconnect the battery (see 80A, Battery, Bat-
tery: Removal - Refitting, page 80A-2) .The pyrotechnic systems (pretensioners and airbags)
must be checked using the Diagnostic tool :
-after an accident,
-after theft or attempted theft of the vehicle,
-before selling a used vehicle.
II - TRIGGERING OF THE SAFETY SYSTEMS
After detection of an impact, the airbag computer locks
definitively and the « airbag fault » warning light is illu-
minated on the instrument panel. The airbag computer
and the side impact sensors must always be replaced.
III - DURABILITY OF THE PYROTECHNIC
COMPONENTS
The precautions which recommended that pyrotechnic
components (airbags and pretensioners) were repla-
ced 10 years after the registration of the vehicle have
now been lifted.
Pyrotechnic components (airbags and pretensioners)
do not therefore require any maintenance. Equipment required
Diagnostic tool
IMPORTANT
All operations on airbag and pretensioner systems
must be carried out by qualified trained personnel.
The airbags have a pyrotechnic gas generator, with
an ignition module and bag which must not be
separated.
The pretensioners have a pyrotechnic gas genera-
tor and an igniter which must, under no circumstan-
ces, be separated.
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
IMPORTANT
To prevent any accidental triggering whilst w orking
on or near a pyrotechnic component (airbags or
pretensioners), lock the airbag computer using the
Diagnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
(see Fault finding - Replacement of compo-
nents) (88C, Airbag and pretensioners).
IMPORTANT
To prevent the pyrotechnic components from being
permanently deactivated or triggered (airbags or
pretensioners), check the airbag computer using
the Diagnostic tool.
IMPORTANT
In order to prevent interference with the deployment
of the airbags:
-do not fit a cover to the front seats,
-do not place objects in the area of deployment.
IMPORTANT
To eliminate the risk of any accident, do not reuse
pyrotechnic components.
It is essential to destroy pretensioners or airbags
before scrapping a vehicle or a part only (see 88C,
Air bag and Pretensioners, Airbags and preten-
sioners: Recycling - Destruction, page 88C-2) .
Page 221 of 241
88C-6
AIR BAG AND PRETENSIONERS
Driver's frontal airbag: Removal - Refitting
88C
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aLock the airbag computer using the Diagnostic tool
(see MR 413 Fault finding, 88C, Airbags and seat
belt pretensioners, Fault finding - Replacement
of components).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aTurn the steering wheel one half-turn.aRemove the driver's front airbag by opening (1) the
clips (2) using a flat-blade screwdriver. Equipment required
Diagnostic tool
IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Air-
bag and pretensioners: Precautions for the
repair, page 88C-1) .
IMPORTANT
To avoid any risk of triggering when working on
or near a pyrotechnic component (airbags or pre-
tensioners), lock the airbag computer using the
diagnostic tool.
When this function is activated, all the trigger
lines are inhibited and the airbag warning light on
the instrument panel lights up continuously (igni-
tion on).
IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.
119481
119496
Page 223 of 241
88C-8
AIR BAG AND PRETENSIONERS
Passenger's frontal airbag: Removal - Refitting
88C
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aOpen the dashboard glovebox.
aUnclip the access flap (1) to the passenger's front
airbag connector.
aRemove:
-the nuts (2) of the tie rod between the bulkhead
and the dashboard cross member, Equipment required
Diagnostic tool
Tightening torquesm
passenger front airbag
nuts21 Nm
nuts of the tie rod side
on the bulkhead side8 Nm
IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Air-
bag and pretensioners: Precautions for the
repair, page 88C-1) .
IMPORTANT
To avoid any risk of triggering when working on
or near a pyrotechnic component (airbags or pre-
tensioners), lock the airbag computer using the
diagnostic tool.
When this function is activated, all the trigger
lines are inhibited and the airbag warning light on
the instrument panel lights up continuously (igni-
tion on).
IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.
119519
K9K – D4F, and 780
127744
Page 226 of 241
88C-11
AIR BAG AND PRETENSIONERS
Front (chest-level) side airbag: Removal - Refitting
FRONT SIDE AIRBAG, and REAR AIRBAG 01
88C
The front chest airbag is fixed to the lower section of
the seatback of each front seat on the door side.
When it is deployed, the inflatable bag tears the modu-
le cover and the foam and detaches the trim.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the complete front seat (see Complete front seat:
Removal - Refitting) (MR 412, 75A, Front seat fra-
mes and runners),-the front seat seatback trim (see Front seatback
trim: Removal - Refitting) (MR 412, 77A, Front
seat trim). Equipment required
Diagnostic tool
IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Air-
bag and pretensioners: Precautions for the
repair, page 88C-1) .
IMPORTANT
To prevent any accidental triggering whilst wor-
king on or near a pyrotechnic component (air-
bags or pretensioners), lock the airbag computer
using the Diagnostic tool.
When this function is activated, all the trigger
lines are inhibited and the airbag warning light on
the instrument panel lights up continuously (igni-
tion on).
IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.
Page 229 of 241
88C-14
AIR BAG AND PRETENSIONERS
Side curtain airbag: Removal - Refitting
FRONT SIDE AIRBAG, and REAR AIRBAG 01
88C
The side curtain airbag is mounted behind the headli-
ning.
The airbag detaches the headlining when it inflates.
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the front seat belt upper bolt (see Front seat belt:
Removal - Refitting) (MR 412, 59A, Safety equip-
ment),-the rear seat belt upper bolt (see Rear seat belt:
Removal - Refitting) (MR 412, 59A, Safety equip-
ment),
-the sun visors (see Sun visor: Removal - Refit-
ting) (MR 412, 57A, Interior equipment),
-the interior rear-view mirror covers (see Interior
rear-view mirror: Removal - Refitting) (MR 412,
57A, Interior equipment),
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the rear parcel shelf side trims (see Rear parcel
shelf side trim: Removal - Refitting) (MR 412,
71A, Body internal trim),
-the rear panel trims (see Rear panel lining: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the rear quarter panel trims (see Quarter panel
trim: Removal - Refitting) (MR 412, 71A, Body in-
ternal trim),
-the B-pillar upper trims (see B-pillar upper trim:
Removal - Refitting) (MR 412, 71A, Body internal
trim),
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim). Equipment required
Diagnostic tool
Tightening torquesm
curtain airbag bolt8 Nm
IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Air-
bag and pretensioners: Precautions for the
repair, page 88C-1) .
IMPORTANT
To prevent any accidental triggering whilst wor-
king on or near a pyrotechnic component (air-
bags or pretensioners), lock the airbag computer
using the Diagnostic tool.
When this function is activated, all the trigger
lines are inhibited and the airbag warning light on
the instrument panel lights up continuously (igni-
tion on).
IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.
Page 233 of 241
88C-18
AIR BAG AND PRETENSIONERS
Side impact sensor: Removal - Refitting
FRONT SIDE AIRBAG, and REAR AIRBAG 01
88C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the complete front seat (see Complete
front seat: Removal - Refitting) (MR 412, 75A,
Front seat frames and runners).Equipment required
Diagnostic tool
Tightening torquesm
impact sensor bolt8 Nm
IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Air-
bag and pretensioners: Precautions for the
repair, page 88C-1) .
IMPORTANT
To prevent any accidental triggering whilst wor-
king on or near a pyrotechnic component (air-
bags or pretensioners), lock the airbag computer
using the Diagnostic tool.
When this function is activated, all the trigger
lines are inhibited and the airbag warning light on
the instrument panel lights up continuously (igni-
tion on).
Page 236 of 241
88C-21
AIR BAG AND PRETENSIONERS
Front buckle pretensioner: Removal - Refitting
88C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the complete front seat (see Complete
front seat: Removal - Refitting) (MR 412, 75A,
Front seat frames and runners).aRemove:
-the front seat casing bolt (1) ,
-the front seat casing at (2) and (3) . Equipment required
Diagnostic tool
Tightening torquesm
front buckle pretensio-
ner bolt35 Nm
IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Air-
bag and pretensioners: Precautions for the
repair, page 88C-1) .
IMPORTANT
To prevent any accidental triggering whilst wor-
king on or near a pyrotechnic component (air-
bags or pretensioners), lock the airbag computer
using the Diagnostic tool.
When this function is activated, all the trigger
lines are inhibited and the airbag warning light on
the instrument panel lights up continuously (igni-
tion on).
IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.
120846
Page 240 of 241
88C-25
AIR BAG AND PRETENSIONERS
Inhibitor switch: Removal - Refitting
88C
II - FINAL OPERATION.
aCheck:
- the operation of the switch,
- the “airbag off” warning light on the instrument pa-
nel.