engine coolant RENAULT TWINGO 2009 2.G Engine And Peripherals Repair Manual

19A-52
COOLING
Engine cooling fan assembly: Removal - Refitting
C44, and K9K
19A
aPress on the engine cooling fan assembly locking
tabs (2) on the cooling radiator.
aWithdraw the engine cooling fan assembly from the
cooling radiator from above, while pressing on the
locking tabs.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aFit the engine cooling fan assembly to the cooling ra-
diator.
aClip the engine cooling fan assembly to the cooling
radiator.
aConnect the electrical connectors to the engine cool-
ing fan assembly.aClip:
-the engine cooling fan assembly wiring in place,
-the coolant hose at the bottom of the engine cool-
ing fan assembly.
II - FINAL OPERATION
aRefitting the front upper cross member (see MR 412
Bodywork, 42A, Upper front structure, Cross
member: Removal - Refitting).
aFit the « cable - bonnet catch » assembly.
aRefit the bonnet catch nuts.
aClip and move away from the front upper cross
member:
-the expansion bottle,
-the air filter inlet air pipe.
aRefit:
-the air filter inlet air pipe bolt onto the front upper
cross member,
-the expansion bottle bolt onto the front upper cross
member,
-the cooling radiator retaining lug bolt.
aTighten on the front upper cross member:
-the air filter inlet air pipe bolt onto the front upper
cross member,
-the expansion bottle bolt onto the front upper cross
member,
-the cooling radiator retaining lug bolt.
aRefit:
-the left-hand and right-hand headlights (see 80B,
Headlights, Halogen headlights: Removal - Re-
fitting),
-the front bumper ( (see Front bumper: Removal -
Refitting) ),
-the engine undertray,
-the engine undertray bolts.
aTighten the engine undertray bolts until contact is
made.
aConnect the battery ( (see Battery: Removal - Re-
fitting) ). STANDARD HEATING
120325
Note:
Be careful not to press too hard on the tabs to
avoid breaking them.
Note:
Check that the tabs lock the engine cooling fan
assembly on the cooling radiator correctly.

19A-58
COOLING
Coolant pump inlet pipe: Removal - Refitting
K9K
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see ) (MR 411, 80A, Bat-
tery).
aRemove:
-the engine cover,
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (MR 411, 85A, Wip-
ers - Washers),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior
equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (MR 412, 56A, Exterior equipment),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the headlights (see Halogen headlight: Removal
- Refitting) (MR 411, 80B, Headlights),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (MR 412,
42A, Upper front structure).
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
aRemove the engine tie-bar (see 19D, Engine
mounting, Lower engine tie-bar: Removal - Refit-
ting, page 19D-18) . Special tooling required
Mot. 1672Low er engine support.
Mot. 1448Remote operation pliers for
hose clips .
Tightening torquesm
subfame front bolt62 Nm
subframe rear bolt105 Nm
IMPORTANT
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any
repair (see ) .
IMPORTANT
When working in the engine compartment, take
care as the radiator fan(s) may start up unexpect-
edly (risk of being cut).
To avoid any risk of serious burns when the engine
is hot:
-do not open the expansion bottle cap,
-do not drain the cooling system,
-do not open the bleed screw(s).
WARNING
Before the operation, protect the electrical accesso-
ries to prevent any risk of shor t circuiting and pro-
tect the belts to avoid damaging them.
WARNING
When carr ying out a repair that requires a complete
change, it is essential to flush the circuit with clean
water, blast compressed air through the circuit to
drive out the water, fill and bleed the circuit and
then measure the effective protection.
The cr iteria to be met are:
-protection down to -25˚C ±± ± ±
2 for cold and temper-
ate countries,
-protection down to -40˚C ±± ± ±
2 for "extreme cold"
countries.
WARNING
The coolant helps to keep the engine running prop-
erly (heat exchange).
The system must not operate using pure water.

19A-59
COOLING
Coolant pump inlet pipe: Removal - Refitting
K9K
19A
aRemove:
-the front bolt (1) from the subframe,
-the rear bolt (2) from the subframe.
aPosition the (Mot. 1672).
aRemove:
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the multifunction support (see 10A, Engine and
cylinder block assembly, Multifunction sup-
port: Removal - Refitting, page 10A-63) ,
-the oil cooler (see 10A, Engine and cylinder
block assembly, Oil-coolant heat exchanger:
Removal - Refitting, page 10A-33) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the bolt (3) from the coolant pump inlet pipe,
-the coolant pump inlet pipe,
-the coolant pump inlet pipe seal.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the new water pump inlet pipe seal,
-the coolant pump inlet pipe,
-the coolant pump inlet pipe bolt.
aConnect the cooling hose using the tool (Mot. 1448).
II - FINAL OPERATION.
aRefit:
-the coolant-oil heat exchanger (see 10A, Engine
and cylinder block assembly, Oil-coolant heat
exchanger: Removal - Refitting, page 10A-33) ,
-the multifunction support (see 10A, Engine and
cylinder block assembly, Multifunction sup-
port: Removal - Refitting, page 10A-63) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
120040
121417

19A-60
COOLING
Coolant pump inlet pipe: Removal - Refitting
K9K
19A
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) .
aRemove the (Mot. 1672).
aRefit:
-the new subframe front bolt,
-the new subframe rear bolt.
aTorque tighten:
-the subfame front bolt (62 Nm),
-the subframe rear bolt (105 Nm).
aRefit the engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) .
aFill the cooling system (see 19A, Cooling, Cooling
system: Draining - Refilling, page 19A-9) .
aRefit:
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (MR 412,
42A, Upper front structure),
-the headlights (see Halogen headlight: Removal
- Refitting) (MR 411, 80B, Headlights),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (MR 412, 56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior
equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (MR 411, 85A, Wip-
ers - Washers),
-the engine cover.
aConnect the battery (see ) (MR 411, 80A, Battery).

19A-61
COOLING
Coolant pump inlet pipe: Removal - Refitting
D4F, and 780 or 782
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see ) (80A, Battery).
aRemove the engine undertray.
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aSeparate the clips on the coolant pump inlet pipe
hoses using the tool (Mot. 1448).
aDisconnect the coolant pump inlet pipe hoses.
aRemove:
-the bolts (1) from the coolant pump inlet pipe,
-the coolant pump inlet pipe,-the coolant pump inlet pipe seal.
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: seal between cool-
ant pump inlet pipe and coolant pump.
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consum-
ables - Products) to clean the bearing surfaces of
the coolant pump inlet pipe.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-a new seal on the coolant pump inlet pipe,
-the coolant pump inlet pipe,
-the coolant pump inlet pipe bolts.
aTorque tighten the coolant pump inlet pipe bolts
(10 N.m).
aConnect the hoses to the coolant pump inlet pipe.
aRefit the clips on the coolant pump inlet pipe hoses
using the tool (Mot. 1448).
III - FINAL OPERATION
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .
aRefit the engine undertray.
aConnect the battery (see ) (80A, Battery). Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
Tightening torquesm
coolant pump inlet pipe
bolts10 N.m
120956

19A-62
COOLING
Coolant pump inlet pipe: Removal - Refitting
K4M
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see ) (80A, Battery).
aRemove the engine undertray.
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
aRemove:
-the dipstick,
-the bolts (1) from the dipstick guide,
-the dipstick guide.aDisconnect:
-the pinking sensor connector (2) ,
-the oil pressure sensor connector (3) . Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
Tightening torquesm
coolant pump inlet pipe
bolts25 N.m
132368
132374

19A-63
COOLING
Coolant pump inlet pipe: Removal - Refitting
K4M
19A
II - REMOVAL OPERATION
aRemove the clip (4) from each cooling hose using
the tool (Mot. 1448).
aDisconnect the cooling hoses from the coolant pump
inlet pipe.
aRemove:
-the bolts (5) from the coolant pump inlet pipe,
-the coolant pump inlet pipe.
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: seal between cool-
ant pump inlet pipe and coolant pump.
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to clean and degrease:
-the seal housing in the cylinder block,
-the coolant pump inlet pipe seal housing if it is be-
ing reused.
II - REFITTING OPERATION
aRefit the coolant pump inlet pipe fitted with a new
seal.aTorque tighten in order the coolant pump inlet pipe
bolts (25 N.m).
aConnect the cooling hoses to the coolant pump inlet
pipe.
aFit each cooling hose clip using the tool (Mot. 1448).
III - FINAL OPERATION
aConnect:
-the oil pressure sensor connector,
-the pinking sensor connector.
aRefit:
-dipstick guide ,
-the dipstick.
aConnect the battery (see ) (80A, Battery).
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .
aRefit the engine undertray.
131781
131781

19A-65
COOLING
Expansion bottle: Removal - Refitting
D4F or D7F or K4M or K9K
19A
aRemove the tool (Ms. 583) from the expansion bottle
hoses.
aRefit the expansion bottle.
II - FINAL OPERATION
aTop up the coolant level in the expansion bottle.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
aRefit the engine cover.
aRefit the oil filler neck. K9K
D4F

19A-67
COOLING
Coolant temperature sensor: Removal - Refitting
K9K
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove the front engine cover.
aUnclip the neck on the gearbox.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the coolant temperature sensor connec-
tor.
aRemove:
-the coolant temperature sensor clip,
-the coolant temperature sensor,
-the coolant temperature sensor seal.
REFITTING
I - REFITTING PREPARATIONS OPERATION
a
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the new seal on the coolant temperature sensor,
-the coolant temperature sensor,
-the coolant temperature sensor clip.
aConnect the coolant temperature sensor connector.
III - FINAL OPERATION.
aClip the channel to the gearbox.
aFill the cooling system (see 19A, Cooling, Cooling
system: Draining - Refilling, page 19A-9) .
aRefit the engine cover. IMPORTANT
When working in the engine compartment, take
care as the radiator fan(s) may start up unexpect-
edly (risk of being cut).
To avoid any risk of serious burns when the engine
is hot:
-do not open the expansion bottle cap,
-do not drain the cooling system,
-do not open the bleed screw(s).
WARNING
Before the operation, protect the electrical accesso-
ries to prevent any risk of shor t circuiting and pro-
tect the belts to avoid damaging them.
WARNING
The coolant helps to keep the engine running prop-
erly (heat exchange).
The system does not operate using pure water.
WARNING
The seals m ust always be replaced.

19A-71
COOLING
Coolant temperature sensor: Removal - Refitting
K4M
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the air filter unit (see 12A, Fuel mixture,
Air filter unit: Removal - Refitting, page 12A-13) .II - REMOVAL OPERATION
aDisconnect the coolant temperature sensor connec-
tor (1) .
aRemove:
-the coolant temperature sensor clip (2) ,
-the coolant temperature sensor,
-the coolant temperature sensor seal.
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: coolant tempera-
ture sensor seal.
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to clean and degrease:
-the seal housing in the water chamber,
-the seal mating face of the coolant temperature
sensor if reused.
II - REFITTING OPERATION
aRefit:
-the coolant temperature sensor fitted with a new
seal,
-the coolant temperature sensor clip.
aConnect the coolant temperature sensor connector. IMPORTANT
The circuits are designed to be pressurised, so be
careful at high temperatures (risk of serious burns).
Do not remove the cap from the expansion bottle
while the engine is hot.
Take care when carrying out a repair under the bon-
net, as the radiator fan(s) may start to operate with-
out warning.
Do not open the bleed screw(s) with the engine run-
ning.
WARNING
Before the operation, protect the electrical accesso-
ries to prevent any risk of shor t circuiting and pro-
tect the belts to avoid damaging them.
WARNING
The coolant helps to keep the engine running prop-
erly (heat exchange).
The system does not operate using pure water.
131762