air filter RENAULT TWINGO RS 2009 2.G Electrical Equipment - Instrument Panel Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 66, PDF Size: 0.28 MB
Page 9 of 66
83A-9
MR-413-X44-83A000$112.mif
V5
INSTRUMENT PANEL
Fault finding - List and location of components
Vdiag No.: 04, 08
83A
2Warning light display:
1Brake warning light10“Service” warning light
2Major electric power-assisted steering fault
warning11
Rear fog lights indicator light
3Battery charge warning light12Front fog lights indicator light
4Oil pressure warning light13Direction indicator light
5Coolant temperature warning light14Passenger airbag disconnection warning light
6Particle filter warning light record
(Not used on the New Twingo)15Seat belt reminder indicator light
7On board diagnostics warning light16Door(s) open warning light
(Not present in the New Twingo)
8Airbag fault warning light17“Stop” warning light
9ABS warning light
Page 17 of 66
83A-17
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function
Vdiag No.: 04, 08
83A
–Illumination of the “Particle filter” warning light:
Illumination of the “Particle filter” warning light indicates a minor particle filter fault to the driver.
If the “Service” warning light and “Particle filter” warning light come on simultaneously, refer to the “Service warning
light illumination” insert.
The New Twingo does not currently have a particle filter.
–Illumination of the “Major Electric Power-Assisted Steering fault warning” warning light:
Illumination of the “major electric power-assisted steering fault warning” warning light is requested by the electric
power-assisted steering up to 1 second after the engine is started.
If the “Stop” warning light and “Stop buzzer” are activated simultaneously, refer to the “Stop warning light
illumination” insert.
–Illumination of the “OBD” warning light
If the “OBD” warning light and “Service” warning lights come on simultaneously, refer to the “Service warning light
illumination” insert.
–Illumination of the “airbag fault” warning light:
Illumination of the “Airbag fault” warning light indicates an airbag warning light test phase by the instrument panel.
If the “Service” warning light and “Airbag fault” warning light come on simultaneously, refer to the “Service warning
light illumination” insert.
–Illumination of the “Passenger airbag disconnection” warning light:
Illumination of the “Passenger airbag disconnection” warning light indicates deactivation of the front passenger
airbag.
Page 20 of 66
83A-20
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function
Vdiag No.: 04, 08
83A
“Service” warning light + “ABS” warning light:
–ABS fault warning.
“Service” warning light + “Particle filter” warning light:
–“Major particle filter fault” warning.
The New Twingo does not currently have a particle filter.
“Service” warning light + “OBD” warning light:
–“Combustion misfire” warning.
“Service” warning light + “OBD” warning light flashing:
–“Destructive combustion misfire” warning.
“Service” warning light + “Airbag fault warning” warning light:
–“Airbag fault” warning.
“Service” warning light + “Sinusoid” warning light:
–“Minor injection fault” warning.
–“Water in diesel fuel” warning (on diesel configuration only).
–“Sequential gearbox fault” warning (on sequential gearbox configuration only).
Page 24 of 66
83A-24
MR-413-X44-83A000$448.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Interpretation of faults
DF007
PRESENT
OR
STOREDFUEL SENDER CIRCUIT
CO : Open circuit
CC : Short circuit
1.DEF : Internal electronic fault
2.DEF : Battery undervoltage
NOTES1.DEF: Contact Techline.
2.DEF: Carry out fault finding on the charging circuit (see Technical Note 6014A,
Checking the charging circuit).
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after waiting for 1 second, with the ignition on, then
stored after 60 seconds.
Special note:
Check the consistency between the instrument panel display and parameter PR041
Filtered fuel level.
CO
CC
NOTESSpecial note:
CO: The fault is declared present if the fuel sender
resistance is greater than 350 Ω.
CC: The fault is declared present if the fuel sender
resistance is less than 5 ΩΩ Ω Ω
.
Manipulate the wiring harness between the instrument panel and the fuel sender in order to produce a change in
fault status (Present → Stored).
Look for possible damage to the wiring harness, and check the connection and condition of the fuel sender and
its connections.
Look for possible damage to the wiring harness, check the connection and condition of the instrument panel
connector.
If there is a repair method (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair)
repair the connector, otherwise replace the wiring.
Check the 30A fuse of the positive protected battery, component code 1033.
Measure the resistance between connections 41A and 41B of the fuel sender.
Replace the fuel sender if the resistance value is not: 260 ΩΩ Ω Ω
fuel tank in reserve
38 ΩΩ Ω Ω
fuel tank full
(see MR 411, 19C, Tank, fuel sender: Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_DF007 / TDB_V08_DF007
Vdiag No.: 04, 08
MR-413-X44-83A000$448.mif
Page 30 of 66
83A-30
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check
Vdiag No.: 04, 08
83A
SUB-FUNCTION: DISPLAY (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Fault signalET249:Service warning
light activated by
the system1-Multiplex line
communication
2- Injection
3-Water present in diesel
fuel
4-Sequential gearbox
5-Vehicle speed circuit
6-Cruise control/speed
limiter
7-ESP
8-ABS
9-Oil change interval
10- Particle filter
11- Airbag
12- OBDSee the interpretation of
ET249 SERVICE warning
light activated by the
system
Parking brake
signalET097:Parking brakeAutomatic
parking brake
onAPPLIED
In the event of a fault, consult
the interpretation of status
ET097 Parking brake Parking
brake
releasedRELEASED
Minimum brake
fluid level signalET019:Minimum brake
fluid levelMinimum
brake fluid
reservoir
levelYES
In the event of a fault, consult
the interpretation of status
ET019 Minimum brake fluid
level. Normal brake
fluid
reservoir
levelNO
Oil pressure
present signalET096:Oil pressure
contactEngine
runningOPENIn the event of a fault,
consult the interpretation of
fault DF009 “oil pressure
sensor” Engine
stoppedCLOSED
Page 34 of 66
83A-34
MR-413-X44-83A000$560.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Status summary table
*ADAC: Trip Computer Tool status Diagnostic tool title Specification
ET004Side lights control Inactive/Active
ET019Minimum brake fluid level Yes/No
ET030ADAC* scroll button Released/Pressed
ET095Clock setting button Released/Pressed
ET097Parking brake Engaged/Released
ET245Direction indicators Inactive/Active
ET248Stop warning light activated by the
system1 : Injection
2 : Coolant temperature
3 : Oil pressure
4 : Brake fluid level
5 : Electronic Braking Distribution
6 : Electric power assisted steering
7 : Battery charge
ET249Service warning light activated by the
system1 : Multiplex line communication
2 : Injection
3 : Water present in diesel fuel
4 : Sequential gearbox
5 : Vehicle speed circuit
6 : Cruise control/speed limiter
7 : ESP
8 : ABS
9 : Oil service interval
10 : Particle filter
11 : Airbag
12 : OBD
Vdiag No.: 04, 08
MR-413-X44-83A000$560.mif
Page 42 of 66
83A-42
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses
Vdiag No.: 04, 08
83A
ET249
SERVICE WARNING LIGHT ACTIVATED BY THE SYSTEM
If the SERVICE WARNING LIGHT is illuminated, check for faults and check the conformity of the systems
concerned.
1 : Multiplex line communication
Check the multiplex network (see 88B, Multiplex)
2 : Injection
3 : Water present in diesel fuel
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
4 : Sequential gearbox
Carry out fault finding on the sequential gearbox (see 23A, Sequential gearbox).
5 : Vehicle speed circuit
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
6 : Cruise control/speed limiter
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
7 : ESP
8 : ABS
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
9 : Oil service interval
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
10 : Particle filter
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
11 : Airbag
Carry out fault finding on the Airbag system (see 88C, Airbag and pretensioners).
12 : OBD
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
If there are no faults, carry out a multiplex network check (see 88B, Multiplex).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET249 / TDB_V08_ET249
Page 44 of 66
83A-44
MR-413-X44-83A000$728.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Interpretation of parameters
PR041 Filtered fuel level
NOTESIn the event of a fuel sender fault, check for the presence of DF007 FUEL SENDER
first.
This value is used to display the fuel level, i.e. the number of illuminated squares on the instrument panel.
Reference table displaying the filtered fuel level (PR041) in relation to the number of illuminated squares.
–0l to 5l: reserve square
–5l to 8l: 1 square
–8l to 12l: 2 squares
–12l to 18l: 3 squares
–18l to 25l: 4 squares
–25l to 32l: 5 squares
–32l to 37l: 6 squares
–37l to full: 7 squares
IMPORTANT
Once a square is no longer lit, it can not be relit except by adding fuel to the tank or running command VP020
UPDATE FUEL LEVEL DISPLAY.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_PR041 / TDB_V08_PR041
Vdiag No.: 04, 08
MR-413-X44-83A000$728.mif