stop start RENAULT TWINGO 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Workshop Manual

87B-10
MR-413-X44-87B000$192.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Role of components87B
–Energy management function
Role of BSS connection:
This bidirectional connection located between the UCH and the alternator circulates the following signals:
–Signals sent by the alternator: rotor current value, alternator charge value and electrical, thermal and
mechanical fault statuses.
–Signals sent by the UCH to the alternator: voltage setpoint, rail setpoint and rail inhibition.
Role of the DF terminal:
The signal circulating in the DF terminal is the alternator charge signal (displayed using PR073 "Alternator
charge signal") which is used to adapt the alternator supply to the demands of the electrical consumers
(such as the passenger compartment heating resistors, heated rear screen, etc.).
Depending on the battery charge status, the operating phase and the battery temperature, the UCH determines what
the voltage across the battery terminals should be.
When the battery charge drops, and PR076 Battery voltage after rest decreases, the UCH can temporarily
increase PR075 Alternator setpoint voltage by 1 V for a period of 15 minutes after switching on + after ignition
feed.
Before and during starting, PR075 Alternator setpoint voltage is fixed at 10.7 V.
A maximum of 30 seconds after the engine has started, the UCH sets PR075 Alternator setpoint voltage to the
optimum value calculated.
The injection computer can also control the alternator regulation voltage. The injection computer sends the
maximum authorised power delivered by the engine, to the UCH via the multiplex network. If this power supplied by
the engine is less than the power consumed by the alternator, the UCH reduces the PR075 Alternator setpoint
voltage.
The battery warning light will flash if a low battery charge is detected (no-load voltage less than 12.2 V: voltage
measured during technical use) for the first 12 miles (20 kms), then the warning light stops flashing. Also, the magic
eye of the battery (the hydrometer) is black.
–Access - Security function (see 82D, Access - Security, Role of components).
–Heating and manual air conditioning function (see 61A, Heating, Role of components and 62C, Manual air
conditioning, Role of components).
–Wiping function (see 85A, Washing wiping, Role of components).
–Lighting function (see 80D, Lighting, Role of components). Note:
At the time of user activation, if the mileage is less than 12 miles (20 kms) the charge status is used to display a
warning: this ensures that vehicles are delivered with correct batteries.

87B-68
MR-413-X44-87B000$480.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Electrical suppliesPR001:Battery voltage9 V < X < 16 VIn the event of a fault, run fault
finding on the charging
circuit (see 80A, Battery).
Ignition switch positionET239:Ignition switch
position+ after ignition feed.In the event of a fault, refer to
the interpretation of status
ET239.
Brake pedalET047:Brake pedal positionDEPRESSED
RELEASEDIn the event of a fault, refer to
the interpretation of status
ET047.
Engine operation.ET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, consult
the interpretation of status
ET142.
Engine speedPR025:Engine speed0 rpmIn the event of a fault, run fault
finding on the injection
system (see 13B, Diesel
injection or 17B, Petrol
injection).
Vehicle speedPR008:Vehicle speed0 mphIn the event of a fault, run fault
finding on the ABS system
(see 38C, Anti-lock braking
system).
UCH_V44_CCONF
MR-413-X44-87B000$480.mif
UCH
Vdiag No.: 44

87B-69
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: PROTECTION
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
Engine
immobiliserET046:Engine immobiliserINACTIVE = Vehicle
unprotected, ready to start.
ACTIVE = Vehicle protected,
starting impossible.In the event of a fault, refer to
the interpretation of status
ET046.
And (see 87B, Passenger
compartment
connection unit).
ET008:blank UCHYES = If the UCH is blank.
NO = If the UCH has been
programmed with an
immobiliser code.In the event of a fault, refer to
the interpretation of status
ET008.
And (see 87B, Passenger
compartment
connection unit).
KeyET185:Key code receivedYES = If the UCH has received
the immobiliser code from the
key.
NO = If the UCH does not
receive the immobiliser code
from the key.In the event of a fault, refer to
the interpretation of status
ET185.
And (see 87B, Passenger
compartment
connection unit).
ET181:Key allocated to the
vehicleYES = The key is allocated to
the vehicle.
NO = The key is not allocated
to the vehicle.In the event of a fault, refer to
the interpretation of status
ET181.
And (see 87B, Passenger
compartment
connection unit).

87B-70
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: PROTECTION (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
KeyET045:Radio frequency
signal receivedYES = When the UCH receives
a radiofrequency signal.
NO = When the UCH does not
receive a Radiofrequency
signal.In the event of a fault, refer to
the interpretation of status
ET045.
ET193:Radiofrequency
signal from a key
allocated to the
vehiclePRESENT =
Reception of a signal
Radiofrequency signal from a
key allocated to the vehicle.
ABSENT =
No reception of signal
Radiofrequency or signal
Radiofrequency signal from a
key not allocated to the vehicleIn the event of a fault, refer to
the interpretation of status
ET193.
ET240:Key frequency (in
MHz)433
NONEIf NONE, refer to the
interpretation of status
ET240.
PR056:Number of keys
allocatedX ≤ 4 key(s)In the event of a fault, refer to
the interpretation of fault
PR056.
InjectionET229:Injection immobiliser
codePROGRAMMED
NOT PROGRAMMED
UNDETERMINEDIn the event of a fault, consult
the interpretation of status
ET229.
ET250:InjectionNOT PROTECTED
PROTECTEDIn the event of a fault, refer to
the interpretation of status
ET250.
(See 17B, Petrol Injection,
Conformity check,
Protection) or (see 13B,
Diesel Injection, Conformity
check, Protection).
Starter actuatorET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition feed.
+ START FEEDIn the event of a fault, refer to
the interpretation of status
ET239.

87B-73
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: STARTING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
EngineET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition feed.
+ START FEEDIn the event of a fault, refer to the
interpretation of status ET239.
(See 17B, Petrol Injection,
Conformity check, Protection) or
(see 13B, Diesel Injection,
Conformity check, Protection).
ET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, refer to the
interpretation of status ET142.
(See 17B, Petrol Injection,
Conformity check, Protection) or
(see 13B, Diesel Injection,
Conformity check, Protection).
PR025:Engine speed0 rpmIn the event of a fault, carry out a fault
finding on the multiplex network
(see 88B).
(See 17B, Petrol Injection,
Conformity check, Protection) or
(see 13B, Diesel Injection,
Conformity check, Protection).

87B-75
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
FUNCTION: AIR CONDITIONING
SUB-FUNCTION: HEATING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
HeatingET015:Passenger
compartment
blowerRUNNING
STOPPEDIn the event of a fault, consult the
interpretation of status ET015.
ET239:Ignition switch
position+ after ignition feed.
STARTING
ACCESSORIES FEEDIn the event of a fault, refer to the
interpretation of status ET239.
PR025:Engine speed0 rpmIn the event of a fault, carry out a fault
finding on the multiplex network
(see 88B).
And (see 17B, Petrol Injection,
Conformity check, Protection) or
(see 13B, Diesel Injection,
Conformity check, Protection).
PR001:Battery voltage9 V < X < 16 VIn the event of a fault, run fault finding
on the charging circuit (see 80A,
Battery).
PR002:External
temperature˚CIn the event of a fault, refer to the
interpretation of parameter PR002.
PR024:Engine coolant
temperature˚CIn the event of a fault (see 17B,
Petrol Injection, Conformity check,
Protection) (see 13B, Diesel
Injection, Conformity check,
Protection).
AC060:Rear screen de-
icerThis command is used to
test the operation of the
rear screen de-icer.In the event of a fault, refer to the
interpretation of command AC060.
AC110:Temperature
displayImportant: this command
lasts approximately
30 seconds.
This command is for testing
the display.In the event of a fault, refer to the
interpretation of command AC110.

87B-76
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
FUNCTION: AIR CONDITIONING
SUB-FUNCTION: COLD LOOP
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Cold loopPR002:External
temperature˚CIn the event of a fault, refer to the
interpretation of parameter
PR002.
ET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, refer to the
interpretation of status ET142.
ET015:Passenger
compartment
blowerRUNNING
STOPPEDIn the event of a fault, refer to the
interpretation of status ET015.
ET030:Air conditioning
requestThis request is sent by the
UCH to the engine
management computer.
There are two possible
scenarios:
1
st scenario: vehicle equipped
with manual air conditioning.
The request is made by
pressing the air conditioning
button.
2
nd scenario: vehicle
equipped with climate control.
The request is made following
a user request or climate
control computer request.In the event of a fault, refer to the
interpretation of status ET030.
PR025:Engine speed0 rpmIn the event of a fault, run fault
finding on the multiplex network
(see 88B, Multiplex) then run
fault finding on the injection
system (see 13B, Diesel
injection or 17B, Petrol
injection).

87B-82
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: BATTERY
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Battery voltagePR001:Battery voltage9 V < X < 16 VIn the event of a fault, run fault
finding on the charging circuit
(see 80A, Battery).
PR074:Battery setpoint
voltageIndicates the battery
setpoint in V.In the event of a fault, apply the
interpretation of parameter
PR074.
PR076:Battery voltage after
restIndicates the battery
voltage after rest in V.In the event of a fault, apply the
interpretation of parameter
PR076.
Alternator
operationET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, apply the
interpretation of status ET142.

87B-83
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: ALTERNATOR
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Battery voltagePR073:Alternator charge
signalIndicates the
alternator charge in V.In the event of a fault, apply the
interpretation of parameter PR073.
Alternator
setpointPR075:Alternator setpoint
voltage
Indicates the alternator
setpoint in V.In the event of a fault, apply the
interpretation of parameter PR075.
Battery voltagePR001:Battery voltage9 V < X < 16 VIn the event of a fault, run fault finding
on the charging circuit (see, 80A
Battery), run fault finding on the
multiplex network (see 88B,
Multiplex) and run fault finding on the
injection (see 13B, Diesel injection
or 17B, Petrol injection).
EnginePR024:Engine coolant
temperature˚C
PR025:Engine speedrpmIn the event of a fault, run fault finding
on the multiplex network (see 88B,
Multiplex) and run fault finding on the
injection (see 13B, Diesel injection
or 17B, Petrol injection).
ET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, apply the
interpretation of status ET142.
AlternatorAC130:Alternator regulationIndicates the
regulation of the
alternator in volts.In the event of a fault, run fault finding
on the charging circuit (see 80A,
Battery).

87B-87
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET015
PASSENGER COMPARTMENT FAN
NOTESNo faults should be present or stored.
Apply this status for vehicles fitted with manual air conditioning or heating.
Apply the checks if there is an inconsistency between the value of the status
and the air actually blown.
SPECIFICATIONSRUNNING
STOPPED
Check the configuration of the heating and air conditioning type of the vehicle:
–Check that LC013 "Air conditioning type" is "Heating" or "Manual" or "Automatic" according to the
equipment level. Otherwise carry out CF019 Air conditioning type.
Check the presence and condition of fuses F28 (30 A), F29 (15 A), F42 (10 A) on the passenger compartment
fuse and relay box (component code 1016).
Replace the fuse(s) if necessary.
Check the condition and connection of the connectors for the air conditioning control panel and blower unit
(manual air conditioning) (tabs bent, oxidised, broken).
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET015