diagnostic menu RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Workshop Manual

87B-15
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
UCH programming procedure
–Establish dialogue with the UCH.
–Select the "Repair mode" menu.
–Select the Secure programming menu.
–Select line SC004 Program UCH.
Follow the instructions on the CLIP diagnostic tool.
In "not connected" mode, when the CLIP diagnostic tool displays the programming key, make a note of this key
and the VIN.
To obtain the immobiliser code, see Technical Note 5037A, Code delivery procedure.
Operations to be carried out after programming the UCH
➡ Enter the vehicle's VIN to the computer using command VP004 Enter VIN.
Make sure that all the keys can lock and start the vehicle.
➡ After programming the UCH, allocate all the keys using command SC015 Allocate key.
➡ Configure the equipment as present or not present on the vehicle using the commands
(see Configurations and Programming). SC004
CONTINUED
IMPORTANT
Do not interrupt the procedure when it is in progress.
If it is interrupted, restart the procedure; a new programming key will be displayed.
IMPORTANT
In "not connected" mode, the programming key can only be used for a limited amount of time, as indicated by the
CLIP diagnostic tool. After this time, the programming key and associated immobiliser code are no longer valid.
The operation must be restarted from the beginning.

87B-17
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
Key allocation procedure
–Establish dialogue with the UCH
–Select the Repair mode menu
–Select the Secure programming menu
–Select line SC015 Allocate key.
The procedure for allocating keys is divided in two parts:
1Key insertion stage.
2Key allocation stage.
1 - Key insertion stage
Clip requests that the keys to be allocated are inserted.
Insert ALL the keys to be allocated (old and new blank keys); any keys not inserted at this stage will be rejected in
the Key allocation stage and the operation will have to be restarted from the beginning.
Once all the keys are inserted, the Clip diagnostic tool displays the programming key.
To obtain the immobiliser code, see Technical Note 5037A, Code delivery procedure.
2 - Key allocation stage:
Continue the procedure following the instructions on the CLIP diagnostic tool.
Once the keys have been allocated, make sure that all the keys can lock and start the vehicle.SC015
CONTINUED
IMPORTANT
In "not connected" mode, once the tool has issued the programming key, the user has a limited amount of time in
which to enter the immobiliser code.
If this time expires, the CLIP diagnostic tool displays the message "Time expired. Restart the procedure''.
IMPORTANT
In "connected" mode, the exchange of the programming key and the entry of the immobiliser code is done
automatically.
If the connection parameters are not met, "connected" mode switches automatically to "not connected" mode.
IMPORTANT
The programming key can only be used for a limited time, as shown by the Clip diagnostic tool. After this time,
the programming key and associated immobiliser code are no longer valid. The operation must be restarted from
the beginning.

87B-19
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
Injection immobiliser code programming procedure:
–Establish dialogue with the UCH
–Select the Repair mode menu
–Select the Secure programming menu
–Select line SC017 Program injection immobiliser code.
Follow the instructions on the CLIP diagnostic tool.
When the CLIP diagnostic tool displays the programming key, make a note of this key and the VIN code.
To obtain the immobiliser code, see Technical Note 5037A, Code delivery procedure. SC017
CONTINUED
IMPORTANT
The programming key can only be used for a limited time, as shown by the Clip diagnostic tool. After this time,
the programming key and associated immobiliser code are no longer valid. The operation must be restarted from
the beginning.
IMPORTANT
In "not connected" mode, once the tool has issued the programming key, the user has a limited amount of time in
which to enter the immobiliser code.
If this time expires, the CLIP diagnostic tool displays the message "Time expired. Restart the procedure''.
IMPORTANT
In "connected" mode, the exchange of the programming key and the entry of the immobiliser code is done
automatically.
If the connection parameters are not met, "connected" mode switches automatically to "not connected" mode.