dashboard RENAULT TWINGO 2009 2.G Mechanism And Accessories Workshop Manual

Contents
55A EXTERIOR PROTECTION
Front bumper: Removal -
Refitting 55A-1
Front bumper: Stripping -
Rebuilding 55A-3
Rear bumper : Removal -
Refitting 55A-10
Rear bumper : Stripping -
Rebuilding 55A-13
Rear bumper : Conversion 55A-14
Front side door protective
strip: Removal - Refitting 55A-15
Rear wing protective strip:
Removal - Refitting 55A-16
Roof protection strip:
Removal - Refitting 55A-17
Front wheel arch liner:
Removal - Refitting 55A-18
56A EXTERIOR EQUIPMENT
Scuttle panel gr ille: Removal
- Refitting 56A-1
Tailgate spoiler: Removal -
Refitting 56A-3
Scoop under the scuttle
panel grille: Removal -
Refitting 56A-6
Door mirror: Removal -
Refitting 56A-8
Door mirror casing: Removal
- Refitting 56A-9
Door mirror glass: Removal -
Refitting 56A-10
Side decorative strips:
Removal - Refitting 56A-11
Sill panel extension:
Removal - Refitting 56A-13
Rear wing extension:
Removal - Refitting 56A-1557A INTERIOR EQUIPMENT
Dashboard: Removal -
Refitting 57A-1
Dashboard: Conversion 57A-4
Dashboard side air vent:
Removal - Refitting 57A-6
Centre front panel: Removal
- Refitting 57A-7
Glovebox: Removal -
Refitting 57A-9
Dashboard storage
compar tment: Removal -
Refitting 57A-11
Centre console: Removal -
Refitting 57A-12
Interior rear-view mirror:
Removal - Refitting 57A-14
Sun visor: Removal -
Refitting 57A-16
59A SAFETY ACCESSORIES
Front seat belt: Removal -
Refitting 59A-1
Rear seat belt: Removal -
Refitting 59A-3
Rear seat belt buckle:
Removal - Refitting 59A-5

54A-1
WINDOWS
Windscreen: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the windscreen wiper arms (see Winds-
creen wiper arm: Removal - Refitting) (MR 411,
85A, Washing - Wiping).
aRemove the lower trim pieces (1) from the winds-
creen.
aRemove:
-the scuttle panel grille (see 56A, Exterior equip-
ment, Scuttle panel grille: Removal - Refitting,
page 56A-1) ,
-the interior rear-view mirror (see 57A, Interior
equipment, Interior rear-view mirror: Removal -
Refitting, page 57A-14) ,
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim).
aDisconnect the rain and light sensor (depending on
the equipment level).II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the seal (2) from the windscreen.
aProtect the windscreen surround using masking ta-
pe.
aPosition the dashboard protector (Car. 1818).
a
aCut the cement bead. Special tooling required
Car. 1818Instr ument panel protector
Note:
Leave the rain sensor in place on the old winds-
creen during the replacement operation (depen-
ding on the equipment level).
119268
119271
108156
Note:
When cutting the cement bead, take care not to
cut the wiring harness.

57A-1
INTERIOR EQUIPMENT
Dashboard: Removal - Refitting
57A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove the passenger front airbag (see Passen-
ger's frontal airbag: Removal - Refitting) (88C,
Airbags and pretensioners).
aRemove:
-the windscreen pillar trims (see Windscreen pillar
trim: Removal - Refitting) (71A, Body internal
trim),
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and pre-
tensioners),
-the steering wheel (see Steering wheel: Removal
- Refitting) (36B, Power-assisted steering).aRemove the rev counter (depending on the equip-
ment level) (see Rev counter: Removal - Refitting)
(83A, Instrument panel).
aRemove:
-the steering column switch assembly (see Stee-
ring column switch assembly: Removal - Refit-
ting) (84A, Control - Signals),
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),
-the tweeters (see Tweeter: Removal - Refitting)
(86A, Radio),
-the centre console (see 57A, Interior equipment,
Centre console: Removal - Refitting, page 57A-
12) ,
-the centre front panel (see 57A, Interior equip-
ment, Centre front panel: Removal - Refitting,
page 57A-7) ,
-the control panel (see Control panel: Removal -
Refitting) (61A, Heating).
aUnclip the dashboard side faces. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
FRONT SIDE AIRBAG
ENGINE REV COUNTER
121136

57A-2
INTERIOR EQUIPMENT
Dashboard: Removal - Refitting
57A
aDisconnect the passenger airbag deactivation con-
nector.
aUnclip:
-the access flap (1) ,
-the diagnostic socket (2) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the dashboard bolts (3) .
121135
119521
131791
121159

57A-3
INTERIOR EQUIPMENT
Dashboard: Removal - Refitting
57A
aPartially remove the dashboard (this operation re-
quires two people).
aDetach the various wiring from the dashboard.
aRemove the dashboard (this operation requires two
people).
aNote the route of the cabling.
REFITTING
I - REFITTING PREPARATION OPERATION
aEnsure that the wiring is in good condition.
II - REFITTING OPERATION FOR PART
CONCERNED
aPartially refit the dashboard (this operation requires
two people).
aRefit:
-the various cable harnesses,
-the dashboard (this operation requires two people).
III - FINAL OPERATION.
aClip:
-the diagnostic socket (2) ,
-the access flap (1) .
aConnect the passenger airbag deactivation connec-
tor.
aClip on the dashboard side faces.
aRefit:
-the control panel (see Control panel: Removal -
Refitting) (61A, Heating),
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),-the tweeters (see Tweeter: Removal - Refitting)
(86A, Radio),
-the centre front panel (see 57A, Interior equip-
ment, Centre front panel: Removal - Refitting,
page 57A-7) ,
-the centre console (see 57A, Interior equipment,
Centre console: Removal - Refitting, page 57A-
12) ,
-the steering column switch assembly (see Stee-
ring column switch assembly: Removal - Refit-
ting) (84A, Control - Signals).
aRefit the rev counter (see Rev counter: Removal -
Refitting) (83A, Instrument panel).
aRefit:
-the steering wheel (see Steering wheel: Removal
- Refitting) (36B, Power-assisted steering),
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and pre-
tensioners),
-the windscreen pillar trims (see Windscreen pillar
trim: Removal - Refitting) (71A, Body internal
trim).
aRefit the passenger front airbag (see Passenger's
frontal airbag: Removal - Refitting) (88C, Airbags
and pretensioners).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aCarry out a function test on all functions.
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (88C, Airbags and pretensioners).
121157ENGINE REV COUNTER
FRONT SIDE AIRBAG
IMPORTANT
To avoid a fault with or even triggering of pyro-
technic components (airbags or pretensioners),
check the airbag computer using the diagnostic
tool.

57A-4
INTERIOR EQUIPMENT
Dashboard: Conversion
57A
I - DASHBOARD CONVERSION REQUIRED FOR
FITTING AN OFFSET AUDIO SOCKET
1 - Offset audio socket holes
a (X1) = 22 mm.
(X2) = 16 mm.
(X3) = 23 mm.
aDrill the holes using a drill bit (∅ 9 mm).2 - Mounting holes for the offset audio socket unit
a (X4) = 8 mm.
(X5) = 7 mm.
(X6) = 27 mm.
aDrill the holes using a drill bit (∅ 7.5 mm).
II - DASHBOARD CONVERSION REQUIRED FOR
FITTING THE AUDIO CONNECTING BOX (ACB)
1 - Unit wiring hole (ACB)
aHole (7) =∅ 20 mm.
aEnlarge the hole (7) using a conical cutter.
121381
121381
127770

57A-5
INTERIOR EQUIPMENT
Dashboard: Conversion
57A
2 - Unit mounting holes (ACB)
aPosition the unit (ACB) in the glovebox against the
upper edge (8) .
a (X9) = 15 mm
aMark the unit mounting holes.
aDrill the holes using a drill bit (∅ 3 mm).
127771
Note:
Connect the connector before fitting the unit
(ACB).

57A-6
INTERIOR EQUIPMENT
Dashboard side air vent: Removal - Refitting
57A
REFITTING
OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the dashboard side air vent at (1) .
REMOVAL
REFITTING OPERATION FOR PART CONCERNED
aClip on the dashboard side air vent back at (1) .
121711

57A-7
INTERIOR EQUIPMENT
Centre front panel: Removal - Refitting
57A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the radio (see Radio: Removal - Refitting) (MR
411, 86A, Radio),
-the centre console (see 57A, Interior equipment,
Centre console: Removal - Refitting, page 57A-
12) .
aRemove the dashboard lower trim.
aDisconnect the various connectors (1) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the upper section of the centre front panel at
(2) .
aRemove the upper section of the centre front panel.
aRemove:
-the bolts (3) ,
-the clips (4) ,
-the centre front panel.
121142
119711
121141
121161

57A-8
INTERIOR EQUIPMENT
Centre front panel: Removal - Refitting
57A
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the centre front panel,
-the bolts (3) ,
-the clips (4) ,
-the upper section of the centre front panel.
II - FINAL OPERATION.
aConnect the various connectors (1) .
aRefit:
-the dashboard lower trim,
-the centre console (see 57A, Interior equipment,
Centre console: Removal - Refitting, page 57A-
12) ,
-the radio (see Radio: Removal - Refitting) (MR
411, 86A, Radio).