bonnet RENAULT TWIZY 2017 1.G Owners Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2017, Model line: TWIZY, Model: RENAULT TWIZY 2017 1.GPages: 118, PDF Size: 2.48 MB
Page 18 of 118
1.12
Important: before starting the vehi-
cle, please make sure that the cord
is properly stored in its housing and
that the flap is fully closed.
When charging, make sure that the
charging cord 2 is not overstretched.
Do not pull the vehicle using the
charging cord.
If the stretch limiter 8 is damaged,
please replace the charging cord.
Please contact an authorised dealer.
Precautions to take when removing
from the socket
– Unplug the cord from the power supply by pulling out the plug. The
instrument panel goes out;
– reposition the cord 2 correctly in the
front storage compartment.
Depending on the vehicle, place the
end of the plug in its housing or the
cord connector facing down;
– close the flap 3 . Check that the
bonnet is correctly locked.
ELECTRIC VEHICLE: charging (5/5)
3
2
Special conditions
If it becomes impossible to unplug the
vehicle from the charging terminal (the
plug is mechanically locked), turn the
key as if to start the vehicle, switch off
the ignition, then switch on again.
Attempting to start the vehicle ends the
charging process and unlocks the plug
from the terminal.
Repeat this operation as many times as
is necessary.8
2
After each charge, it is normal to
hear a fan noise from the vehicle if it
is still plugged in.
Page 66 of 118
4.2
Brake fluid level
The level control should be read with
the vehicle on level ground. This should
be checked frequently, and immedia-
tely if you notice even the slightest loss
in braking efficiency.
Accessing the brake fluid reservoir
Unclip the upper bar 2 of the bonnet
before moving your hand in 1.Topping up
After any operation on the hydraulic cir-
cuit, a specialist must replace the fluid.
Only use fluids approved by our
Technical Department (and taken from
a sealed container).
Replacement intervals
Refer to the Maintenance Document for
your vehicle.
Consult your approved dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
LEVELS (1/2)
Level 3
It is normal for the level to drop as
the linings become worn, but it should
never drop below the
MIN line.
If you wish to check the disc wear your-
self, you should obtain the document
explaining the checking procedure from
our network or from the manufacturer’s
website.
1
2
3
Page 80 of 118
5.6
Front lights
– Unclip upper bar 2 of the bonnet
before introducing your hand in 1;
– unscrew 3 the front lights using
standard tools;
– pull the headlight towards you as far as it will go.
Note: the headlight cannot be pulled
out completely. Avoid pulling too hard,
as this could damage the connections.
FRONT HEADLIGHTS: changing bulbs (1/2)
– Turn bulb a quarter of a turn 4;
– and/or undo the bulb 5, then turn the
bulb holder a quarter turn.
2
13
3
5
4
Type of bulbs
4 Side light
Bulb type: W5W.
5 Dipped beam/main beam head-
lights
Bulb type: H4.
The bulbs are under pres-
sure and can break when
replaced.
Risk of injury.
Page 90 of 118
5.16
TOWING, BREAKDOWN (3/3)
Access to the towing point
Remove:
– the bolts 4;
– the plastic clips 3;
– the clips 2 located under the front
bumper. Lift up the bonnet.
Only use the front and rear towing
points 4.
This towing point may only be used for
towing: never use it for lifting the vehi-
cle directly or indirectly.
Do not remove the key from
the ignition when the vehi-
cle is being towed.
4
Take care not to allow anything to
hit the 12 volt battery during towing.
2
4
3