door lock RENAULT TWINGO 2009 2.G Trim And Upholstery Workshop Manual

71A-1
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) .
aRemove:
-the front seats completely (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-8) ,
-the rear seats completely (depending on equip-
ment level) (see 76A, Rear seat frames and me-
chanisms, Complete rear seat: Removal -
Refitting, page 76A-1) ,
-the rear bench seat base (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seat base: Removal - Refit-
ting, page 76A-6) ,
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) ,
-the centre front panel (see Centre front panel: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment),-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) ,
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the front door sill lining (see 71A, Body internal
trim, Front door sill lining: Removal - Refitting,
page 71A-7) .
aRemove:
-the bolt (1) ,
-the storage compartment under the front seat. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121608

71A-2
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting
71A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the centring pin (2) from the centre console,
-the clip (3) ,
-the floor carpet.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aFit the seat wiring.
aRefit:
-the floor carpet,
-the clip (3) ,
-the centre console centring pin (2) .II - FINAL OPERATION.
aRefit:
-the storage compartment under the front seat,
-the bolt (1) ,
-the front door sill lining (see 71A, Body internal
trim, Front door sill lining: Removal - Refitting,
page 71A-7) ,
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) ,
-the centre front panel (see Centre front panel: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment),
-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) ,
-the rear bench seat base (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seat base: Removal - Refit-
ting, page 76A-6) ,
-the rear seats completely (depending on equip-
ment level) (see 76A, Rear seat frames and me-
chanisms, Complete rear seat: Removal -
Refitting, page 76A-1) ,
-the front seats completely (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) .
aUnlock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
121162

71A-4
BODY INTERNAL TRIM
Headlining: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aPartially remove the front side door and tailgate
seals.aUnclip the trim piece (1) from the sun visor shutter
cross member mounting.
aRemove:
-the finishing seal (2) from the sunroof
-the sunroof switch plate (see Sunroof switch: Re-
moval - Refitting) (MR 411, 87D, Electric window
winders - Sunroof).
aRemove:
-the interior lights (see Interior light: Removal -
Refitting) (MR 411, 81B, Interior lights),
-the sun visors (see Sun visor: Removal - Refit-
ting) (MR 412, 57A, Interior equipment),
-the windscreen pillar trims (see 71A, Body inter-
nal trim, Windscreen pillar trim: Removal - Re-
fitting, page 71A-9) ,
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) (MR 412, 76A, Rear seat frame
and runners),
-the rear parcel shelf side trim panels (see 71A,
Body internal trim, Rear parcel shelf side trim:
Removal - Refitting, page 71A-15) ,
-the rear panel trims (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) , Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
OPENING ROOF
121712

71A-6
BODY INTERNAL TRIM
Headlining: Removal - Refitting
71A
aRefit the headlining (this operation requires two peo-
ple).
aRefit clips (4) .
III - FINAL OPERATION.
aRefit the interior light and sunroof wiring harnesses
(depending on equipment level).
aConnect the interior light and sunroof connectors (3)
(depending on equipment level).
aRefit:
-the interior lights (see Interior light: Removal -
Refitting) (MR 411, 81B, Interior lights),
-the sun visors (see Sun visor: Removal - Refit-
ting) (MR 412, 57A, Interior equipment),
-the windscreen pillar trims (see 71A, Body inter-
nal trim, Windscreen pillar trim: Removal - Re-
fitting, page 71A-9) ,
-the rear quarter panel trims (see 71A, Body inter-
nal trim, Quarter panel trim: Removal - Refit-
ting, page 71A-12) .
-the B-pillar upper trims (see 71A, Body internal
trim, B-pillar upper trim: Removal - Refitting,
page 71A-10) ,
-the rear panel trims (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the rear parcel shelf side trim panels (see 71A,
Body internal trim, Rear parcel shelf side trim:
Removal - Refitting, page 71A-15) ,
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) (MR 412, 76A, Rear seat frame
and runners),aRefit:
-the sunroof switch plate (see Sunroof switch: Re-
moval - Refitting) (MR 411, 87D, Electric window
winders - Sunroof),
-the sunroof finishing seal (2) .
aFit the sun visor headlining cross member mounting
trim piece (1) .
aRefit the front side door and tailgate seals.
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners). OPENING ROOF
OPENING ROOF