tow RENAULT TWIZY 2017 1.G Owners Manual

1.7
IMPORTANT RECOMMENDATIONS
Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, burns or elec-
tric shock and serious injury.
In the event of an accident or impact to the vehicle
In the event of an accident or an impact to the underside of the vehicle\
(e.g.: striking a post, raised kerb or other street fu rni-
ture), this may damage the electrical circuit or the traction battery.
Have the vehicle checked by an authorised dealer.
Never touch components or orange cables which are exposed and visible in\
side or outside the vehicle.
In the event of serious damage to the traction battery, leaks may occur:
– never touch the liquids (fluids, etc.) coming from the traction batter\
y;
– in the event of contact with the body, wash the affected area with plenty of water and consult a doctor as soon as possibl\
e.
In the event of fire
In the event of fire, make everyone evacuate the vehicle immediately and\
contact the emergency services, informing them that
this is an electric vehicle.
Only use extinguishing agents ABC or BC that are permitted for use with electrical fires. Do not use w\
ater or other extinguish-
ing agents.
In the event of damage to the electrical circuit, please call an authori\
sed dealer.
All towing operations
Please refer to the information on “Towing, breakdowns” in Section 5.
Washing the vehicle
Never wash the vehicle while it is charging.
Never wash the vehicle or the traction battery with a high-pressure jet.\
Do not wash the vehicle in a roller car wash.
This risks damaging the electric circuit.
Lifting
Using a lifting tool (jack, etc.) directly under the traction battery \
to lift the vehicle is prohibited. To replace a wheel, please go
to an authorised dealer.

1.16
FRONT SEAT
To move the seat forwards or
back
Lift handle 1 to unlock the seat. Release
the handle once the seat is in the cor-
rect position and ensure that the seat is
fully locked into position.
Access to the rear seats
Lift strap 2 and slide the driver’s seat
forwards.
To replace the seat in the driving posi-
tion, pull strap 2 towards the rear of the
vehicle until you get to the desired po-
sition.
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
2
1
Make sure the seat is
locked in place.
No object should be placed
on the floor: such objects
may slide under the pedals during
sudden braking manoeuvres and
obstruct their use.

1.35
DISPLAYS AND INDICATORS (1/2)
Charge level 1
The gauge indicates the level of energy
remaining.
NB: Each time you switch off the igni-
tion, the remaining energy level will be
calculated.
Once you switch on the ignition again,
you will see a slight change in the level
display. The presence and operation of the display and indicators DEPENDS ON THE \
LEVEL OF EQUIPMENT AND THE COUNTRY.
Immobilisation threshold imminent
When the battery reaches less than 6%
charge, a beep repeats every 20 sec-
onds and warning light
Ṏ flashes on
and off.
Motor performance gradually de-
creases until the vehicle comes to a
stop.
Please see the information on “Towing:
in the event of energy loss” in Section 5.
Charge meter 2
Please refer to the information on the
“Charge meter” in Section 2.
Speedometer 3
In kilometres or miles per hour.
1
2
3
Reserve level
When the battery reaches approxi-
mately 12% charge, warning light
Ṏ
comes on, along with a beep.
To optimise your range, please see the
information on “Recommendations:
saving energy” in Section 2.

1.38
AUDIBLE AND VISUAL SIGNALS
Horn
Press the end of stalk 1.
Headlight flasher
Pull stalk 1 towards you to flash the
headlights.
éHazard warning lights
Press switch 2 . This switch
lights up all four indicators simultane-
ously. It must only be used in an emer-
gency to warn drivers of other vehicles
that you have had to stop in an area
where stopping is prohibited or unex-
pected or that you are obliged to drive
under special conditions.
Direction indicators
Move stalk 1 parallel to the steering
wheel and in the direction you are going
to turn it.
When driving on the motorway, the
steering wheel is not often turned
enough to return the stalk automatically
to 0.
There is also an intermediate position
in which the switch may be held when
changing lanes.
When the stalk is released, it automati-
cally returns to 0.
21
0

1.40
áMain beam headlightsWith the stalk A in position
k, pull it towards you. An indicator
light on the instrument panel will come
on.
To return to the dipped headlights posi-
tion, pull stalk A towards you again.
eSwitching off the lightsReturn the stalk to its original
position. When the engine is started,
the dipped headlights stay on. They will
go out once the engine is switched off.
EXTERIOR LIGHTING AND SIGNALS (1/2)
Daytime running lights
The dipped headlights come on without
using the stalk A when the engine is
started.
uSide lights
Turn end 1 of stalk A until the
symbol is opposite mark 2.
The instrument panel lighting dims.
A
kDipped beam
headlights
Manual operation
Turn end 1 of stalk A until the symbol is
opposite mark 2.
With the ignition switched off, it is not
possible to operate the lights (to avoid
lights being used when parked).
21
A
When the vehicle is driven at
maximum permissible load (refer
to the information on «Weights» in
section 6), you must have the dipped
beam headlights adjusted, while it is
being used, by an Approved Dealer.

1.42
SCREEN WASHER/WIPER
nWindscreen wiper
With the ignition on, move
stalk 1:
A park
B intermittent wiping The wipers will pause for several
seconds between sweeps.
C normal wiping speed
D fast wiping speed
A
B
C
D
1
1
Windscreen washer
With the ignition on, pull stalk 1 towards
you.
In the snow or ice, make sure that
the wiper blades are not stuck by
ice.
Keep an eye on the condition of the
blade. Replace the wiper blades
as soon as they begin to lose effi-
ciency: approximately once a year.
Check the condition of the wiper
blades. How long they last depends
on you:
– they should be kept clean: clean the blades and the windscreen
regularly with soapy water;
– do not use them when the wind- screen is dry;
– free them from the windscreen when they have not been used
for a long time.
In any event, replace them as soon
as they begin to lose efficiency: ap-
proximately once a year.
When working on the vehi-
cle, ensure that the wind-
screen wiper stalk is in po-
sition A (off).
Risk of injury.
Before any action involving
the windscreen (washing
the vehicle, de-icing, clean-
ing the windscreen, etc.)
return stalk 1 to position A (park).
Risk of injury and/or damage.

2.5
Handbrake
To release:
With the ignition on:
– support on the brake pedal and maintain it sunk ;
– press 2 ;
– gently pull lever 1 towards you, keep-
ing the 2 button pressed down;
– push the lever down as far as it will go.When stationary and de-
pending on the slope and/or
vehicle load, it may be nec-
essary to pull up the hand-
brake at least two extra notches.
Make sure that the hand-
brake is properly released
when driving (red indicator
light off), otherwise over-
heating may occur.
1
2
HANDBRAKE
To apply:
Pull lever 1 upwards and make sure the
vehicle is immobilised. Warning light 3
D will come on on the instrument
panel.
3
Special conditions
It is not possible to release the hand-
brake when the 12 volt battery is dis-
charged.
You must recharge it (see “12V battery”
in Section 4) before you can release the
handbrake, or have the 12V battery re-
placed by an authorised dealer.
The handbrake is a vehicle safety
measure. It cannot be released
unless the ignition is switched on.

2.8
ENVIRONMENT
Please make your own
contribution towards
protecting the environment
too.
– Worn parts replaced in the course of routine vehicle maintenance (vehi-
cle battery, etc.) must be disposed of
through specialist bodies.
– At the end of the vehicle’s service life, it should be sent to approved
centres to ensure that it is recycled.
– In all cases, comply with local legis- lation.
Recycling
Your vehicle is 85% recyclable and
95% recoverable.
To achieve these objectives, many of
the vehicle components have been de-
signed to enable them to be recycled.
The materials and structures have
been carefully designed to allow these
components to be easily removed and
reprocessed by specialist companies.
In order to preserve raw material re-
sources, this vehicle incorporates nu-
merous parts made from recycled plas-
tics or renewable materials (vegetable
or animal-derived materials such as
cotton or wool).
Your vehicle has been designed with
respect for the environment in mind for
its entire service life: during production,
use and at the end of its life.
Manufacture
Your vehicle has been manufactured at
an industrial site which uses a progress
policy to reduce environmental impacts
on rivers and natural areas (reduc-
tion of water and energy consumption,
visual and noise pollution, atmospheric
emissions and waste water, sorting and
reusing waste).

3.4
PASSENGER COMPARTMENT STORAGE/FITTINGS (2/4)
Ensure that no hard, heavy
or pointed objects are
placed in the “open” storage
compartments in such a
way that they may fall onto passen-
gers during sudden turning, braking
or in the event of an accident.
Rear storage space 10
To unlock the seat cushion B and the
seatback A, insert the ignition key in
lock 7 and turn it. Unclip the seatback
A, then slide it
back and pull towards you.
Move the seat cushion B in 8, then pull
upwards to unclip the base.
Push the seat cushion B and lift it
(movement C) to take it out from the
runners 9.
Note: when replacing, make sure you
lock the cushion and the seat back in
place.
The closure 7 enables the seat back
and cushion of the rear passenger
seat and the rear storage compart-
ment to be locked or unlocked.
B
8
A
10
Do not place an object or
pet on the storage space if
it has not first been secured
using a specific accessory
for the vehicle.
Risk of serious injury when braking
sharply or in an impact.
9
7
C

3.5
PASSENGER COMPARTMENT STORAGE/FITTINGS (3/4)
Rear storage space
The rear seat can be transformed into a
storage space.
– To unlock the seat cushion B and the
seatback A, insert the ignition key in
lock 7 and turn it;
– unclip the seatback A, then slide it
downwards and pull towards you;
Ensure that no hard, heavy
or pointed objects are
placed in the “open” storage
compartments in such a
way that they may fall onto passen-
gers during sudden turning, braking
or in the event of an accident.
– move the seat cushion B in 8 , then
pull it upwards to unclip the base;
– push the seat cushion B and lift it
(movement C) to take it out from the
runners 9;
– depending on the vehicle, insert the blanking cover 11 into the seatbelt
housing. On vehicles fitted with it,
the blanking cover 11 is located on
the back of seatback A;
11
B
8
A
9
7
C