ESP RENAULT TWINGO RS 2009 2.G Mechanism And Accessories Workshop Manual

52A-7
NON-SIDE OPENING ELEMENT MECHANISMS
Sunroof operating mechanism: Removal - Refitting
52A
aRemove:
-the bolts (2) ,
-the sunroof console mounting.
aProtect the vehicle interior.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aProtect the sunroof frame using masking tape.
ainsert the threading needle preferably at the front left
or right of the sunroof operating mechanism.
aCut the cement bead (this operation requires two
people).
aRemove the sunroof operating mechanism using the
specific support (x2):
-Support: PARV 202,
-arch sets: APARV 200 ESP.
REFITTING
I - REFITTING PREPARATION OPERATION
aFor preparation and bonding see Technical Note
560A, General procedure for bonding windows
and sunroof.
aPosition:
-the two centring guides on the sunroof operating
mechanism,
-the positioning shims on the periphery of the sun-
roof operating mechanism.
II - REFITTING OPERATION FOR PART
CONCERNED
aPosition the cement bead at the interior roof panel
surround or on the sunroof cassette according to the
marking.
aBond the sunroof mechanism using the special sup-
port (this operation requires two people).
aCentre the sunroof operating mechanism with in-
dexing guides with an operator inside the vehicle.
aCheck that the sunroof operating mechanism posi-
tioning shims make contact with the roof.
aRemove the two indexing guides 30 minutes after
bonding the sunroof operating mechanism.
III - FINAL OPERATION.
aConnect the sunroof computer connectors.
aRefit:
-the bolts (2) ,
-the sunroof console mounting,
-the bolts (1) ,
-the sunroof computer mounting,
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) ,
-the cross member mounting of the sunroof sun vi-
sor (see 52A, Non-side opening element mecha-
nisms, Sunroof sun visors: Removal - Refitting,
page 52A-15) ,
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the rear quarter panel trims (see Quarter panel
trim: Removal - Refitting) (MR 412, 71A, Body in-
ternal trim),
121715
WARNING
When cutting the cement bead, make sure that
the wire passes between the panel and the posi-
tioning shims on the edge of the sunroof opera-
ting mechanism.

52A-12
NON-SIDE OPENING ELEMENT MECHANISMS
Sunroof mobile panel guide: Removal - Refitting
PANORAMIC SUNROOF
52A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the sunroof mobile panel (see 52A, Non-
side opening element mechanisms, Sunroof mo-
bile panel: Removal - Refitting, page 52A-9) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the sunroof mobile panel guides using a
screwdriver at (1) then at (2) .aRemove the sunroof mobile panel guides at (3) and
(4) .
REFITTING
I - REFITTING PREPARATION OPERATION
a Note:
It is always necessary to replace the four mobile
panel guides at the same time.
138998
138994
138995
139287
Note:
Respect the position of the sunroof mobile panel
guides (A) and (B) .

54A-2
WINDOWS
Windscreen: Removal - Refitting
54A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aPosition the retaining shims and stops.
aPosition the seal (2) on the windscreen.
aFor preparation and bonding (see Technical Note
560A).
II - REFITTING OPERATION FOR PART
CONCERNED
aBond the windscreen (this operation requires two
people).
aRespect the following clearances and flush fitting:
- « Windscreen - Roof » ,
- « Windscreen - A-pillar » .
aHold the windscreen in position with masking tape.
III - FINAL OPERATION.
aReplace the rain and light sensor adhesive base
(depending on the equipment level) (see Rain and
light sensor: Removal - Refitting) (MR 411, 85A,
Wiping - Washing).
aConnect the rain and light sensor (depending on the
equipment level).
aRefit:
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the interior rear-view mirror (see 57A, Interior
equipment, Interior rear-view mirror: Removal -
Refitting, page 57A-14) ,
-the scuttle panel grille (see 56A, Exterior equip-
ment, Scuttle panel grille: Removal - Refitting,
page 56A-1) ,
-the lower windscreen trims (1) ,
-the windscreen wiper arms (see Windscreen wi-
per arm: Removal - Refitting) (MR 411, 85A, Wi-
pers - Washers).

54A-7
WINDOWS
Sunroof fixed window: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) .
aProtect:
-the sunroof's fixed window surround and the rear
section of the roof using masking tape,
-the inside of the vehicle.II - REMOVAL OPERATION FOR PART
CONCERNED
aCut the cement bead; this operation requires two
people.
aRemove the fixed window from the sunroof.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aPosition the new shims on the sunroof operating me-
chanism.
aFor preparation and bonding (see Technical Note
560A).
II - REFITTING OPERATION FOR PART
CONCERNED
aBond the sunroof fixed window using the specific
support (this operation requires two people):
-Support: PARV 202,
-set of arch supports: APARV 200 ESP. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121153

54A-8
WINDOWS
Sunroof fixed window: Removal - Refitting
54A
Respect the clearances and shut lines
aObserve the 6 mm clearance between the sunroof
fixed window (1) and the sunroof mobile panel (2) .
aThe sunroof's fixed window (1) should be slightly
lower than its mobile panel (2) .
aArrange the lateral clearances so that they are
equal.
III - FINAL OPERATION.
aRefit:
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
113525