battery RENAULT TWINGO RS 2009 2.G Chasiss Owner's Manual

37A-51
MECHANICAL COMPONENT CONTROLS
Clutch cable: Removal - Refitting
JB1
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the battery (see Battery: Removal - Refitting)
(MR 411, 80A, Battery),
-the battery tray (see Battery tray: Removal - Re-
fitting) (MR 411, 80A, Battery),
-the « brake pedal - clutch » assembly (see ) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the cable sleeve stop (1) from the bulkhead
and remove the passenger compartment cable.
aDetach the clutch cable at (2) .
aDetach the cable sleeve stop (3) from the fork on the
gearbox.
aDetach the clutch cable from the clutch fork at (4) .
aRemove the clutch cable.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the clutch cable.
aAttach the clutch cable to the clutch fork.
aFit the cable sleeve stop to the fork on the gearbox.
aAttach the clutch cable.
aFit the clutch cable through the opening in the bulk-
head and clip on the cable sleeve stop.II - FINAL OPERATION.
aRefit:
-the « brake pedal - clutch » assembly (see ) ,
-the battery tray (see Battery tray: Removal - Re-
fitting) (MR 411, 80A, Battery),
-the battery (see Battery: Removal - Refitting)
(MR 411, 80A, Battery).
121113

37A-63
MECHANICAL COMPONENT CONTROLS
Clutch circuit: Removal - Refitting
JH3
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove:
-the front wheel on the driver's side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) ,
-the front wheel arch liner on the driver's side (see
Front wheel arch liner: Removal - Refitting) (MR
412, 55A, Exterior protection),
-the battery (see Battery: Removal - Refitting)
(MR 411, 80A, Battery),
-the battery tray (see Battery tray: Removal - Re-
fitting) (MR 411, 80A, Battery).
aEmpty the brake fluid reservoir with a syringe.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aPress and hold the clip (1) .
aPull out the hydraulic clutch control pipe by one
notch.aPress and hold the clip (1) again.
aPull the hydraulic clutch control pipe out another
notch and collect the fluid in a container.
aDepress the clutch pedal to empty the hydraulic
clutch control circuit.
aDetach the pipe at (2) and (3) .
121354
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.
121118
121114

37A-64
MECHANICAL COMPONENT CONTROLS
Clutch circuit: Removal - Refitting
JH3
37A
aPull the clip (4) .
aUnclip the end piece (5) .
aRemove the hydraulic clutch control pipe.
aFit anti-contamination caps.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRemove the blanking plugs.
aRefit the clutch control pipe.
aFit the clutch control clip.
aConnect the pipe to the master cylinder and slave
cylinder.
II - FINAL OPERATION.
aBleed the clutch circuit (see 37A, Mechanical com-
ponent controls, Clutch circuit: Bleed, page 37A-
54) .
aTop up the brake fluid reservoir.
aCheck that the clutch system is operating correctly.
aRefit:
-the battery tray (see Battery tray: Removal - Re-
fitting) (MR 411, 80A, Battery),
-the battery (see Battery: Removal - Refitting)
(MR 411, 80A, Battery),-the front wheel arch liner on the driver's side (see
Front wheel arch liner: Removal - Refitting) (MR
412, 55A, Exterior protection),
-the front wheel on the driver's side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) .
121341

38C-2
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
K9K, and LEFT-HAND DRIVE
38C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aPosition the pedal press on the brake pedal to limit
the outflow of brake fluid.
aRemove:
-the front wheel on the passenger side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) ,
-the front wheel arch liner, on the passenger side
(see Front wheel arch liner: Removal - Refitting)
(MR 412, 55A, Exterior protection),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior
equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (MR 412, 56A, Exterior equipment),
-the air filter box (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture).aRemove:
-the bolts (1) from the lifting eye on the right-hand
side,
-the lifting eye on the right-hand side (2) ,
-the rigid pipe (3) from the EGR circuit.
aRemove the clip (4) from the soundproofing.
aMove the soundproofing aside (5) to access the hy-
draulic unit. Equipment required
pedal press
Tightening torquesm
hydraulic unit bolts on
its inter mediate bracket8 Nm
hydraulic unit inter medi-
ate bracket bolts on the
main hydraulic unit
mounting6.5 Nm
hydraulic unit main
mounting bolts on the
body8 Nm
rigid brake pipe unions
on the hydraulic unit13 Nm
112329
121358

38C-4
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
K9K, and LEFT-HAND DRIVE
38C
aRemove:
-the hydraulic assembly intermediate bracket bolts
(10) ,
-the « hydraulic unit intermediate bracket - hydraulic
unit » assembly (11) from the main mounting,
-the hydraulic unit bolts (12) from its intermediate
bracket,
-the hydraulic unit from its intermediate bracket.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the hydraulic unit onto its intermediate bracket,
-the hydraulic unit bolts onto its intermediate brack-
et.
aTorque tighten the hydraulic unit bolts on its inter-
mediate bracket (8 Nm).
aRefit:
-the « hydraulic unit intermediate bracket - hydraulic
unit » assembly onto the main mounting,
-the hydraulic unit intermediate bracket bolts onto
the main hydraulic unit mounting.
aTorque tighten the hydraulic unit intermediate
bracket bolts on the main hydraulic unit mount-
ing (6.5 Nm).aRefit:
-the « hydraulic unit mounting - hydraulic unit » as-
sembly on the body,
-the hydraulic unit main mounting bolts on the body.
aTorque tighten the hydraulic unit main mounting
bolts on the body (8 Nm).
II - FINAL OPERATION.
aRemove the blanking plugs.
aFit and tighten the rigid brake pipe unions on the hy-
draulic unit.
aTorque tighten the rigid brake pipe unions on the
hydraulic unit (13 Nm).
aConnect the computer connector on the hydraulic
unit.
aFit the bulkhead soundproofing.
aRefit:
-the soundproofing clip,
-the rigid exhaust gas recirculation circuit pipe,
-the lifting eye on the right-hand side,
-the air filter box (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (MR 412, 56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior
equipment),
-the front wheel arch liner, on the passenger side
(see Front wheel arch liner: Removal - Refitting)
(MR 412, 55A, Exterior protection),
-the front wheel on the passenger side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) .
aRemove the pedal press from the brake pedal.
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aBleed the braking circuit (see 30A, General infor-
mation, Braking circuit: Bleed, page 30A-4) .
121456

38C-5
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
D4F or D7F, and LEFT-HAND DRIVE
38C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aPosition the pedal press on the brake pedal to limit
the outflow of brake fluid.
aRemove:
-the front wheel on the passenger side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) ,
-the front wheel arch liner, on the passenger side
(see Front wheel arch liner: Removal - Refitting)
(MR 412, 55A, Exterior protection),
-the ignition coil (see Coils: Removal - Refitting)
(MR 411, 17A, Ignition),
-the fuel vapour recirculation circuit solenoid valve
(see Fuel vapour absorber: Removal - Refitting)
(MR 411, 14A, Emission control),
-the air filter box (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture).aDisconnect the hydraulic unit computer connector
(1) .
aUndo the rigid brake pipe unions (2) on the hydraulic
unit.
aInsert the blanking plugs. Equipment required
pedal press
Tightening torquesm
hydraulic unit bolts on
its inter mediate bracket8 Nm
hydraulic unit inter medi-
ate bracket bolts on the
main hydraulic unit
mounting6.5 Nm
hydraulic unit main
mounting bolts on the
body8 Nm
rigid brake pipe unions
on the hydraulic unit13 Nm
121359
121360
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.

38C-7
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
D4F or D7F, and LEFT-HAND DRIVE
38C
-the hydraulic unit main mounting bolts on the body.
aTorque tighten the hydraulic unit main mounting
bolts on the body (8 Nm).
II - FINAL OPERATION.
aRemove the blanking plugs.
aFit and tighten the rigid brake pipe unions on the hy-
draulic unit.
aTorque tighten the rigid brake pipe unions on the
hydraulic unit (13 Nm).
aConnect the computer connector on the hydraulic
unit.
aRefit:
-the air filter box (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture),
-the fuel vapour recirculation circuit solenoid valve
(see Fuel vapour absorber: Removal - Refitting)
(MR 411, 14A, Emission control),
-the ignition coil (see Coils: Removal - Refitting)
(MR 411, 17A, Ignition),
-the front wheel arch liner, on the passenger side
(see Front wheel arch liner: Removal - Refitting)
(MR 412, 55A, Exterior protection),
-the front wheel on the passenger side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) .
aRemove the pedal press from the brake pedal.
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aBleed the braking circuit (see 30A, General infor-
mation, Braking circuit: Bleed, page 30A-4) .

38C-8
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
D4F, and 780, and LEFT-HAND DRIVE – K4M, and LEFT-HAND DRIVE
38C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aPosition the pedal press on the brake pedal to limit
the outflow of brake fluid.
aRemove:
-the passenger side front wheel (see 35A, Wheels
and tyres, Wheel: Removal - Refitting, page
35A-1) ,
-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion).
aRemove the air filter housing (see Air filter unit: Re-
moval - Refitting) (12A, Fuel mixture).aDisconnect the fuel vapour rebreathing solenoid
valve union (1) .
aRemove the fuel vapour rebreathing solenoid valve
(2) .
aRemove the bolts (3) from the bulkhead heat shield.
aMove the bulkhead heat shield (4) to one side. Equipment required
pedal press
refrigerant charging station
Tightening torquesm
hydraulic unit bolts on
its inter mediate bracket8 Nm
intermediate bracket
bolts on the hydraulic
unit main bracket8 N.m
hydraulic unit main
mounting bolts on the
body8 Nm
rigid brake pipe unions
on the hydraulic unit13 Nm
D4F, and 780
109625
122384

38C-11
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
D4F, and 780, and LEFT-HAND DRIVE – K4M, and LEFT-HAND DRIVE
38C
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aBleed the brake circuit (see 30A, General informa-
tion, Braking circuit: Bleed, page 30A-4) .

38C-12
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
RIGHT-HAND DRIVE
38C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the battery (see Battery: Removal - Refit-
ting) (80A, Battery).aRemove:
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the battery tray (see Battery tray: Removal - Re-
fitting) (80A, Battery),
-the bolts (1) from the secondary brake fluid reser-
voir.
aMove aside the secondary brake fluid reservoir.
aRemove:
-the petrol injection computer (see Petrol injection
computer: Removal - Refitting) (17B, Petrol in-
jection),
-the computer mounting bolts,
-the computer bracket. Tightening torquesm
hydraulic unit bolts on
its inter mediate bracket8 Nm
hydraulic unit inter medi-
ate bracket bolts on the
main hydraulic unit
bracket8 Nm
hydraulic unit main
mounting bolts on the
body8 Nm
rigid brake pipe unions
on the hydraulic unit14 Nm
secondar y brake fluid
reservoir bolts8 Nm
123854
K4M