wheel RENAULT TWINGO 2009 2.G Transmission Repair Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO, Model: RENAULT TWINGO 2009 2.GPages: 135
Page 124 of 135
29A-16
DRIVESHAFTS
Front driveshaft gaiter, wheel side: Removal - Refitting
JB1 or JH1 or JH3 or JR5
29A
II - REFITTING OPERATION FOR PART
CONCERNED
aFit the small securing clip (6) onto the driveshaft.
aLightly lubricate the driveshaft using the grease sup-
plied with the gaiter to facilitate its fitting.
aRefit the gaiter (7) onto the driveshaft.
aInsert the gaiter lip into the groove of the driveshaft.
aRefit the locking spring ring (8) .
aSpread the quantity of grease around the gaiter and
the stub axle bowl.aRefit the stub axle bowl (9) to the driveshaft by tap-
ping on the stub axle bowl using a brass drift until the
locking spring ring clicks into place behind the hub
bearing.
aFit the lip of the driveshaft gaiter into the groove on
the stub axle bowl.
aFit the small securing clip on the driveshaft gaiter.
aRefit the big securing clip on the driveshaft gaiter.
128412
128416
109768
Note:
Chec k that the gaiter lip is correctly positioned in
the g roove of the driveshaft.
Page 125 of 135
29A-17
DRIVESHAFTS
Front driveshaft gaiter, wheel side: Removal - Refitting
JB1 or JH1 or JH3 or JR5
29A
Clic clip
Clip with profile end
aTighten the clips using the tool (Tav. 1168) (10) for
clic clips or the tool (Tav. 1784) (11) for profile end
clips.
III - FINAL OPERATION
aRefit:
-the driveshaft on the side concerned (see 29A,
Driveshafts, Front right-hand driveshaft: Re-
moval - Refitting, page 29A-8) or (see 29A,
Driveshafts, Front left-hand driveshaft: Remov-
al - Refitting, page 29A-2) ,-the wheel on the side concerned (see Wheel: Re-
moval - Refitting) (35A, Wheels and tyres),
-the engine undertray.
115197
115196
Page 126 of 135
29A-18
DRIVESHAFTS
Front right-hand driveshaft gaiter, gearbox side: Removal - Refitting
JB1 or JH1 or JH3 or JR5
29A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the engine undertray,
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand driveshaft (see 29A, Drive-
shafts, Front right-hand driveshaft: Removal -
Refitting, page 29A-8) . Special tooling required
Tav. 1168"Clic" type clip pliers for drive-
shafts with a thermoplastic
gaiter.
Tav. 1784Pliers for the driveshaft gaiter
collar.
Equipment required
par ts washer
108557
2943
(1) Big securing clip
(2) Small secur ing clip
(3) Driveshaft gaiter
(4) Yoke sleeve
(5) Spider
(6) Cup
(7) Cup spring
(8) Driveshaft
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
Page 130 of 135
29A-22
DRIVESHAFTS
Front right-hand driveshaft gaiter, gearbox side: Removal - Refitting
JB1 or JH1 or JH3 or JR5
29A
Clic clip
Clip with profile end
aTighten the clips using the tool (Tav. 1168) (10) for
clic type clips or the tool (Tav. 1784) (11) for profile
end clips.
III - FINAL OPERATION
aRefit:
-the front right-hand driveshaft (see 29A, Drive-
shafts, Front right-hand driveshaft: Removal -
Refitting, page 29A-8) ,-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the engine undertray.
115197
115196