rims RENAULT TWINGO RS 2009 2.G Mechanism And Accessories Workshop Manual

52A-6
NON-SIDE OPENING ELEMENT MECHANISMS
Sunroof operating mechanism: Removal - Refitting
52A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPartially open the sunroof mobile panel.
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the sunroof console (see Sunroof switch: Remo-
val - Refitting) (MR 411, 87D, Electric window win-
ders - Sunroof),
-the sun visors (see 57A, Interior equipment, Sun
visor: Removal - Refitting, page 57A-16) ,
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the rear bench seatback (depending on equipment
level) (see Rear bench seatback: Removal - Re-
fitting) (MR 412, 76A, Rear seat frames and run-
ners),
-the rear parcel shelf side trim panels (see Rear
parcel shelf side trim: Removal - Refitting) (MR
412, 71A, Body internal trim),-the rear panel trims (see Rear panel lining: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the B-pillar upper trims (see B-pillar upper trim:
Removal - Refitting) (MR 412, 71A, Body internal
trim),
-the rear quarter panel trims (see Quarter panel
trim: Removal - Refitting) (MR 412, 71A, Body in-
ternal trim),
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the cross member mounting of the sunroof sun vi-
sor (see 52A, Non-side opening element mecha-
nisms, Sunroof sun visors: Removal - Refitting,
page 52A-15) ,
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) .
aRemove:
-the bolts (1) ,
-the sunroof computer mounting.
aDisconnect the sunroof computer connectors. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121396

52A-7
NON-SIDE OPENING ELEMENT MECHANISMS
Sunroof operating mechanism: Removal - Refitting
52A
aRemove:
-the bolts (2) ,
-the sunroof console mounting.
aProtect the vehicle interior.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aProtect the sunroof frame using masking tape.
ainsert the threading needle preferably at the front left
or right of the sunroof operating mechanism.
aCut the cement bead (this operation requires two
people).
aRemove the sunroof operating mechanism using the
specific support (x2):
-Support: PARV 202,
-arch sets: APARV 200 ESP.
REFITTING
I - REFITTING PREPARATION OPERATION
aFor preparation and bonding see Technical Note
560A, General procedure for bonding windows
and sunroof.
aPosition:
-the two centring guides on the sunroof operating
mechanism,
-the positioning shims on the periphery of the sun-
roof operating mechanism.
II - REFITTING OPERATION FOR PART
CONCERNED
aPosition the cement bead at the interior roof panel
surround or on the sunroof cassette according to the
marking.
aBond the sunroof mechanism using the special sup-
port (this operation requires two people).
aCentre the sunroof operating mechanism with in-
dexing guides with an operator inside the vehicle.
aCheck that the sunroof operating mechanism posi-
tioning shims make contact with the roof.
aRemove the two indexing guides 30 minutes after
bonding the sunroof operating mechanism.
III - FINAL OPERATION.
aConnect the sunroof computer connectors.
aRefit:
-the bolts (2) ,
-the sunroof console mounting,
-the bolts (1) ,
-the sunroof computer mounting,
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) ,
-the cross member mounting of the sunroof sun vi-
sor (see 52A, Non-side opening element mecha-
nisms, Sunroof sun visors: Removal - Refitting,
page 52A-15) ,
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the rear quarter panel trims (see Quarter panel
trim: Removal - Refitting) (MR 412, 71A, Body in-
ternal trim),
121715
WARNING
When cutting the cement bead, make sure that
the wire passes between the panel and the posi-
tioning shims on the edge of the sunroof opera-
ting mechanism.

52A-8
NON-SIDE OPENING ELEMENT MECHANISMS
Sunroof operating mechanism: Removal - Refitting
52A
-the B-pillar upper trims (see B-pillar upper trim:
Removal - Refitting) (MR 412, 71A, Body internal
trim),
-the rear panel trims (see Rear panel lining: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the rear parcel shelf side trim panels (see Rear
parcel shelf side trim: Removal - Refitting) (MR
412, 71A, Body internal trim),
-the rear bench seatback (depending on equipment
level) (see Rear bench seatback: Removal - Re-
fitting) (MR 412, 76A, Rear seat frames and run-
ners),
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the sunroof console (see Sunroof switch: Remo-
val - Refitting) (MR 411, 87D, Electric window win-
ders - Sunroof),
-the sun visors (see 57A, Interior equipment, Sun
visor: Removal - Refitting, page 57A-16) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners).
aInitialise the sunroof motor (see Electric sunroof:
Initialisation) (MR 413, 87D, Electric windows - Su-
nroof).

54A-1
WINDOWS
Windscreen: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the windscreen wiper arms (see Winds-
creen wiper arm: Removal - Refitting) (MR 411,
85A, Washing - Wiping).
aRemove the lower trim pieces (1) from the winds-
creen.
aRemove:
-the scuttle panel grille (see 56A, Exterior equip-
ment, Scuttle panel grille: Removal - Refitting,
page 56A-1) ,
-the interior rear-view mirror (see 57A, Interior
equipment, Interior rear-view mirror: Removal -
Refitting, page 57A-14) ,
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim).
aDisconnect the rain and light sensor (depending on
the equipment level).II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the seal (2) from the windscreen.
aProtect the windscreen surround using masking ta-
pe.
aPosition the dashboard protector (Car. 1818).
a
aCut the cement bead. Special tooling required
Car. 1818Instr ument panel protector
Note:
Leave the rain sensor in place on the old winds-
creen during the replacement operation (depen-
ding on the equipment level).
119268
119271
108156
Note:
When cutting the cement bead, take care not to
cut the wiring harness.

54A-2
WINDOWS
Windscreen: Removal - Refitting
54A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aPosition the retaining shims and stops.
aPosition the seal (2) on the windscreen.
aFor preparation and bonding (see Technical Note
560A).
II - REFITTING OPERATION FOR PART
CONCERNED
aBond the windscreen (this operation requires two
people).
aRespect the following clearances and flush fitting:
- « Windscreen - Roof » ,
- « Windscreen - A-pillar » .
aHold the windscreen in position with masking tape.
III - FINAL OPERATION.
aReplace the rain and light sensor adhesive base
(depending on the equipment level) (see Rain and
light sensor: Removal - Refitting) (MR 411, 85A,
Wiping - Washing).
aConnect the rain and light sensor (depending on the
equipment level).
aRefit:
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the interior rear-view mirror (see 57A, Interior
equipment, Interior rear-view mirror: Removal -
Refitting, page 57A-14) ,
-the scuttle panel grille (see 56A, Exterior equip-
ment, Scuttle panel grille: Removal - Refitting,
page 56A-1) ,
-the lower windscreen trims (1) ,
-the windscreen wiper arms (see Windscreen wi-
per arm: Removal - Refitting) (MR 411, 85A, Wi-
pers - Washers).

56A-1
EXTERIOR EQUIPMENT
Scuttle panel grille: Removal - Refitting
56A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the wiper arms from the windscreen wiper
(see Windscreen wiper arm: Removal - Refitting)
(MR 411 Mechanical, 85A, Wiping - Washing).
aRemove the seal (1) .
aUnclip the windscreen lower trims (2) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the bolts (3) ,
-the clips (4) .
aRemove the scuttle panel grille (5) and (6) .
119268
119269
119270

56A-2
EXTERIOR EQUIPMENT
Scuttle panel grille: Removal - Refitting
56A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace:
-the clips under the scuttle panel grille,
-the foam strips which ensure the scuttle panel grille
sealing.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the scuttle panel grille,
-the clips (4) ,
-the bolts (3)
III - FINAL OPERATION.
aClip on the windscreen lower trims (2) .
aRefit:
-the seal (1) ,
-the windscreen wiper arms (see Windscreen wi-
per arm: Removal - Refitting) (MR 411 Mechani-
cal, 85A, Wiping - Washing).Note:
Check the condition and cleanliness of the
windscreen and scuttle panel grille before refit-
ting the scuttle panel grille.

57A-1
INTERIOR EQUIPMENT
Dashboard: Removal - Refitting
57A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove the passenger front airbag (see Passen-
ger's frontal airbag: Removal - Refitting) (88C,
Airbags and pretensioners).
aRemove:
-the windscreen pillar trims (see Windscreen pillar
trim: Removal - Refitting) (71A, Body internal
trim),
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and pre-
tensioners),
-the steering wheel (see Steering wheel: Removal
- Refitting) (36B, Power-assisted steering).aRemove the rev counter (depending on the equip-
ment level) (see Rev counter: Removal - Refitting)
(83A, Instrument panel).
aRemove:
-the steering column switch assembly (see Stee-
ring column switch assembly: Removal - Refit-
ting) (84A, Control - Signals),
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),
-the tweeters (see Tweeter: Removal - Refitting)
(86A, Radio),
-the centre console (see 57A, Interior equipment,
Centre console: Removal - Refitting, page 57A-
12) ,
-the centre front panel (see 57A, Interior equip-
ment, Centre front panel: Removal - Refitting,
page 57A-7) ,
-the control panel (see Control panel: Removal -
Refitting) (61A, Heating).
aUnclip the dashboard side faces. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
FRONT SIDE AIRBAG
ENGINE REV COUNTER
121136

57A-3
INTERIOR EQUIPMENT
Dashboard: Removal - Refitting
57A
aPartially remove the dashboard (this operation re-
quires two people).
aDetach the various wiring from the dashboard.
aRemove the dashboard (this operation requires two
people).
aNote the route of the cabling.
REFITTING
I - REFITTING PREPARATION OPERATION
aEnsure that the wiring is in good condition.
II - REFITTING OPERATION FOR PART
CONCERNED
aPartially refit the dashboard (this operation requires
two people).
aRefit:
-the various cable harnesses,
-the dashboard (this operation requires two people).
III - FINAL OPERATION.
aClip:
-the diagnostic socket (2) ,
-the access flap (1) .
aConnect the passenger airbag deactivation connec-
tor.
aClip on the dashboard side faces.
aRefit:
-the control panel (see Control panel: Removal -
Refitting) (61A, Heating),
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),-the tweeters (see Tweeter: Removal - Refitting)
(86A, Radio),
-the centre front panel (see 57A, Interior equip-
ment, Centre front panel: Removal - Refitting,
page 57A-7) ,
-the centre console (see 57A, Interior equipment,
Centre console: Removal - Refitting, page 57A-
12) ,
-the steering column switch assembly (see Stee-
ring column switch assembly: Removal - Refit-
ting) (84A, Control - Signals).
aRefit the rev counter (see Rev counter: Removal -
Refitting) (83A, Instrument panel).
aRefit:
-the steering wheel (see Steering wheel: Removal
- Refitting) (36B, Power-assisted steering),
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and pre-
tensioners),
-the windscreen pillar trims (see Windscreen pillar
trim: Removal - Refitting) (71A, Body internal
trim).
aRefit the passenger front airbag (see Passenger's
frontal airbag: Removal - Refitting) (88C, Airbags
and pretensioners).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aCarry out a function test on all functions.
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (88C, Airbags and pretensioners).
121157ENGINE REV COUNTER
FRONT SIDE AIRBAG
IMPORTANT
To avoid a fault with or even triggering of pyro-
technic components (airbags or pretensioners),
check the airbag computer using the diagnostic
tool.