brake light RENAULT TWIZY 2017 1.G Owners Manual

1.6
Special cases
– At very high exterior temperatures, a safety mode is triggered. Warning
light
 comes on the instrument
panel. This mode reduces vehicle
power and can lead to its immobi-
lisation. We recommend that you
stop and allow the electrical system
to cool down, until the warning light
 goes off. The vehicle then re-
covers its performance.
– After a maximum charge for the trac- tion battery and during the first few
miles when driving the vehicle, or
during very low outside tempera-
tures, the engine brake is tempora-
rily reduced. Please adapt your dri-
ving style accordingly.
The engine brake should
under no circumstances be
used as a substitute for the
brake pedal.
Bad weather, flooded roads:
Do not drive through
floods if the depth of
water is above the
lower edge of the wheel
rims.
If a water level reaches
the vehicle floor, do not re-
charge the vehicle. Please
consult an authorised
dealer.
Risk of electric shock and a risk to
life.
ELECTRIC VEHICLE: introduction (5/5)

1.15
ENGINE IMMOBILISER
This prevents the vehicle being
driven by anyone not in possession
of the vehicle’s coded ignition key.
The vehicle is automatically protected
after the engine is switched off.
Any unauthorised work
carried out on the engine
immobiliser (computers,
wiring, etc.) could be dan-
gerous. Work must be carried out
by qualified personnel.
Operating principle
When the engine is started, warning
light 1 remains lit for a few seconds,
then goes out (refer to the information
on “Starting, stopping the engine” in
Section 2).
If the code is not recognised, the warn-
ing light flashes rapidly and the vehicle
will not start. Vehicle protection tell-tale light
After the ignition has been switched off,
warning light
1 flashes and the vehicle
is protected.
Operating fault warning light
If the warning light continues to flash or
stays lit up permanently following an at-
tempt to start the engine, this indicates
a fault in the system.
In this case, use the second key (sup-
plied with the vehicle). If the fault is still
present, contact your authorised dealer,
as only they are qualified to repair the
engine immobiliser system.
1
When the engine immobiliser
system is activated, the handbrake
cannot be released.

1.31
DRIVING POSITION
7 and 12 door mirrorsTo adjust the mirrors, press on the
mirror.
8 Key ignition switch.
9 Handbrake.
10 Controls for: – forward gear,
– neutral,
– reverse.
11 Hazard warning lights switch.
5 – Windscreen wiper/washer stalk,
– On-board computer information
readout control,
– windscreen de-icer control.
6 Lockable storage.
1 Storage and accessories socket.
2 Stalk:
– horn,
– direction indicator lights,
– exterior lights,
– horn.
3 Instrument panel.
4 Location for driver’s airbag. The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
123456
891011127

1.33
WARNING LIGHTS (2/3)
®STOP light
This lights up when the ignition
is switched on and goes out as soon as
the engine is started. It lights up at the
same time as other warning lights, and
is accompanied by a beep.
It requires you to stop immediately, for
your own safety, as soon as traffic con-
ditions allow. Switch off the engine and
do not restart it.
Contact an approved Dealer.
Special feature: On steep slopes, a
warning light will come on and a beep
will sound if the vehicle is travelling
at excessive speed. You must then
reduce your speed. Risk of damage to
the engine. The warning light goes out
once the vehicle speed drops below the
maximum set level.
Windscreen de-icing warn-
ing light .
Ú12 V battery charge warning
light
If it comes on, limit the non-essential
use of any energy-consuming equip-
ment and accessories.
If it stays on, see an authorised dealer
as soon as possible.
If it comes on together with the warning
light
® and a beep, this indicates a
fault in the 12V battery charging circuit.
Stop as soon as traffic conditions allow
and contact an authorised dealer.
DHandbrake on and brake cir-
cuit incident warning light
This comes on when the ignition is
switched on and goes out as soon as
the handbrake is released.
If it comes on during braking and is ac-
companied by the
® warning light
and a beep, it indicates that the fluid
level in the circuit is low or that there is
a braking system fault.
Stop as soon as traffic conditions allow
and contact an approved Dealer.
The presence and operation of the warning lights DEPEND ON THE EQUIPMENT\
AND COUNTRY.
A
øWarning light
This lights up when the ignition
is switched on and goes out as soon as
the engine is started. It may comes on
in conjunction with other warning lights
on the instrument panel.
It means you should drive very care-
fully to an approved dealer as soon as
possible. If you fail to follow this recom-
mendation, you risk damaging your ve-
hicle.

2.2
“Accessories” position ANo power-consuming device will oper-
ate when the ignition is switched off.
“On” position MThe ignition is switched on:
Start position D
Starting the engine
Turn the key to the D position and hold
it in this position until you hear a beep.
Release the key.
As soon as warning light
Ṑ stops
flashing, your vehicle is ready to drive.“Stop, steering and
handbrake lock” position St
To unlock: turn the key and the steering
wheel slightly.
To lock: remove the key and turn the
steering wheel until the steering column
locks.
To release the handbrake, please see
the information on “Handbrake” in
Section 2.
STARTING, STOPPING THE ENGINE
The vehicle cannot be started if the
charging cord is plugged in and
powered or if the charging flap is
open.
Stopping the engine
Bring the key to “Stop” position.
Warning light
Ṑ goes out.
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-suffi-
cient alone on your vehicle, even for
a short time.
They may pose a risk of injury, such
as by starting the engine or activat-
ing equipment.
Risk of serious injury.

2.3
Driving
Press switch D, a beep will sound.
While driving, press the accelerator
pedal to achieve the desired speed.
Hill start
When setting off on a slope, release the
handbrake whilst pressing the brake
pedal before pressing the accelerator
pedal.
Reverse
Press switch R.
The reversing light will come on as
soon as reverse gear is selected (igni-
tion on).
A beep will sound.
GEAR CONTROL (1/2)
Display 1
The display 1 on the instrument panel
indicates the selection control posi-
tion 2.
Selection control 2
D: forward
N: neutral
R: reverse
Operation
– Switch on the ignition;
– start the engine;
– with your foot on the brake pedal,
release the handbrake (refer to the
information under “Handbrake” in
Section 2). It will now be possible to
drive off.
Only engage D or R when the vehicle
is at a standstill, with your foot on
the brake and the accelerator pedal
released.
To protect the charging cord, always
check that it is properly stored in its
housing before setting off.
The vehicle can only be started if
the charging cord is unplugged from
the vehicle and stored away.
1
D
N
R
2

2.4
Parking the vehicle
With the vehicle at a standstill, press
switch N.
Warning light 3 comes on the instru-
ment panel.
Engage the handbrake (please see the
“Handbrake” information in Section 2).
GEAR CONTROL (2/2)
In the event of an impact to the underside of the vehicle (e.g.: striki\
ng a
post, raised kerb or other street furniture), this may result in damage\
to
the vehicle (e.g.: twisted axle), the electrical circuit or the tracti\
on battery.
Do not touch the circuit elements or any fluids or liquids.
To prevent any risk of accident, have your vehicle checked by an authoris\
ed
dealer.
Risk of serious injury or electric shock.
N
3
NB: when the ignition is switched
off, the gear control automatically
switches to position N.
Temporary stop
At a standstill and with the engine run-
ning, when position D or R is engaged,
a beep will sound and warning light
Ṑ
flashes until one of the following condi-
tions is met:
– brake pedal pressed;
– accelerator pedal pressed;
– N switch pressed;
– the handbrake is secured.

2.5
Handbrake
To release:
With the ignition on:
– support on the brake pedal and maintain it sunk ;
– press 2 ;
– gently pull lever 1 towards you, keep-
ing the 2 button pressed down;
– push the lever down as far as it will go.When stationary and de-
pending on the slope and/or
vehicle load, it may be nec-
essary to pull up the hand-
brake at least two extra notches.
Make sure that the hand-
brake is properly released
when driving (red indicator
light off), otherwise over-
heating may occur.
1
2
HANDBRAKE
To apply:
Pull lever 1 upwards and make sure the
vehicle is immobilised. Warning light 3
D will come on on the instrument
panel.
3
Special conditions
It is not possible to release the hand-
brake when the 12 volt battery is dis-
charged.
You must recharge it (see “12V battery”
in Section 4) before you can release the
handbrake, or have the 12V battery re-
placed by an authorised dealer.
The handbrake is a vehicle safety
measure. It cannot be released
unless the ignition is switched on.

4.2
Brake fluid level
The level control should be read with
the vehicle on level ground. This should
be checked frequently, and immedia-
tely if you notice even the slightest loss
in braking efficiency.
Accessing the brake fluid reservoir
Unclip the upper bar 2 of the bonnet
before moving your hand in 1.Topping up
After any operation on the hydraulic cir-
cuit, a specialist must replace the fluid.
Only use fluids approved by our
Technical Department (and taken from
a sealed container).
Replacement intervals
Refer to the Maintenance Document for
your vehicle.
Consult your approved dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
LEVELS (1/2)
Level 3
It is normal for the level to drop as
the linings become worn, but it should
never drop below the
MIN line.
If you wish to check the disc wear your-
self, you should obtain the document
explaining the checking procedure from
our network or from the manufacturer’s
website.
1
2
3

5.8
Side light and brake light 2
Bulb type: P21/5W.
Reversing indicator light 3
Bulb type: PY21W.Reversing/side and brake
lights
From inside the vehicle:
– unclip covers 1 using a flat-blade
screwdriver or similar;
– unscrew using a Torx tool.
From outside the vehicle:
– release the light unit by pulling it backwards;
– unscrew bulb holder 2 or 3 and re-
place the bulb.
Note: ensure that the cable is in place
before inserting the light unit.
REAR LIGHTS: changing bulbs (1/2)
Refitting
To refit, proceed in the reverse order,
taking care not to damage the wiring.
The bulbs are under pres-
sure and can break when
replaced.
Risk of injury.
1
2
3