key RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD User Guide

87B-20
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
This scenario is used to check the status of the key in the event of a blank or not blank UCH.
It tells you:
–if the key is blank (ET182 BLANK KEY),
–if the key is allocated to this vehicle or not (ET181 KEY ALLOCATED TO THE VEHICLE),
–If the key is a memory type (ET407 MEMORY KEY).
1
st solution:
2
nd solution:
3
rd solution:SC018
CHECKING A KEY
Equipment required
CLIP
Blank keyNO
This key is not blank but is allocated to the
vehicle, therefore the key is operational.
Check with the key statuses in the protection
sub-function (see conformity check in the
event of a fault). Key allocated to the vehicleYES
Memory keyYES/NO
Blank keyYES
This key is blank, allocate the key using
command SC015 KEY ALLOCATION to
allow it to be used on the vehicle. Key allocated to the vehicleNO
Memory keyYES/NO
Blank keyNOThis key is not blank, and it does not belong
to this vehicle. It is impossible to allocate this
key to the vehicle.
Or:
If the UCH is being replaced, this key belongs
to the vehicle but is no longer allocated, so
run command SC015 KEY ALLOCATION. Key allocated to the vehicleNO
Memory keyYES/NO

87B-21
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
Functions available and operating mode
–Deadlocking (CF009)
This function enables you to disable the interior door opening control. This function is activated by a second locking
request from the key or the electric central locking switch.
This function is only available on vehicles fitted with a top of the range UCH.
–Hazard warning lights activated by ABS (CF024)
This function is available for all countries except Brazil, Finland, Great Britain, Japan and Sweden.
For Brazil, Great Britain, Japan, Sweden and Finland configure NONE.
For other countries, configure WITH.
In the event of braking causing rapid deceleration, the ABS computer transmits an activate hazard warning lights
request via the multiplex network to the UCH.
–New vehicle storage mode (LC041 New vehicle storage mode)
If this mode is activated, consult the command, see LC041 "New vehicle storage mode" and contact the Techline.
–Daytime running lights
This configuration automatically activates the side lights and dipped beam headlights when the engine is running,
without the driver using the lighting controls.
To be used in accordance with legislative requirements.
CF031 Calibration:
When replacing the UCH computer, perform this configuration.
This command lasts approximately 30 seconds.

87B-22
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
UCH CONFIGURATIONS
List of individual configurations available on the diagnostic tool with the associated configuration reading.
* SR: Sunroof.
*RF: radio frequencyConfigurationConfiguration
readingName of configuration Choice of configuration
CF031 "Calibration",To be performed if replacing
the UCH.
CF019 LC013"Type of heating and air conditioning
system",HEATING/MANUAL/
AUTOMATIC
CF028 LC023 "Engine type",Configuration. 1 (K9K)
Configuration. 2 (D7F/D4F
without air conditioning)
Configuration. 3 (other engine)
CF171 LC067 "Temperature display"WITH/WITHOUT
CF029 LC002 "Exterior temperature sensor",WITH/WITHOUT
CF173 LC070 "One-touch windows/SR*",WITH/WITHOUT
CF032 LC025 "See-me-home lighting",WITH/WITHOUT
CF021 LC015 "Front fog lights"WITH/WITHOUT
CF014 LC008 "Daytime running lights",WITH/WITHOUT
CF193 LC095 "Automatic headlighting function",WITH/WITHOUT
CF194 LC096 "Automatic wiping function",WITH/WITHOUT
CF035 LC044 "Rain/light sensor", PRESENT/ABSENT
CF191 LC094 "Wiper intermittent speed ring",WITH/WITHOUT
CF024 LC018"Hazard warning lights switched on by
ABS",WITH/WITHOUT
CF108 LC040 "Automatic locking when driving",WITH/WITHOUT
CF009 LC003 "Deadlocking",WITH/WITHOUT
CF192 LC093 "Central door locking",WITH/WITHOUT
CF195 LC097 "Type of key". STANDARD/RF*
CF229 LC126 "Alarm".WITH/WITHOUT

87B-23
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
Procedure to follow for modifying these configurations
–Establish dialogue with the UCH.
–Select the Repair mode menu.
–Select the Enter configuration menu.
–Select the line corresponding to the configuration to be modified.
–In the drop-down menu, select the line corresponding to the vehicle's equipment or the customer's selection.
–Click on Confirm.
In the Read configuration menu, check that the configuration has been completed.
Note:
If the configuration LC089 Memory key function is WITH and if status ET407 Memory key (displayed using
command SC018 Key check) is YES, then the UCH computer can be used to handle information about the
vehicle contained in the key.

87B-38
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
*RF: radio frequencyDF054
PRESENT
OR
STORED
COMPUTER
The radiofrequency receiver inside the UCH computer does not work
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
–The fault is declared present after the ignition has been switched on.
If the fault is stored, switch off the ignition and check the F8 (15A) fuse of the UCH supply (component
code 645) on the passenger compartment fuse and relay box (component code 1016).
–Replace the fuse if necessary, clear the fault and switch on the ignition again.
–Request locking and then unlocking, then start the engine.
Check for + after ignition feed on connections AP43, BP15, APT, BP6, BP13, BP19, SP2, SP15 of
component 645.
Check for + 12 V accessories feed on connections SP2 and SP15 of component 645.
Check for earth on connections MAN and NAM of component 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that status ET045 “RF* signal received” is “Yes” by pressing the locking button on the key, if when
pressing the status is “No” check the battery and the conformity of the key.
If the fault does not reappear, switch the lighting, wipers, vehicle locking and climate control request controls on
and off several times, then read the faults again.
If the fault is still present. Do not operate on the computer, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF054

87B-69
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: PROTECTION
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
Engine
immobiliserET046:Engine immobiliserINACTIVE = Vehicle
unprotected, ready to start.
ACTIVE = Vehicle protected,
starting impossible.In the event of a fault, refer to
the interpretation of status
ET046.
And (see 87B, Passenger
compartment
connection unit).
ET008:blank UCHYES = If the UCH is blank.
NO = If the UCH has been
programmed with an
immobiliser code.In the event of a fault, refer to
the interpretation of status
ET008.
And (see 87B, Passenger
compartment
connection unit).
KeyET185:Key code receivedYES = If the UCH has received
the immobiliser code from the
key.
NO = If the UCH does not
receive the immobiliser code
from the key.In the event of a fault, refer to
the interpretation of status
ET185.
And (see 87B, Passenger
compartment
connection unit).
ET181:Key allocated to the
vehicleYES = The key is allocated to
the vehicle.
NO = The key is not allocated
to the vehicle.In the event of a fault, refer to
the interpretation of status
ET181.
And (see 87B, Passenger
compartment
connection unit).

87B-70
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: PROTECTION (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
KeyET045:Radio frequency
signal receivedYES = When the UCH receives
a radiofrequency signal.
NO = When the UCH does not
receive a Radiofrequency
signal.In the event of a fault, refer to
the interpretation of status
ET045.
ET193:Radiofrequency
signal from a key
allocated to the
vehiclePRESENT =
Reception of a signal
Radiofrequency signal from a
key allocated to the vehicle.
ABSENT =
No reception of signal
Radiofrequency or signal
Radiofrequency signal from a
key not allocated to the vehicleIn the event of a fault, refer to
the interpretation of status
ET193.
ET240:Key frequency (in
MHz)433
NONEIf NONE, refer to the
interpretation of status
ET240.
PR056:Number of keys
allocatedX ≤ 4 key(s)In the event of a fault, refer to
the interpretation of fault
PR056.
InjectionET229:Injection immobiliser
codePROGRAMMED
NOT PROGRAMMED
UNDETERMINEDIn the event of a fault, consult
the interpretation of status
ET229.
ET250:InjectionNOT PROTECTED
PROTECTEDIn the event of a fault, refer to
the interpretation of status
ET250.
(See 17B, Petrol Injection,
Conformity check,
Protection) or (see 13B,
Diesel Injection, Conformity
check, Protection).
Starter actuatorET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition feed.
+ START FEEDIn the event of a fault, refer to
the interpretation of status
ET239.

87B-71
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: ACCESS
* SR: Sunroof.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
TailgateET061:Open tailgate
requestPRESENT
ABSENTIn the event of a fault, apply the
interpretation of status
ET061.
ET463:Door(s) or tailgateOPEN
CLOSEDIn the event of a fault, apply the
interpretation of status
ET463.
Locking/unlocking
buttonET186:Short press on door
closing buttonSignal can be
interpreted if the
ignition is switched off
(key removed from the
ignition switch).
ACTIVE = Remote
control door closing
button pressed for
longer than 2 seconds.
INACTIVE = Button not
pressed or pressed for
less than 2 seconds.In the event of a fault, refer to
the interpretation of status
ET186.
ET189:Long press on door
opening buttonACTIVE
INACTIVEIn the event of a fault, refer to
the interpretation of status
ET189.
Electric central locking
buttonET044:Central Locking
buttonDEPRESSED
RELEASEDIn the event of a fault, refer to
the interpretation of status
ET044.
One touch window /
SR*.ET087:One-touch window /
SR* authorisation.PRESENT
ABSENTIn the event of a fault, apply the
interpretation of status
ET087.
Locking commandAC004:Central door lockingThis command is used
to test whether central
door locking is workingIn the event of a fault, consult
the procedure for dealing
with command AC004.

87B-85
MR-413-X44-87B000$528.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table87B
*SR: Sunroof.
*RF: radio frequencyTool status Diagnostic tool title
ET084Right-hand indicator request
ET085Hazard warning lights button
ET087One-touch window/SR* authorisation
ET096Wiper intermittent speed ring position
ET097Rear screen wiper park position
ET109Reverse gear engaged
ET111Front fog lights request
ET114Wiping request via rain sensor
ET115Request to switch on lights by light sensor
ET142Engine operating phase
ET181Key allocated to the vehicle
ET185Key code received
ET186Short press on door closing button
ET189Long press on door opening button
ET193RF* signal from a key allocated to the vehicle
ET229Injection immobiliser code
ET239Ignition switch position
ET240Key frequency (in Hz)
ET250Injection
ET463Door(s) or tailgate

87B-86
MR-413-X44-87B000$576.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
ET008
BLANK UCH
NOTESNo faults should be present or stored.
SPECIFICATIONSYES
NO
ET008 is YES.
Program the UCH using SC004 Program UCH.
Apply the procedure after replacing the computer (see Replacement of components).
ET008 is NO.
If the UCH is not blank and has just been replaced, check whether the key is allocated (use command SC018 Key
check).
If the key is not allocated, allocate the keys using command SC015 Key allocation.
If the key is allocated, the UCH is operational.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET008
MR-413-X44-87B000$576.mif
UCH
Vdiag No.: 44