sensor RENAULT TWINGO RS 2009 2.G Mechanism And Accessories Workshop Manual

54A-1
WINDOWS
Windscreen: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the windscreen wiper arms (see Winds-
creen wiper arm: Removal - Refitting) (MR 411,
85A, Washing - Wiping).
aRemove the lower trim pieces (1) from the winds-
creen.
aRemove:
-the scuttle panel grille (see 56A, Exterior equip-
ment, Scuttle panel grille: Removal - Refitting,
page 56A-1) ,
-the interior rear-view mirror (see 57A, Interior
equipment, Interior rear-view mirror: Removal -
Refitting, page 57A-14) ,
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim).
aDisconnect the rain and light sensor (depending on
the equipment level).II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the seal (2) from the windscreen.
aProtect the windscreen surround using masking ta-
pe.
aPosition the dashboard protector (Car. 1818).
a
aCut the cement bead. Special tooling required
Car. 1818Instr ument panel protector
Note:
Leave the rain sensor in place on the old winds-
creen during the replacement operation (depen-
ding on the equipment level).
119268
119271
108156
Note:
When cutting the cement bead, take care not to
cut the wiring harness.

54A-2
WINDOWS
Windscreen: Removal - Refitting
54A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aPosition the retaining shims and stops.
aPosition the seal (2) on the windscreen.
aFor preparation and bonding (see Technical Note
560A).
II - REFITTING OPERATION FOR PART
CONCERNED
aBond the windscreen (this operation requires two
people).
aRespect the following clearances and flush fitting:
- « Windscreen - Roof » ,
- « Windscreen - A-pillar » .
aHold the windscreen in position with masking tape.
III - FINAL OPERATION.
aReplace the rain and light sensor adhesive base
(depending on the equipment level) (see Rain and
light sensor: Removal - Refitting) (MR 411, 85A,
Wiping - Washing).
aConnect the rain and light sensor (depending on the
equipment level).
aRefit:
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the interior rear-view mirror (see 57A, Interior
equipment, Interior rear-view mirror: Removal -
Refitting, page 57A-14) ,
-the scuttle panel grille (see 56A, Exterior equip-
ment, Scuttle panel grille: Removal - Refitting,
page 56A-1) ,
-the lower windscreen trims (1) ,
-the windscreen wiper arms (see Windscreen wi-
per arm: Removal - Refitting) (MR 411, 85A, Wi-
pers - Washers).

55A-12
EXTERIOR PROTECTION
Rear bumper: Removal - Refitting
55A
aDisconnect the proximity sensor connector.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the proximity sensor connector.
aConnect the number plate light connector.
aRefit the rear bumper (this operation requires two
people).
II - FINAL OPERATION
aClip on the side extenders of the rear bumper in or-
der (7) , (8) , (9) , (10) , (11) .
aRefit the rear lights (see Rear wing light: Removal
- Refitting) (81A, Rear lighting).aCarry out a function test on all functions.
REAR PROXIMITY RADAR
REAR PROXIMITY RADAR
EQ UIPMENT LEVEL SPORT
132043

55A-14
EXTERIOR PROTECTION
Rear bumper: Conversion
55A
ADAPTATION
a
aDrill the rear bumper around the marking (1) using
an angular cutter or using the special tool (part no.:
77 11 419 232).
aFinish off using a small file.Note:
When a rear bumper is replaced, the replace-
ment part needs to be modified before it is pain-
ted so that the proximity sensors can be fitted.
120800

57A-15
INTERIOR EQUIPMENT
Interior rear-view mirror: Removal - Refitting
57A
aRemove interior rear-view mirror (5) .
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit interior rear-view mirror.
2nd type
aConnect the connector (4) .
aClip on:
-the lower cover (3) ,
-the upper cover (2) .
120794
Note:
When removing the interior rear-view mirror, be
careful not to damage the rain sensor nearby.