lock RENAULT TWINGO RS 2009 2.G Air Conditioning Owner's Manual

61A-32
HEATING
Distribution unit: Removal - Refitting
AIR CONDITIONING
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDrain the coolant circuit using the refrigerant
charging station (see 62A, Air conditioning, Re-
frigerant circuit: Draining - Filling, page 62A-8) .
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment).a
aRemove:
-the bolt (1) from the expansion valve - compressor
connecting pipe.
-the bolt (2) from the condenser - expansion valve
connecting pipe.
aMove aside the connecting pipes.
aFit plugs to the openings. Special tooling required
Ms. 583Pipe clamps .
Mot. 1448Remote operation pliers for
hose clips .
Mot. 1202-01Clip pliers for hose clips
(large size).
Mot. 1202-02Clip pliers for hose clips
(small size)
Equipment required
refrigerant charging station
Diagnostic tool
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair (see 62A, Air conditioning, Air condition-
ing: Precautions for the repair, page 62A-1) .
119862
WARNING
To prevent moisture from entering the system,
place plugs on the cold loop components which
are open to the air.
WARNING
In order to avoid any refrigerant leaks, do not
damage (deform, twist, etc.) the pipe.
Note:
Use blanking plugs for the fuel circuits with part
numbers 77 01 208 229 or 77 01 476 857 to plug
any openings exposed to the open air. They must
be clean. Do not use any which have already
been used to plug a fuel circuit.

61A-36
HEATING
Distribution unit: Removal - Refitting
AIR CONDITIONING
61A
aRefit the storage compartment.
aRefit the radio (see Radio: Removal - Refitting)
(86A, Radio).
aRefit the tweeters (see Tweeter: Removal - Refit-
ting) (86A, Radio).
aRefit:
-the control panel (see 61A, Heating, Control pan-
el: Removal - Refitting, page 61A-65) ,
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),
-the passenger front airbag (see Passenger's fron-
tal airbag: Removal - Refitting) (88C, Airbags
and pretensioners),
-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (84A, Control - Signals),
-the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly),
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and seat
belt pretensioners).
aRefit the rev counter (see Rev counter: Removal -
Refitting) (83A, Instrument panel).
aConnect:
-the air filter unit air inlet pipe onto the air filter unit,
-the heater matrix inlet and outlet hoses.aFit the heater matrix inlet and outlet hose clips using
the (Mot. 1448) or (Mot. 1202-01) or (Mot. 1202-
02).
aRemove the (Ms. 583) on the heater matrix inlet and
outlet hoses.
aRefit the air outlet pipe onto the air filter unit.
aFit the air filter unit air inlet pipe.
aRemove the plugs from the openings.
aFit the connecting pipes.
aRefit:
-the bolt to the expansion valve - compressor con-
necting pipe,
-the bolt to the condenser - expansion valve con-
necting pipe.
aRefit:
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (88C, Airbags and pretensioners).
aFill up and bleed the cooling system (see Cooling
system: Draining - Refilling) (19A, Cooling).
aCheck the cooling circuit (see Engine cooling sys-
tem: Check) (19A, Cooling).
aConsult the refrigerant and oil quantity values before
filling the circuit (see 62A, Air conditioning, Air
conditioning: Parts and consumables for the re-
pair, page 62A-2) .
aFill the refrigerant circuit using the refrigerant
charging station (see 62A, Air conditioning, Re-
frigerant circuit: Draining - Filling, page 62A-8) .
aCheck that the air conditioning system is operating
correctly (see 62A, Air conditioning, Air condi-
tioning: Check, page 62A-4) . WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or RADIO
NO. 01 or RADIO NO. 03
ENGINE REV COUNTER
D7F

61A-38
HEATING
Distribution unit: Removal - Refitting
CLIMATE CONTROL
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDrain the coolant circuit using the refrigerant
charging station (see 62A, Air conditioning, Re-
frigerant circuit: Draining - Filling, page 62A-8) .
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment).a
aRemove:
-the bolt (1) from the expansion valve - compressor
connecting pipe.
-the bolt (2) from the condenser - expansion valve
connecting pipe.
aMove aside the connecting pipes.
aFit plugs to the openings. Special tooling required
Ms. 583Pipe clamps .
Mot. 1448Remote operation pliers for
hose clips .
Mot. 1202-01Clip pliers for hose clips
(large size).
Mot. 1202-02Clip pliers for hose clips
(small size)
Equipment required
refrigerant charging station
Diagnostic tool
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair (see 62A, Air conditioning, Air condition-
ing: Precautions for the repair, page 62A-1) .
119862
WARNING
To prevent moisture from entering the system,
place plugs on the cold loop components which
are open to the air.
WARNING
In order to avoid any refrigerant leaks, do not
damage (deform, twist, etc.) the pipe.
Note:
Use blanking plugs for the fuel circuits with part
no. 77 01 208 229 or 77 01 476 857 to plug any
openings exposed to the open air. They must be
clean. Do not use any which have already been
used to plug a fuel circuit.

61A-42
HEATING
Distribution unit: Removal - Refitting
CLIMATE CONTROL
61A
aRefit the storage compartment.
aRefit the radio (see Radio: Removal - Refitting)
(86A, Radio).
aRefit the tweeters (see Tweeter: Removal - Refit-
ting) (86A, Radio).
aRefit:
-the control panel (see 61A, Heating, Control pan-
el: Removal - Refitting, page 61A-65) ,
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),
-the passenger front airbag (see Passenger's fron-
tal airbag: Removal - Refitting) (88C, Airbags
and pretensioners),
-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (84A, Control - Signals),
-the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly),
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and seat
belt pretensioners).
aRefit the rev counter (see Rev counter: Removal -
Refitting) (83A, Instrument panel).
aConnect:
-the air filter unit air inlet pipe onto the air filter unit,
-the heater matrix inlet and outlet hoses.aFit the heater matrix inlet and outlet hose clips using
the (Mot. 1448) or (Mot. 1202-01) or (Mot. 1202-
02).
aRemove the (Ms. 583) on the heater matrix inlet and
outlet hoses.
aRefit the air outlet pipe onto the air filter unit.
aFit the air filter unit air inlet pipe.
aRemove the plugs from the openings.
aFit the connecting pipes.
aRefit:
-the bolt to the expansion valve - compressor con-
necting pipe,
-the bolt to the condenser - expansion valve con-
necting pipe.
aRefit:
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (88C, Airbags and pretensioners).
aFill up and bleed the cooling system (see Cooling
system: Draining - Refilling) (19A, Cooling).
aCheck the cooling circuit (see Engine cooling sys-
tem: Check) (19A, Cooling).
aConsult the refrigerant and oil quantity values before
filling the circuit (see 62A, Air conditioning, Air
conditioning: Parts and consumables for the re-
pair, page 62A-2) .
aFill the refrigerant circuit using the refrigerant
charging station (see 62A, Air conditioning, Re-
frigerant circuit: Draining - Filling, page 62A-8) .
aCheck that the air conditioning system is operating
correctly (see 62A, Air conditioning, Air condi-
tioning: Check, page 62A-4) . WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or RADIO
NO. 01 or RADIO NO. 03
ENGINE REV COUNTER
D7F

61A-44
HEATING
Heater matrix: Removal - Refitting
LEFT-HAND DRIVE
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment).aLoosen the clip (1) of the air outlet pipe on the air fil-
ter unit.
aRemove the air outlet pipe from the air filter unit (2) .
aDisconnect the air filter unit air inlet pipe (3) on the
air filter unit.
aMove aside the air inlet pipe from the air filter unit. Special tooling required
Ms. 583Pipe clamps .
Mot. 1448Remote operation pliers for
hose clips .
Mot. 1202-01Clip pliers for hose clips
(large size).
Mot. 1202-02Clip pliers for hose clips
(small size)
Equipment required
Diagnostic tool
Tightening torquesm
cross member reinforce-
ment bolts21 N.m
D7F
119715
119716

61A-48
HEATING
Heater matrix: Removal - Refitting
LEFT-HAND DRIVE
61A
aRefit:
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (88C, Airbags and pretensioners).
aFill up and bleed the cooling system (see Cooling
system: Draining - Refilling) (19A, Cooling).
aCheck the cooling circuit (see Engine cooling sys-
tem: Check) (19A, Cooling).

61A-49
HEATING
Heater matrix: Removal - Refitting
RIGHT-HAND DRIVE
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment).aLoosen the clip (1) of the air outlet pipe on the air fil-
ter unit.
aRemove the air outlet pipe from the air filter unit (2) .
aDisconnect the air filter unit air inlet pipe (3) on the
air filter unit.
aMove aside the air inlet pipe from the air filter unit. Special tooling required
Ms. 583Pipe clamps .
Mot. 1448Remote operation pliers for
hose clips .
Mot. 1202-01Clip pliers for hose clips
(large size).
Mot. 1202-02Clip pliers for hose clips
(small size)
Equipment required
Diagnostic tool
D7F
119715
119716

61A-52
HEATING
Heater matrix: Removal - Refitting
RIGHT-HAND DRIVE
61A
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),
-the passenger front airbag (see Passenger's fron-
tal airbag: Removal - Refitting) (88C, Airbags
and pretensioners),
-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (84A, Control - Signals),
-the steering wheel (see Centre console: Removal
- Refitting) (36A, Steering assembly),
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and seat
belt pretensioners).
aRefit the rev counter (see Rev counter: Removal -
Refitting) (83A, Instrument panel).
aRefit the air outlet pipe onto the air filter unit.
aFit the air filter unit air inlet pipe.
aConnect the air filter unit air inlet pipe on the air filter
unit.
aConnect the heater matrix inlet and outlet hoses.
aFit the heater matrix inlet and outlet hose clips using
the (Mot. 1448) or (Mot. 1202-01) or (Mot. 1202-
02).
aRemove the (Ms. 583) from the heater matrix inlet
and outlet hoses.
aRefit:
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (88C, Airbags and pretensioners).
aFill up and bleed the cooling system (see Cooling
system: Draining - Refilling) (19A, Cooling).
aCheck the cooling circuit (see Engine cooling sys-
tem: Check) (19A, Cooling).
ENGINE REV COUNTER
D7F

61A-53
HEATING
Fan assembly: Removal - Refitting
LEFT-HAND DRIVE
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413 Fault finding, 88C, Airbags and pretension-
ers).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the passenger's front airbag (see Passenger's
frontal airbag: Removal - Refitting) (MR 411,
88C, Airbags and pretensioners),
-the front right-hand side air distribution duct (see
61A, Heating, Front side air distribution duct:
Removal - Refitting, page 61A-7) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnpick the blower unit wiring harness (1) .
aUnclip the blower unit connector (2) .
aLift the blower unit connector.
aDisconnect the blower unit connector.aPress on the blower unit tab (3) .
aTurn the blower unit a quarter of a turn clockwise.
aRemove the blower unit (4) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the blower unit.
aPress on the blower unit tab.
aTurn the blower unit a quarter of a turn anti-clock-
wise.
aCheck that the blower unit is in place.
aConnect the blower unit connector. Equipment required
Diagnostic tool
119693
119694
119695

61A-54
HEATING
Fan assembly: Removal - Refitting
LEFT-HAND DRIVE
61A
aClip on the blower unit connector.
aClip on the blower unit wiring connector.
II - FINAL OPERATION.
aRefit:
-the front right-hand side air distribution duct (see
61A, Heating, Front side air distribution duct:
Removal - Refitting, page 61A-7) ,
-the passenger's front airbag (see Passenger's
frontal airbag: Removal - Refitting) (MR 411,
88C, Airbags and pretensioners).
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413 Fault finding, 88C, Airbags and pre-
tensioners).