relay RENAULT TWINGO RS 2009 2.G Heating And Air Conditioning - Manual Air Conditioning Workshop Manual

62C-18
MR-413-X44-62C000$455_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Function62C
Vehicle
multiplex
network
Heated rear screen
resistor relay
Summary of components controlled or managed by the MANUAL AIR CONDITIONING control panel:
Ventilation and air conditioning unit
Passenger
compartment
blower
Resistor
unitRecirculation
flapDistribution
flapMixing
flap
Actuator control
User control panel
User request management
(air conditioning button and
heated rear screen button
pressed)Button lighting (air conditioning
button and heated rear screen
button)Passenger compartment
blower operation signal
(running or stopped)
UCH
Transmission of air conditioning
request
Activation of the heated rear
screen request.
Key:
Wire connections =
Multiplex connections =
Mechanical connections =
(control cables)

62C-19
MR-413-X44-62C000$455_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Function62C
Vehicle
multiplex
network
Summary diagram of components controlled or managed by the UCH:
Summary diagram of components controlled or managed by the injection computer Rear screen de-icing and
rear-view mirror de-icer
(depending on version)External temperature
sensor
(depending on
version)
Actuator control Sensor management
UCH
Air conditioning request
managementHeated rear screen control
management
Relay No. 1 for
the Passenger
Compartment
Heating
ResistorsRelay No. 2 for
the Passenger
Compartment
Heating
ResistorsAir conditioning
compressorEngine cooling
fan assemblyEngine
coolant
temperature
sensorRefrigerant
fluid
pressure
sensor
Actuator control Sensor management
Engine injection computer
Management of the cold loop (refrigerant pressure, engine cooling fan activation request,
compressor activation authorisation, etc.)
Key:
Wire connections =
Multiplex connections =

62C-34
MR-413-X44-62C000$637_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Conformity check62C
SUMMARY TABLE OF THE VARIOUS AIR CONDITIONING COMPUTER COMMANDS
Fault finding procedures for the commands listed in this summary are explained in the Workshop Repair Manuals
relating to the computer which generates the signal (see Introduction). Name of sub-function Name of computer Command name Fault finding
COLD LOOPInjection (see 13B, Diesel
injection or 17B, Petrol
injection)AC180: Air conditioning
compressor relay
controlIn the event of a fault, refer
to the interpretation of
this command.
AC153 High speed fan
assemblyIn the event of a fault, refer
to the interpretation of
this command.
AC154 Low speed fan
assemblyIn the event of a fault, refer
to the interpretation of
this command.
HEATINGUCH (see 87B,
Passenger
compartment
connection unit)AC060 Rear screen de-
icerIn the event of a fault, refer
to the interpretation of
this command.
Injection (see 13B, Diesel
injection or 17B, Petrol
injection)AC250 Heating resistor
relay 1In the event of a fault, refer
to the interpretation of
this command.
AC251 Heating resistor
relay 2In the event of a fault, refer
to the interpretation of
this command.
USER SELECTIONUCH (see 87B,
Passenger
compartment
connection unit)AC015 Air conditioning
button indicator lightIn the event of a fault, refer
to the interpretation of
this command.
AC019 Heated rear
screen indicator lightIn the event of a fault, refer
to the interpretation of
this command.

62C-46
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
ALP 5
CONTINUED 4
Using a test light, check for + 12 V between connection SP2 and earth MAM.
Is the test light lit?
YES NO
Using a test light, check for + 12 V between
connection BP1 of component 1428 and a chassis
earth.Using a test light, check for + 12 V between
connnection SP2 and a chassis earth.
Is the test light lit? Is the test light lit?
YES NO YES NO
Activate speed 1 and,
using a test light, check for
+ 12 V between
connection SP3 of
component 1156 and a
chassis earth.Carry out a continuity
test on connection
BP1 between
component 1428 and
fuse
F24 (30A) of
component 1016.Fault on connection MAM.
Repair the wiring. If there is a
repair procedure (see Technical
Note 6015A, Repairing
electrical wiring, Wiring:
Precautions for repair), repair
the wiring, otherwise replace it.Carry out a
continuity test
on connection
SP2 between
component
1428 and fuse
F29-15A of
component
1016 Is the test light lit? Is the continuity
correct?
YES NO YES NO
Replace the
fan assembly.Replace the
fan assembly
relay.Fault on connection MAM.
Repair the wiring. If there is
a repair procedure (see
Technical Note 6015A,
Repairing electrical
wiring, Wiring:
Precautions for repair),
repair the wiring, otherwise
replace it.
D
Is the continuity correct?
YES NO
AFTER REPAIRCarry out a complete check with the diagnostic tool.

62C-51
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
ALP 8
CONTINUED 3
Carry out fault finding on the injection system to ensure that no fault is present (if faults are displayed by the
injection computer, engagement of the air conditioning may be inhibited). If there are present or stored faults,
carry out the necessary repairs (see 13B, Diesel injection or 17B, Petrol injection).
Check that the refrigerant fluid pressure is correct (neither too low nor too high) using the PR037 Refrigerant
fluid pressure parameter (see Conformity check, Cold loop sub-function).
Check that the engine cooling fan assembly is at
speed 1 by viewing the following status on the cold
loop sub-function screen:
–Status ET022 Low-speed fan assembly request
should display ACTIVE.
Note:
These statuses are not displayed by all types of
injection (see Conformity check, Cold loop sub-
function).
Does the engine cooling fan operate at low speed?
YES
NOUsing the diagnostic tool, run
command AC154 Low speed fan
assembly relay.
Does the engine cooling fan operate
at low speed?
NO YES
Connector of component 321 disconnected. Connect a
test light between connection 49L of component 321
and the chassis earth and run command AC154 Low
speed fan assembly relay.
Does the test light illuminate?
YES NO
Measure the resistance of component 321, between
connections 49L and 49B of component 321. If the
resistance measured is infinite, replace the fan assembly
resistor (component 321).
Carry out fault
finding on the
injection system
(sub-function: cold
loop and engine
cooling for low
speed fan assembly
activation).
D
AFTER REPAIRCarry out a complete check with the diagnostic tool.

62C-52
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
ALP 8
CONTINUED 4
Check the continuity of connection 49L between components 321 and 700.
Is the continuity correct?
NO YES
Continuity fault on connection 49L. If there is a repair
procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.Check that the low speed fan assembly relay operates
correctly (component 700). Replace it if it is faulty (see
MR 411 Mechanical, 81C, Fuses, Fuses: List and
location of components).
D
AFTER REPAIRCarry out a complete check with the diagnostic tool.

62C-53
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
ALP 8
CONTINUED 5
Check the air conditioning compressor belt tension
(see Technical Note 3786A, Engine and
peripherals, 10A, Belt tension setting tool Hz
measurement: tension values).
Is the tension correct?
YES
With the engine stopped, use the diagnostic tool to
run command AC180 Air conditioning
compressor relay (injection command mode
menu).
Does the compressor clutch jam?
YES
E
NOReplace the belt (see MR 411
Mechanical, 11A, Top and front of
engine, Accessories belt:
Removal - Refitting).
NO
YESConnect a test light between connections 38R
and MAS of component 171 and run
command AC180 Air conditioning
compressor relay.
Does the test light illuminate?
NO
Connect a test light between connection 38R
of component 171 and the chassis earth, then
run command AC180 Air conditioning
compressor relay.
Does the test light illuminate?
YES
Earth fault on component 171.
If there is a repair procedure
(see Technical Note 6015A,
Repairing electrical wiring,
Wiring: Precautions for
repair), repair the wiring,
otherwise replace the wiring.
Check the condition of the
diode (component 322).
Replace the diode if it is faulty.
Replace the air conditioning
clutch (component 171) if
possible, otherwise replace
the compressor (see MR 411
Mechanical, 62A, Air
conditioning, Compressor:
Removal - Refitting).
NO
F

62C-54
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
ALP 8
CONTINUED 6
Check the continuity and insulation to earth of connection 38R between components 171 and 584.
Is the connection OK?
YES NO
Apply the fault finding procedure for command AC180
Air conditioning compressor relay (see 13B Diesel
injection or 17B Petrol injection).If there is a repair procedure (see Technical Note
6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise
replace it.
F
AFTER REPAIRCarry out a complete check with the diagnostic tool.

62C-56
MR-413-X44-62C000$910_eng.mif
V1
62C
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts
ALP 9 Too much cold air
NOTESConsult this customer complaint after a full check with the diagnostic tool (fault reading and
configuration checks).
Check that the fuses are sound.
Use a multimeter and a 21 W test light.
Use the Wiring Diagram Technical Note, New Twingo.
With the engine at idle speed and the heating and air conditioning off (AC button not pressed), check that the air conditioning
compressor clutch is not engaged.
Is the air conditioning compressor clutch engaged? NO
YES
With the engine stopped, check that the compressor clutch electric control operates correctly, using the diagnostic tool to run
command AC180 Air conditioning compressor relay (injection command mode menu).
–During the command, connection 38R of component 171 must be supplied with + 12 V.
–After the command, connection 38R of component 171 must no longer be supplied with + 12 V.
Is the connection still supplied with + 12 V after the command?
YES NO
Check the continuity and insulation from + 12 V of
connection 38R between components 171 and 584.Check that the air conditioning compressor clutch is not
jammed (mechanical fault).
Is the connection OK? Is the clutch still engaged?
NO YES YES
If there is a repair procedure (see
Technical Note 6015A, Repairing
electrical wiring, W iring:
Precautions for repair), repair the
wiring, otherwise replace it.With the vehicle ignition of f, check that
the compressor clutch relay is not
“jammed”, by checking the continuity
between connection 38R and
connection AP3 of component 584.
Is the continuity present?
NO

Apply the fault finding procedure for command
AC180 Air conditioning compressor relay
(see 13B Diesel injection or 17B Petrol
injection).
Is the fault still present?
Replace the air conditioning
compressor (see MR 411,
Mechanical, 62A, Air conditioning,
Compressor: Removal - Refitting).
YESReplace the air
conditioning
compressor clutch
relay.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
MR-413-X44-62C000$910_eng.mif