warning RENAULT TWINGO 2012 2.G Owner's Guide

speed limiter ......................................... (up to the end of the DU)
cruise control-speed limiter................... (up to the end of the DU)
cruise control ........................................ (up to the end of the DU)
driving ................................................... (up to the end of the DU)
2.15
ENG_UD24753_4
régulateur limiteur fonction limiteur (X44 - Renault)
ENG_NU_952-4_X44_Renault_2
Cruise control, Speed limiter: speed limiter
cRUISe coNtRol - SPeeD lIMIteR: limiter function (1/3)
The speed limiter function helps you
stay within the driving speed limit that
you choose, known as the limit speed.controls
1 Main “On/Off” switch.
2 Limit speed activation, storage and
increase switch (+).
3 Limit speed activation, storage and
decrease switch (-).
4 Switch the function to standby, with
limit speed stored (O).
5 Stored limit speed activation, stor -
age and recall (R).
Switching on
Press switch 1 on the side showing .
Warning light 6 comes on and dashes
appear on the instrument panel to in -
dicate that the speed limiter function
is operating and waiting to store a limit
speed.
To store the current speed, press
switch 2 (+) or 3 (-): the limit speed
will replace the dashes. The minimum
stored speed is 20 mph (30 km/h).
The stored speed information appears
on instrument panel display .
6
1
3452

JauneNoirNoir texte
2.19
ENG_UD24754_4
Régulateur-limiteur de vitesses : fonction régulateur (X44 - Renault)
ENG_NU_952-4_X44_Renault_2
cRUISe coNtRol - SPeeD lIMIteR: cruise control function (2/4)
Switching on
Press switch 1 on the side showing .
Warning light 6 comes on and dashes
appear on the instrument panel to indi -
cate that the cruise control function is
operating and waiting to store a cruis -
ing speed.
Activating cruise control
At a steady speed (above 20 mph
30 km/h) press switch 2 (+) or 3 (-): the
function is activated, the current speed
is stored and replaces the dashes on
the instrument panel.
Cruise control activation is confirmed
when the box around indicator light 6 is
illuminated.
Driving
Once a cruising speed is stored and
the cruise control function is active,
you may lift your foot off the accelera -
tor pedal.
Important: you are never -
theless advised to keep
your feet close to the pedals
in order to react if neces -
sary.
6
1
2345

automatic gearbox (use) ........................................ (current page)
JauneNoirNoir texte
2.23
ENG_UD24716_6
Boîte de vitesses Quickshift (X44 - Renault)
ENG_NU_952-4_X44_Renault_2
Starting
The display shows N (neutral) and A
(automatic mode).
Forwards gear
– With the brake pedal depressed,
push the selector lever forwards and
release it (the number 1 will appear
on the display);
– release the brake pedal and acceler-
ate gently to move forwards.
Reverse
– With your foot on the brake pedal,
push the selector lever towards the
right and backwards, and then re -
lease it.
Reverse gear is engaged (letter R
appears on the display).
– release the brake pedal then accel -
erate gently to move backwards. The
engine’s idle speed is sufficient for
parking manoeuvres.
When the vehicle is stationary, push
the selector lever towards the front to
engage a forwards gear.
operation
Switch on the ignition.
The display on the instrument panel
switches on. If neutral (N) is displayed,
start the engine but do not depress the
accelerator.
If a gear other than neutral ( N) is dis -
played, it will flash; starting is possi-
ble if you depress the brake pedal
(indicator light 4 will come on if you
forget) when holding the key in the
starting position.
The gear will automatically change to
neutral (N) and the engine will start.
You may also select neutral after
switching on the ignition by pushing the
lever to the right whilst depressing the
brake pedal.
When the engine is running, automatic
mode will be selected by default.
Note: if the display does not light up
when the ignition is switched on (dis -
charged battery), do not attempt to start
the engine by pushing the vehicle. Shifting to neutral
With the brake pedal depressed, push
the lever to the right.
Note:
when the vehicle is stationary,
you must depress the brake pedal to
engage or disengage a gear. Otherwise,
warning light 4 will light up.
QUIcKShIFt GeARBoX (2/5)
4
The oil level in the automatic gearbox system reservoir is variable depending on use. Adding oil is strictly forbidden
(except by qualified approved network personnel).

horn ....................................................................... (current page)
2.24
ENG_UD24716_6
Boîte de vitesses Quickshift (X44 - Renault)
ENG_NU_952-4_X44_Renault_2
Jaune NoirNoir texte
changing mode
You can change mode at any time
by pushing the lever to the left. This
switches mode without changing gear.
Driving in manual mode
Using the selector lever
Pushing the lever repeatedly allows
you to change gears manually:
– To change up a gear: push the lever
forwards;
– to change down a gear: push the
lever backwards;
– to change to neutral: with the brake
pedal depressed (indicator light 4
will come on if you forget), push the
lever towards the right.
Note: when the vehicle is stationary
(braking, red light, etc.), the system au-
tomatically switches to first gear.
By pushing the lever forwards twice
you can move up two gears at a time
(unless this causes low engine speeds).
By pushing the lever backwards twice
you can move down two gears at a time
(unless this causes overrevving).
Note: neutral may only be selected
when the vehicle is being driven or is
stationary when the brake pedal is
depressed (if you forget, warning
light 4 will light up).
Accelerating and overtaking
To obtain maximum vehicle perform -
ance, in automatic or manual mode,
quickly depress the accelerator pedal
beyond the kickdown point.
This will activate the kickdown func -
tion allowing you to change down to the
most suitable gear.
QUIcKShIFt GeARBoX (3/5)
Driving in automatic mode
Each time the ignition is switched on,
automatic mode is selected by default
(letter A on the display).
The vehicle is controlled using the ac -
celerator and the brake.
Gears will change automatically at
the correct moment and at a suitable
engine speed because automatic mode
takes into consideration the road sur -
face and the chosen driving style.
You may change the gear selection
made by the automatic system (unless
this risks the engine being overrevved
or underrevved):
– by pushing the lever forwards or
backwards.
You can stop the vehicle at red lights,
with the gear engaged, by pressing the
brake pedal; there is no need to change
to neutral.
If the engine is being overrevved or underevved, the system will select the opti-
mal gear.

JauneNoirNoir texte
2.25
ENG_UD24716_6
Boîte de vitesses Quickshift (X44 - Renault)
ENG_NU_952-4_X44_Renault_2
QUIcKShIFt GeARBoX (4/5)
Parking
To park the vehicle with a gear en -
gaged (on a slope, for example): before
switching off the engine, check that a
gear other than N is displayed on the
instrument panel.
The next time the engine is started, de-
press the brake pedal. The vehicle will
then automatically change to neutral
(letter N on the display).
Audible warning
If you hold the vehicle on a slope for
too long without applying the brakes or
handbrake you will strain the system
and there is a risk that the clutch will
overheat.
In this case, an intermittent beeping
sound will remind you that you should
put your foot on the brake pedal or
apply the handbrake.
Never leave the vehicle with the engine
running when in gear. For safety rea -
sons you will hear an intermittent beep -
ing sound when you open the door if
you have not shifted into neutral or you
have not switched off the ignition or de-
pressed the brake pedal.
An impact to the underside of the vehicle (e.g.: striking a post, raised kerb
or other street furniture) may result in damage to the vehicle (e.g.: defor-
mation of an axle).
To avoid any risk of accident, have your vehicle checked by an approved
Dealer.

2.26
ENG_UD24716_6
Boîte de vitesses Quickshift (X44 - Renault)
ENG_NU_952-4_X44_Renault_2
QUIcKShIFt GeARBoX (5/5)
t owing the vehicle
If the gearbox is stuck in a gear:
– Switch on the ignition;
– select neutral with the brake pedal
depressed;
– check that the gearbox is in neutral
(by pushing the vehicle, for exam -
ple).
If you cannot find neutral you must tow
the vehicle with the front wheels raised.
the vehicle should always be towed
with the ignition switched off.operating faults
ÒWhen driving, if this warning
light comes on together with
warning light
©, this indicates a
system fault. In most cases, you may
still drive the vehicle, although it will not
function perfectly. Contact an approved
dealer as soon as possible.
the vehicle will not start
If you cannot start the engine and if the
battery is not discharged (display lit up):
– Switch on the ignition;
– select neutral;
– push the vehicle or roll it down a suf-
ficiently steep slope. Then push the
selector lever forwards.
The optimum gear for starting the
engine will then be automatically se -
lected.
Note: never attempt this manoeuvre in
reverse.

heating system ..................................... (up to the end of the DU)
air conditioning ..................................... (up to the end of the DU)
ventilation ............................................. (up to the end of the DU)
controls .................................................................. (current page)
air conditioning ..................................... (up to the end of the DU)
temperature regulation ......................... (up to the end of the DU)
heating and air conditioning system ..... (up to the end of the DU)
3.9
ENG_UD24164_1
Air conditionné automatique (X44 - Renault)
ENG_NU_952-4_X44_Renault_3
Automatic climate control
AuT oMATIC ClIMATE CoNTRol (1/9)
The controls
1 Clear View button to demist and
de-ice the windows.
2 Clear View function indicator light.
3 Air conditioning on and off.
4 and 7 Adjusting the air temperature.
5 Display.
6 Automatic mode on and off.
8 and 10 Passenger compartment air
distribution adjustment.
9 and 11 A d j u s t i n g t h e v e n t i l a t i o n
speed.
12 Heated rear screen with demisting
function and heated door mirrors
(depending on vehicle).
13 Heated rear screen warning light.
14 Air recirculation control.
Information and advice on use: refer
to the end of the paragraph on “Heating/
air conditioning”.
Buttons 1 and 12 are comple -
mented by operating indicator lights
(2 and 13):
– indicator light on, the function is
switched on;
– indicator light off, the function is
switched off.
12345678
9
10111213
14

3.14
ENG_UD24164_1
Air conditionné automatique (X44 - Renault)
ENG_NU_952-4_X44_Renault_3
Jaune NoirNoir texte
AuToMATIC ClIMATE CoNTRol (6/9)
Varying the ventilation speed
In automatic mode, the system uses
the most suitable amount of air to reach
and maintain the desired comfort level.
Automatic mode is switched off by
pressing buttons 9 and 11.
These buttons allow you to increase or
decrease ventilation speed.
Switching air conditioning on
or off
In automatic mode, the system switches
the air conditioning system on or off,
depending on the climate conditions.
Exit automatic mode by pressing
button 3 : the AUTO warning light on
display 5 goes out.
Button 3 activates (display warning
light comes on) or stops (warning light
goes out) the air conditioning function. Note:
the Clear View function auto -
matically activates the air condition -
ing system (indicator light on). Press
button 6 to return to automatic mode.
Do not open the refrigerant
fluid circuit. The fluid may
damage eyes or skin.
In automatic mode, in cold weather,
the ventilation will not start imme -
diately at maximum power but will
increase progressively until the
engine temperature is warm enough
to heat the passenger compartment
air. This may take from a few sec -
onds to several minutes.
356
9
11

windscreen de-icing/demisting .............................. (current page)
3.16
ENG_UD24164_1
Air conditionné automatique (X44 - Renault)
ENG_NU_952-4_X44_Renault_3
Jaune NoirNoir texte
AuToMATIC ClIMATE CoNTRol (8/9)
Clear View function
With the engine running , press
button 1 , and operating tell-tale 2
comes on.
The AUTO button indicator light (on the
display) goes out. This function rapidly demists/de-ices
the windscreen, the front side windows
and the door mirrors (depending on the
vehicle).
It automatically starts the air condition
-
ing, inhibits recirculation and switches
on the rear screen heating (warning
light 13).
Press button 12 if you do not want the
heated rear screen to be activated;
warning light 13 goes out.
Note: if you wish to reduce the air flow
(which may produce a certain amount
of noise in the passenger compart -
ment), press button 11.
To exit this function, press either:
– button 1 again;
– button 6 (the AUTO indicator light on
the display will light up).126
111213

battery................................................... (up to the end of the DU)
4.12
ENG_UD24730_3
Batterie (X44 - C44 - G44 - Renault)
ENG_NU_952-4_X44_Renault_4
Battery
Battery
Depending on the vehicle, this is lo -
cated underneath cover 1.
Battery access:
Depending on the vehicle, unclip
cover A.
Replacing the battery
As this operation is complex, we advise
you to contact an approved Dealer.
Take care when working in
the engine compartment
as the engine cooling fan
may start to operate at any
moment without warning.
Risk of injury.When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in the park position.
Risk of injury.
BATTER y
1
A
Label B
Observe the indications on the battery:
– 2 Naked flames and smoking are for-
bidden;
– 3 eye protection required;
– 4 keep children at a safe distance;
– 5 explosive materials;
– 6 refer to the handbook;
– 7 corrosive materials.
Handle the battery with care
as it contains sulphuric acid
which must not come into
contact with the eyes or
skin. If it does, wash the affected
area with plenty of cold water. If
necessary, consult a doctor.
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
B
234
567