change time RENAULT TWINGO RS 2009 2.G Electrical Equipment - Multimedia Connection Workshop Manual

8Electrical equipment
V1 MR-413-X44-86C000$TOC.mif
V1
86C
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
V1
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s. 2009
MULTIMEDIA CONNECTION
CBOX
Vdiag No.: 04
Fault finding – Introduction 86C - 2
Fault finding – List and location of components 86C - 8
Fault finding – Role of components 86C - 14
Fault finding – Operating diagram 86C - 15
Fault finding – Function 86C - 18
Fault finding – Configuration 86C - 19
Fault finding – Programming 86C - 20
Fault finding – Fault summary table 86C - 21
Fault finding – Interpretation of faults 86C - 22
Fault finding – Conformity check 86C - 32
Fault finding – Status summary table 86C - 33
Fault finding – Parameter summary table 86C - 34
Fault finding – Command summary table 86C - 35
Fault finding – Customer complaints 86C - 36
Fault finding – Fault Finding Chart 86C - 37

86C -5V1 MR-413-X44-86C000$010.mif
MULTIMEDIA CONNECTION
Fault finding – Introduction86C
CBOX
Vdiag No.: 04
4. FAULT FINDING PROCEDURE (continued)
4.1. Wiring check
Fault finding problems
Disconnecting the connectors and/or manipulating the wiring may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Physical inspection
When handling the wiring, use the diagnostic tool to detect any change in the status of the fault from "stored" to
"present".
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Checking earth insulation
This check is carried out by measuring the voltage (multimeter in voltmeter mode) between the suspect connection
and the 12 V or 5 V. The correct measured value is 0 V.
Checking insulation against + 12 V or + 5 V
This check is carried out by measuring the voltage (multimeter in voltmeter mode) between the suspect connection
and the earth. In the first instance, the earth may be taken on the chassis. The correct measured value should be 0 V
Continuity check
A continuity check is carried out by measuring the resistance (multimeter in ohmmeter mode), with the connectors
disconnected at both ends. The expected result must be between: 0 ΩΩ Ω Ω
< X < 2 Ω for every connection. The line must
be fully checked, and the intermediate connections are only included in the method if this saves time during the fault
finding procedure. The continuity check on the multiplex lines must be carried out on both wires. The measured
value must be between: 0 ΩΩ Ω Ω
< X < 2 ΩΩ Ω Ω
.
Checking the supply
This check may be carried out using a test light (21 W or 5 W depending on the maximum authorised load)

86C-18V1 MR-413-X44-86C000$050.mif
86C
CBOX
Vdiag No.: 04
The mobile connectivity computer enables music files to be played (MP3, WMA, etc.) on:
•USB mobile peripherals (USB key, MP3 player, etc.) (Except hard disk with own power supply),
•audio peripherals via the jack socket.
The multimedia system offers the following possibilities:
•Choose FM radio stations using the presets, the list or manual selection.
•Have access to an automatically updated FM radio list.
•Listen to CDs and MP3s.
•Control the radio using the radio control satellite.
•Have access to optimised audio and acoustic telephone configurations for each vehicle according to the vehicle
type.
•Modify various acoustic parameters (base, treble, front/rear balance, etc.).
•Use the hands-free telephone function (sound relayed towards the radio speakers) with a Bluetooth telephone.
•Use voice recognition for the telephone functions (button on the radio control satellite). The voice identifier can be
recorded.
•Benefit from a connection for a CD changer.
•Possibility of connecting a peripheral with a USB port, Jack socket, etc.
•Has anti-theft protection
Computer activation system
The mobile connectivity computer has an activation system.
The mobile connectivity computer is activated under the following conditions:
•by pressing the radio ON/OFF button,
•by starting the engine.
The mobile connectivity computer is switched off under the following conditions:
•The ignition is switched off.
•Door opened (Clio III)
•Door opened for 1 minute (New Twingo)
•By pressing the radio ON/OFF button (Clio III and New Twingo).
The multimedia connection unit (Display or Multimedia connection unit ) is activated by the UCH (central door
unlocking); this then activates the multimedia computers (Navigation, Radio, mobile connectivity computer, etc.) via
the "Activation signal" connections.
MULTIMEDIA CONNECTION
Fault finding – Function