sensor SAAB 9-2X 2006 Owners Manual

Seat, seatbelt and SRS airbags
1-19
1
– CONTINUED –
Front seatbelt pretensionersThe driver’s and front passenger’s seat-
belts have a seatbelt pretensioner. The
seatbelt pretensioners are designed to be
activated in the event of an accident in-
volving a moderate to severe frontal colli-
sion.
The pretensioner sensor also serves as
the frontal SRS airbag sensor. If the sen-
sor detects a certain predetermined
amount of force during a frontal collision,
the front seatbelt is quickly drawn back in
by the retractor to take up the slack so that
the belt more effectively restrains the front
seat occupant.
When a seatbelt pretensioner is activated,
an operating noise will be heard and a
small amount of smoke will be released.These occurrences are normal and not
harmful. This smoke does not indicate a
fire in the vehicle.
Once the seatbelt pretensioner has been
activated, the seatbelt retractor remains
locked. Consequently, the seatbelt can
not be pulled out and retracted and there-
fore must be replaced.
NOTE
Seatbelt pretensioners are not de-
signed to activate in minor frontal im-
pacts, in side or rear impacts or in roll-
over accidents.

The driver’s seat and passenger’s
seat pretensioners and frontal SRS air-
bag operate simultaneously.

Pretensioners are designed to func-
tion on a one-time-only basis. In the
event that a pretensioner is activated,
both the driver’s and front passenger’s
seatbelt retractor assemblies must be
replaced only by an authorized Saab
dealer. When replacing seatbelt retrac-
tor assemblies, use only genuine Saab
parts.

If either front seatbelt does not re-
tract or cannot be pulled out due to a
malfunction or activation of the preten-
sioner, contact your Saab dealer as
soon as possible.

If the front seatbelt retractor assem-bly or surrounding area has been dam-
aged, contact your Saab dealer as
soon as possible.

When you sell your vehicle, we urge
you to explain to the buyer that it has
seatbelt pretensioners by alerting him
to the contents of this section.
100121

To obtain maximum protection,
the occupants should sit in an up-
right position with their seatbelts
properly fastened. Refer to the
“Seatbelts” section in this chap-
ter.

Do not modify, remove or strike
the front seatbelt retractor assem-
blies or surrounding area. This
could result in accidental activa-
tion of the seatbelt pretensioners
or could make the system inoper-
ative, possibly resulting in seri-
ous injury. Seatbelt pretensioners
have no user-serviceable parts.
For required servicing of front
seatbelt retractors equipped with
seatbelt pretensioners, see your
nearest Saab dealer.
A1910BE-A-GSAAB.book Page 19 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

1-20
Seat, seatbelt and SRS airbags

System monitorsA diagnostic system continually monitors
the readiness of the seatbelt pretensioner
while the vehicle is being driven. The seat-
belt pretensioners share the control mod-
ule with the SRS airbag system. There-
fore, if any malfunction occurs in a seat-
belt pretensioner, the SRS airbag system
warning light will illuminate. The SRS air-
bag system warning light will show normal
system operation by lighting for approxi-
mately
6 seconds when the ignition switch
is turned to the “ON” position.The following components are monitored
by the indicator:

Front sub sensor (Right-hand side)

Front sub sensor (Left-hand side)

Airbag control module (including impact
sensors)

Frontal airbag module (Driver’s side)

Frontal airbag module (Front passen-
ger’s side)

Side airbag sensor (Center pillar right-
hand side)

Side airbag sensor (Center pillar left-
hand side)

Side airbag module (Driver’s side)

Side airbag module (Front passenger’s
side)

Seatbelt pretensioner (Driver’s side)

Seatbelt pretensioner (Front passen-
ger’s side)

Seatbelt buckle switch (Driver’s side)

Seatbelt buckle switch (Front passen-
ger’s side)

Driver’s seat position sensor

Front passenger’s seatbelt tension sen-
sor

Front passenger’s occupant detection
system weight sensor

Front passenger’s occupant detection
control module

Front passenger’s frontal airbag ON
and OFF indicator

All related wiring

When discarding front seatbelt re-
tractor assemblies or scrapping
the entire vehicle due to collision
damage or for other reasons, con-
sult your Saab dealer.
100291
If the warning light exhibits any of
the following conditions, there may
be a malfunction in the seatbelt pre-
tensioners and/or SRS airbag sys-
tem. Immediately take your vehicle
to your nearest Saab dealer to have
the system checked. Unless
checked and properly repaired, the
seatbelt pretensioners and/or SRS
airbag will not operate properly in
the event of a collision, which may
increase the risk of injury.

Flashing or flickering of the warn-
ing light

No illumination of the warning
light when the ignition switch is
first turned to the “ON” position

Continuous illumination of the
warning light

Illumination of the warning light
while driving
A1910BE-A-GSAAB.book Page 20 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Seat, seatbelt and SRS airbags
1-21
1
– CONTINUED –

System servicing
NOTEIf the front part of the vehicle is dam-
aged in an accident to the extent that
the seatbelt pretensioner does not op-
erate, contact your Saab dealer as
soon as possible.
Precautions against vehicle
modificationAlways consult your Saab dealer if you
want to install any accessory parts to your
vehicle.

When discarding a seatbelt retrac-
tor assembly or scrapping the en-
tire vehicle damaged by a colli-
sion, consult your Saab dealer.

Tampering with or disconnecting
the system’s wiring could result in
accidental activation of the seat-
belt pretensioner and/or SRS air-
bag or could make the system in-
operative, which may result in se-
rious injury. The wiring harnesses
of the seatbelt pretensioner and
SRS airbag systems are covered
with yellow insulation and the
connectors of the system are yel-
low for easy identification. Do not
use electrical test equipment on
any circuit related to the seatbelt
pretensioner and SRS airbag sys-
tems. For required servicing of
the seatbelt pretensioner, see
your nearest Saab dealer.
The front sub sensors are located in
both front fenders and the SRS air-
bag control module including the
impact sensors is located under the
center console. If you need service
or repair in those areas or near the
front seatbelt retractors, we recom-
mend that you have an authorized
Saab dealer perform the work.
Do not perform any of the following
modifications. Such modifications
can interfere with proper operation
of the seatbelt pretensioners.

Attachment of any equipment
(bush bar, winches, snow plow,
skid plate, etc.) other than genu-
ine Saab accessory parts to the
front end.

Modification of the suspension
system or front end structure.

Installation of a tire of different
size and construction from the
tires specified on the vehicle label
attached to the door pillar or spec-
ified for individual vehicle models
in this Owner’s Manual.
A1910BE-A-GSAAB.book Page 21 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

1-36
Seat, seatbelt and SRS airbags
1 2
3 4
5 6
1415
20
19
8
1117
18
9
710
12
16 13
100701
1) Airbag control module (including im-
pact sensors)
2) Frontal airbag module (driver’s
side)
3) Frontal airbag module (front pas-
senger’s side)
4) Front sub sensor (left-hand side)
5) Front sub sensor (right-hand side)
6) Side airbag module (driver’s side)
7) Side airbag module (front passen-
ger’s side)
8) Side airbag sensor (center pillar left-
hand side)
9) Side airbag sensor (center pillar
right-hand side)
10)Airbag wiring (yellow)
11)Seatbelt pretensioner (driver’s side)
12)Seatbelt pretensioner (front pas-
senger’s side)
13)Seatbelt buckle switch (front pas-
senger’s side)
14)Seatbelt buckle switch (driver’s
side)
15)Driver’s seat position sensor
16)Front passenger’s seatbelt tension
sensor
17)Front passenger’s occupant detec-
tion system weight sensor
18)Front passenger’s occupant detec-
tion control module
19)Front passenger’s frontal airbag
ON and OFF indicator
20)SRS airbag system warning light
A1910BE-A-GSAAB.book Page 36 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Seat, seatbelt and SRS airbags
1-39
1
– CONTINUED –


Driver’s SRS frontal airbag
The driver’s SRS frontal airbag uses a
dual stage inflator. The inflator operates in
different ways depending on the severity
of impact, backward-forward adjustment
of the driver’s seat position and whether or
not he/she is wearing the seatbelt.
The backward-forward adjustment of the
driver’s seat position is monitored by thedriver’s seat position sensor under the
driver’s seat.
Whether or not the driver is wearing the
seatbelt is monitored by the seatbelt buck-
le switch.
Observe the following precautions. Failure
to do so may cause the seatbelt buckle
switch and/or the seat position sensor to
malfunction, preventing the Saab ad-
vanced frontal airbag system from func-
tioning correctly or causing the system to
fail.

Do not place articles/metal objects or in-
stall any accessory other than a genuine
Saab accessory under the driver’s seat.
Do not allow the rear seat occupant to kick
the driver’s seat or push up its bottom sur-
face with his/her feet.

Do not place a magnet near the seatbelt
buckle or under the driver’s seat.
If the seatbelt buckle switch and/or the
driver’s seat position sensor have failed,
the SRS airbag system warning light will il-
luminate. Although the driver’s SRS fron-
tal airbag can deploy regardless of the
backward-forward adjustment of the driv-
er’s seat position even when the warning
light is on, have the system inspected by
your Saab dealer immediately if the SRS
airbag system warning light comes on.
NOTEThe driver’s SRS side airbag and seat-
belt pretensioner are not controlled by
the Saab advanced frontal airbag sys-
tem.

Front passenger’s SRS frontal air-
bag
The front passenger’s SRS frontal airbag
uses a dual stage inflator. The inflator op-
erates in different ways depending on the
severity of impact.
The total load on the seat is monitored by
the occupant detection system’s weight
sensor located under the seat.
The system has another sensor that mon-
itors the tension of the front passenger
seatbelt. Using the total seat load and
seatbelt tension data from the sensors,
the occupant detection system deter-
mines whether the front passenger’s SRS
frontal airbag should or should not be in-
flated.
The occupant detection system may not
inflate the front passenger’s SRS frontal
airbag even when the driver’s SRS frontal
airbag deploys. This is normal.
Observe the following precautions. Failure
to do so may prevent the Saab advanced
frontal airbag system from functioning cor-
rectly or cause the system to fail.

Do not apply any strong impact to the Do not attach accessories to the
windshield, or fit an extra-wide mir-
ror over the rear view mirror. If the
SRS airbag deploys, those objects
could become projectiles that could
seriously injure vehicle occupants.
100157
A1910BE-A-GSAAB.book Page 39 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

1-44
Seat, seatbelt and SRS airbags

OperationA) Driver’s side
B) Passenger’s side
1) SRS AIRBAGs deploy as soon as a collision occurs.
2) After deployment, SRS AIRBAGs start to deflate immediately so that the driver’s vision is not
obstructed.
A
B
1
2
100619
The SRS airbag can function only when
the ignition switch is in the “ON” position.
The Saab advanced frontal airbag system
is designed to determine the activation or
deactivation condition of the front passen-
ger’s SRS frontal airbag depending on the
total load on the front passenger’s seat
monitored by the front passenger’s occu-
pant detection system weight sensor. For
this reason, only the driver’s SRS frontal
airbag may deploy in the event of a colli-
sion, but this does not mean failure of the
system.
If the front sub sensors inside both front
fenders and the impact sensors in the air-
bag control module detect a predeter-
mined amount of force during a frontal col-
lision, the control module sends signals to
the airbag module(s) (only driver’s module
or both driver’s and front passenger’s
modules) instructing the module(s) to in-
flate the SRS frontal airbag(s). The driv-
er’s and front passenger’s SRS frontal air-
bags use dual stage inflators. The two in-
flators of each airbag are triggered either
sequentially or simultaneously, depending
on the severity of impact, backward-for-
ward adjustment of the driver’s seat posi-
tion and fastening/unfastening of the seat-
belt in the case of the driver’s SRS frontal
airbag and depending on the severity of
impact and the total load on the seat in the
A1910BE-A-GSAAB.book Page 44 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

1-50
Seat, seatbelt and SRS airbags

Operation1) SRS side airbag deploys as soon as a
collision occurs.
2) SRS side airbag protects the front pas-
senger’s head and chest.
3) After deployment, SRS side airbag
starts to deflate immediately.
The SRS side airbag is designed to func-
tion only when the ignition switch is in the
“ON” position.
The driver’s and front passenger’s SRS
side airbags deploy independently of each
other since each has its own impact sen-
sor. Also, the SRS side airbag deploys in-
dependently of the frontal airbags in the
steering wheel and instrument panel.
An impact sensor is incorporated into
each of the vehicle’s center pillars. If ei-
ther sensor detects a certain predeter-
mined amount of force during a side im-
pact collision, the control module sends a
signal to the side airbag module on the im-
pacted side of the vehicle, instructing it to
inflate the SRS side airbag. Then the side
airbag module produces gas, which in-
stantly inflates the SRS side airbag. After
deployment, the SRS side airbag will de-
flate in a few seconds.
The SRS side airbag deploys even when
no one occupies the seat on the side on
which an impact is applied.
When the SRS side airbag deploys, a sud-
den, fairly loud inflation noise will be heard
and some smoke will be released. These
occurrences are normal result of the de-
ployment. This smoke does not indicate a
fire in the vehicle. Do not put any kind of cover or
clothes or other objects over either
front seatback and do not attach la-
bels or stickers to the front seat sur-
face on or near the SRS side airbag.
They could prevent proper deploy-
ment of the SRS side airbag, reduc-
ing protection available to the front
seat’s occupant.
1
2
3
100625
A1910BE-A-GSAAB.book Page 50 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Seat, seatbelt and SRS airbags
1-53
1
– CONTINUED –

Examples of the types of accidents in which the SRS side airbag will ba-
sically not deploy.1) The vehicle is involved in a frontal colli-
sion with another vehicle (moving or sta-
tionary).
2) The vehicle is struck from behind.
The SRS side airbag is basically not de-
signed to deploy if the vehicle is involved
in a frontal collision or is struck from be-
hind. Examples of such accidents are il-
lustrated.1) First impact
2) Second impactIn an accident where the vehicle is struck
from the side more than once, the SRS
side airbag deploys only once.
Example: In the case of a double side im-
pact collision, first with one vehicle and
immediately followed by another from the
same direction, once the SRS side airbag
is activated on the first impact, it will not be
activated on the second.

SRS airbag system monitorsA diagnostic system continually monitors
the readiness of the SRS airbag system
(including front seatbelt pretensioners)
while the vehicle is being driven. The SRS
airbag system warning light “AIRBAG” will
show normal system operation by lighting
for approximately 6 seconds when the ig-
nition switch is turned to the “ON” position.
The following components are monitored
by the indicator:

Front sub sensor (Right-hand side)

Front sub sensor (Left-hand side)

Airbag control module (including impact
sensors)

Frontal airbag module (Driver’s side)

Frontal airbag module (Front passen-
ger’s side)
1
2
100716
2
1
100629
100291
A1910BE-A-GSAAB.book Page 53 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

1-54
Seat, seatbelt and SRS airbags

Side airbag sensor (Center pillar right-
hand side)

Side airbag sensor (Center pillar left-
hand side)

Side airbag module (Driver’s side)

Side airbag module (Front passenger’s
side)

Seatbelt pretensioner (Driver’s side)

Seatbelt pretensioner (Front passen-
ger’s side)

Seatbelt buckle switch (Driver’s side)

Seatbelt buckle switch (Front passen-
ger’s side)

Driver’s seat position sensor

Front passenger’s seatbelt tension sen-
sor

Front passenger’s occupant detection
system weight sensor

Front passenger’s occupant detection
control module

Front passenger’s frontal airbag ON
and OFF indicator

All related wiring

SRS airbag system servicing
If the warning light exhibits any of
the following conditions, there may
be a malfunction in the seatbelt pre-
tensioners and/or SRS airbag sys-
tem. Immediately take your vehicle
to your nearest Saab dealer to have
the system checked. Unless
checked and properly repaired, the
seatbelt pretensioners and/or SRS
airbag will not operate properly in
the event of a collision, which may
increase the risk of injury.

Flashing or flickering of the warn-
ing light

No illumination of the warning
light when the ignition switch is
first turned to the “ON” position

Continuous illumination of the
warning light

Illumination of the warning light
while driving

When discarding an airbag mod-
ule or scrapping the entire vehicle
damaged by a collision, consult
your Saab dealer.

The SRS airbag has no user-ser-
viceable parts. Do not use electri-
cal test equipment on any circuit
related to the SRS airbag system.
For required servicing of the SRS
airbag, see your nearest Saab
dealer. Tampering with or discon-
necting the system’s wiring could
result in accidental inflation of the
SRS airbag or could make the sys-
tem inoperative, which may result
in serious injury. The wiring har-
nesses of the SRS airbag system
are covered with yellow insulation
and system connectors are yellow
for easy identification.
A1910BE-A-GSAAB.book Page 54 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Seat, seatbelt and SRS airbags
1-55
1
– CONTINUED –
In the event that the SRS airbag is de-
ployed, replacement of the system
should be performed only by an autho-
rized Saab dealer. When the compo-
nents of the SRS airbag system are re-
placed, use only genuine Saab parts.
To ensure their long-term reliability, the
SRS airbags must be inspected by a Saab
dealer ten years after the date of manu-
facture, which is shown on the certification
plate attached to the driver’s door jamb.
NOTEIn the following cases, contact your
Saab dealer as soon as possible.

The front part of the vehicle was in-
volved in an accident in which only the
driver’s SRS frontal airbag or both driv-
er’s and front passenger’s SRS frontal
airbags did not deploy.

The pad section of the steering
wheel or front passenger’s frontal air-
bag cover is scratched, cracked, or
otherwise damaged.
In addition, if your vehicle is equipped
with SRS side airbags, contact your
Saab dealer as soon as possible in the
following cases.

Either center pillar or a nearby area
of the vehicle was involved in an acci-
dent in which the SRS side airbag did
not deploy.

The fabric or leather of either front
seatback is cut, frayed, or otherwise
damaged.

Precautions against vehicle
modification
If you need service or repair in areas
listed in the following, have an au-
thorized Saab dealer perform the
work. The SRS airbag control mod-
ule, impact sensors and airbag mod-
ules are stored in these areas.

Under the center console

Inside each front fender

Steering wheel and column and
nearby areas

Top of the dashboard on front
passenger’s side and nearby ar-
eas

Each front seat and nearby area

Inside each center pillar

To avoid accidental activation of
the system or rendering the sys-
tem inoperative, which may result
in serious injury, no modifications
should be made to any compo-
nents or wiring of the SRS airbag
system.
This includes following modifica-
tions:

Installation of custom steering
wheels

Attachment of additional trim
materials to the dashboard

Installation of custom seats

Replacement of seat fabric or
leather

Installation of additional fabric
or leather on the front seat
A1910BE-A-GSAAB.book Page 55 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com