headlights SAAB 9-3 2006 User Guide

252 Car careFuse panel in engine bayNo. Amp. Function
1--
210 Engine control module; automatic transmission con-
trol module3
320Horn
4 10 Engine control module; battery disconnect switch3
5--
610 Selector lever, automatic transmission3; clutch pedal
switch
7--
8 5 Relay for vacuumpump (brake system)3
9--
10 - -
11 - -
12 10 Washer fluid pump, rear window3
13 - -
14 - -
15 30 Washer fluid pump, headlights3
1630 Front right parking light; front right turn signal; left and
right side turn signal; right high beam; left low beam;
front left fog light3
17 30 Windshield wiper motor, low speed
18 30 Windshield wiper motor, high speed
19 20 Parking heater; auxiliary heater3
20 10 Headlight levelling3
21 - -
22 30 Washer fluid pump, windshield
23 - -
24 20 Flash-to-pass
25 20 Amplifier, sound system II3
2630 Front left turn signal; front left parking light; front right
fog light3; right low beam; left high beam
27
–37MAXI
93U S M 06.book Page 252 Friday, February 18, 2005 1:15 PM
ProCarManuals.com

253 Car care
Fuse panel in front of battery3
Relays
R 1 Washer fluid pump, windshield
R2 -
R3 -
R4 -
R 5 Flash-to-pass
R6 Horn
R7 -
R8 Starter motor
R 9 Windshield wipers ON/OFF
R10 Washer fluid pump, rear window3
R11 Ignition +15
R12 Windshield wipers, high/low speed
R13 -
R14 Washer fluid pump, headlights3
R15 -
R16 -
No. Amp. Function
1 - Air pump, secondary air3
220 Fuel pump; preheated oxygen sensors (lambda
probe)
310A/C compressor
430Main relay
Relays
1-
2 A/C-compressor
3 Preheated oxygen sensors (lambda probe)
4 Main relay, engine (ECM/EVAP/injectors)
93U S M 06.book Page 253 Friday, February 18, 2005 1:15 PM
ProCarManuals.com

277 Car care
Cleaning and caring for leather
upholsteryThe principal reason for treating leather
upholstery is to maintain its elegant appear-
ance and to provide it with a protective film.
Disco lour at ion caused by dust and wear
mainly affects the lighter shades, although
this is not detrimental to the leather, indeed,
the patina resulting from use is often consid-
ered desirable in leather. But if the leather is
allowed to become too grubby, it can start to
look shabby.
The leather upholstery should be cleaned
and reconditioned twice a year in conjunc-
tion with spring and autumn inspections. In
very warm, dry climates the leather may
need more regular reconditioning. Use con-
ventional leather care products. Follow the
instructions on the packaging.
Do not use unknown harsh polishing
agents, cleaning agents, sprays, coarse
soap or hot water.
Textile carpetingTextile carpeting should be vacuum
cleaned regularly. Carpeting can also be
cleaned using a brush or sponge and carpet
shampoo.
For safety reasons, vacuum cleaners that
are not earthed (grounded) must not be
used out of doors.Engine bayThe engine bay should be cleaned with an
engine decreasing and rinsed with hot
water. The headlights must be covered
over. Do not use a pressure washer. Avoid
spraying electrical components and con-
nectors.
Do not use petrol as a cleaning agent or sol-
vent when carrying out repairs or mainte-
nance. Saab recommends the use of envi-
ronmentally-friendly decrescendos.
WashingThe bodywork must be washed frequently.
When the car is new, the body should be
washed by hand using plain cold water and
a clean, soft brush through which the water
flows. Automatic caresses should be
avoided when the car is new.
After 5–6 months the paintwork will have
hardened. To facilitate cleaning, a suitable
detergent can be added to the water, which
should be lukewarm.
Remove any bird droppings without delay,
as these can discolor the paintwork and
prove difficult to polish out. Lay a wad of wet
paper on the patch of dirt and leave it for a
minute or so. It will then be easy to wash off
the dirt.
Use a soft cloth moistened with white spirit
to remove splashes of tar or asphalt. Do not
use strong cleaners, as these can dry out
the paintwork.
The underside of the car also needs wash-
ing regularly, and this should be done extra NOTICEDo not use alcohol-based cleaners on the
plastic lenses of the front or rear lights, as
these can cause a crackling effect on the
lenses.
The door mirrors should be folded in
before the car enters an automatic car
wash.
93U S M 06.book Page 277 Friday, February 18, 2005 1:15 PM
ProCarManuals.com

283 Car care
Maintenance The compressor drive belt should be
inspected under the regular service
program.
 Clean away dirt and insects from the
condenser and radiator to prevent clog-
ging. When washing the car, use the hose
to spray the radiator and condenser
(located in front of the radiator) from both
sides (both from the front of the car and
from inside the engine bay). Do not use a
pressure washer.
Caution: Do not hose down the radia-
tor and condenser while the engine is
hot.Other than in extremely cold weather, do not
screen the radiator, e.g. with netting, as this
will greatly diminish its cooling capacity.
 Applicable to the manual climate control
system - During cold months the air condi-
tioning should be switched on once or
twice a month and run for 5–10 minutes
during highway driving once the engine is
warm.
This action saves the gaskets in the
compressor from being spoiled. The
compressor uses a lubricant that circu-
lates with the coolant.
Note:
The A/C system cannot be switched on
when the outside temperature is below 32°F
(0°C). Turn on the A/C system when the car
is standing in a warm place. Simplest is to
always have the A/C button pressed in. The
A/C system will then cut in automatically
when the outside temperature is high
enough.
Headlight aimingThe vehicle has a visual optical headlight
aiming system equipped with vertical
aiming device. The aim has been preset at
the factory and should normally not need
further adjustments.
If your headlights are damaged in a crash,
the headlight aim may be affected. If you
believe your headlights need to be re-
aimed, we recommend that you take it to
your Saab dealer for service. However, it is
possible for you to re-aim your headlights as
described in the following procedure.
NOTICEDo not use a pressure washer when
cleaning the condenser or radiator due to
the risk of damage.
WARNING
Before checking/adjusting the headlight
aiming, switch off the engine to avoid
danger of fingers and hands being injured
by moving parts.
The radiator fan can start up even when
the engine is switched off.NOTICETo make sure that your headlights are
aimed properly read all instructions
before beginning. Failure to follow these
instructions could cause damage to
headlight parts or a not correctly aimed
headlight.
93U S M 06.book Page 283 Friday, February 18, 2005 1:15 PM
ProCarManuals.com

284 Car careTo check the aim, the vehicle should be
properly prepared as follows:
 The vehicle shall be placed so that the
headlights are 25 ft (7.6 m) from a light
colored wall or other flat surface. The
aiming area should be darkened, this will
improve your ability to see the beam of the
low beam headlight being aimed.
An optical headlamp aimer can also be
used and will than replace the wall.
 The vehicle must have all four wheels on
a perfectly level surface which is level all
the way to the wall or other flat surface.
 The vehicle should be placed so it is per-
pendicular to the wall or other flat surface. The vehicle should be unloaded and fuel
tank full, and one person or 160 lbs.
(75 kg) on the drivers seat.
 The vehicle should be fully assembled
and all other work stopped while headlight
aiming is being done.
 The vehicle should not have any snow, ice
or mud attached to it.
 Tires should be inflated to the prescribed
pressure.
 Close all doors.
 Rock the vehicle to stabilize the suspen-
sion.
Headlight aiming is done with the vehicle
low beam lamps. The high beam lamps will 1 Wall or garage door.
2 25 ft (7.6 m) between wall and headlight lens.
3 Measurement from the ground to the low beam aiming marker on the headlight lens.
4 Same measurement as (3) but substract 2 inches.
Vertical aiming device1 Aiming marker on headlight lens
93U S M 06.book Page 284 Friday, February 18, 2005 1:15 PM
ProCarManuals.com

285 Car care
be correctly aimed if the low beam lamps
are aimed properly.
If you find that the headlight needs adjust-
ment follow these steps:
1 Open the hood and locate the vertical
aiming devices there are two vertical
aiming devices which shall be turned
simultaneously and the same amount of
turns.
2 Locate the marker on the lens.
3 Measure the distance from the ground to
the aim marker No.1 on each lens.
Subtract 2 inches.
4 At the wall or other flat surface, measure
from the ground to the recorded
distance (see point 4) and draw a hori-
zontal line the width of the vehicle.
5Cars with xenon lights:
Xenon lights with automatic headlight
levelling system must first do a refer-
ence run before aiming: Start the engine
and let the headlights do a reference
run. Turn off the engine but leave the low
beam on.
Cars with halogen lights:
Turn on the low beam headlights.
Both variants:
Place a piece of cardboard or equivalent
(although not directly on the lens) in front
of the headlight not being aimed. This
should allow the beam cut-off of the
headlight being aimed to be seen on the
flat surface.6 Turn the two vertical aiming screws
simultaneously in the same direction
indicated on the headlight until the hori-
zontal cut-off of the headlight is aligned
with the horizontal line on the wall.
7 If an optical headlight aimer device is
used follow point 1 and 2 and center the
lens of the optical headlight aimer
device at the intersection of the two
markers on the headlight lens.Then follow the instructions in the optical
headlight aimer instruction manual and
point 1, 2, 5, and 6 in this instruction.
NOTICEDo not cover a headlight directly on the
lens to improve beam cut-off when
aiming. Covering a headlight may cause
excessive heat build-up that may cause
damage to the headlight.Horizontal line on wall or other flat surface
Correctly adjusted low beam
93U S M 06.book Page 285 Friday, February 18, 2005 1:15 PM
ProCarManuals.com

314 IndexDriving in hot climates
____________ 197
Driving techniques
______________ 193
Driving with a heavy load on hilly
roads
________________________ 175
Driving with a load
______________ 204
Driving with a roof load ___________ 202
Driving with the compact spare wheel
208
Driving with the trunk lid open
______ 204
EEasy entry, Convertible
____________ 75
Economical motoring
____________ 193
Electric engine heater ____________ 194
Electric heating, front seats
___ 114
, 123
Electric windows
________________ 129
Electric windows, Convertible
_______ 79
Electrical system, technical data ____ 300
Electrically adjustable seats
________ 20
Electronic steering wheel lock _____ 162
Electronic Stability Program (ESP)
__ 185
Emergency opening of the narrow
backrest
_____________________ 150
Emergency operation of the sunroof
_ 140
Engine bay, cleaning
____________ 277
Engine heater
__________________ 194
Engine immobilizer
_______________ 57
Engine number
_________________ 307
Engine oil, checking
_____________ 219
Engine oil, grade
________________ 298
Engine oil, volume ______________ 299Engine temperature gauge
_________ 90
Engine, description
______________ 215
Engine, technical data ____________ 297
Engines
_______________________ 300
Event Data Recorders (EDR)
______ 292
Extra electrical socket
____________ 144
EDR (Event Data Recorders)
______ 292
ESP, anti-skid system
____________ 185
FFacilitating entry to rear seat,
Convertible
____________________ 75
Factors affecting fuel consumption
__ 193
Filler cap
______________________ 168
Filling a portable fuel container
_____ 169
Filling up
______________________ 167
Flat spots, tires
_________________ 259
Floor jack
_____________________ 274
Folding down the rear seat
________ 146
Front fog lights
_________________ 104
Front towing eye ________________ 205
Fuel container
__________________ 169
Fuel gauge
_____________________ 91
Fuel grade _____________________ 299
Fuel information
________________ 169
Functions, car alarm ______________ 61
Fuse panel in luggage compartment
_250
Fuse table
_____________________ 249
Fuses
________________________ 247
GGear selector indicator, automatic
transmission
___________________ 92
Gearbox number ________________ 307
General safety instructions,
Convertible
____________________ 64
Glove box
_____________________ 144
Glovebox lighting
________________ 244
GDO, garage door opener
_________ 134
HHandbrake
_____________________ 187
Hazard warning lights
____________ 105
Head restraint, Convertible
_________ 76
Head restraints
__________________ 23
Headlight flasher ________________ 103
Headlight levelling _______________ 102
Headlights
_____________________ 102
Heated door mirrors
_____________ 114
Hood
_________________________ 214
Horn __________________________ 128
Horn button
____________________ 128
IIf a tire goes flat
_________________ 264
Ignition switch
__________________ 160
Immobilizer
_____________________ 57
93U S M 06.book Page 314 Friday, February 18, 2005 1:15 PM
ProCarManuals.com

317 Index
Tire inspection and rotation
_______ 258
Tire markings
__________________ 266
Tire pressure monitoring, automatic
_ 254
Tire sidewall labeling
____________ 264
Tire sizes
_____________________ 304
Tire terminology and definitions
____ 267
Tire, changing
__________________ 273
Tire, spare
_____________________ 270
Tires
_________________________ 256
Tools and spare wheel
___________ 270
Touching up paintwork ___________ 279
Towbar
_______________________ 198
Towbar load
___________________ 200
Towing
_______________________ 205
Towing a trailer
_________________ 198
Towing the car _________________ 206
Traction Control System (TCS)
_____ 183
Transmission oil, checking
________ 222
Transmission oil, grade
___________ 301
Transmission, automatic __________ 173
Transmission, manual
____________ 172
Transporting the car
_____________ 207
Treadwear indicators ____________ 259
Trip computer
___________________ 94
Trip meter
______________________ 89
Troubleshooting, A/C and ACC
____ 282
Trunk lid, driving when open
_______ 204
Trunk lid, opening
________________ 53
Turbo gauge
____________________ 90
TCS
__________________________ 183
UUniform tire quality grading
________ 261
Upholstery care
_________________ 276
Upholstery, cleaning
_____________ 276
Useful tips on night driving
________ 205
Useful tips on starting
____________ 163
VVanity mirror
___________________ 142
Vehicle identification number
______ 307
Vehicle recovery
________________ 207
Vehicle Data Collection
___________ 292
WWarning labels
___________________ 8
Warning lights
___________________ 84
Warning triangle ________________ 105
Warnings and messages on SID,
Convertible
____________________ 73
Washer fluid ___________________ 230
Washer jets ____________________ 231
Washers
______________________ 106
Washing ______________________ 277
Washing a Convertible
___________ 278
Waxing and polishing
____________ 279
Wear indicators, tires ____________ 259What Will You See After an Airbag
Inflates?
______________________ 43
Wheel replacement
______________ 262
Wheels and tires, sizes ___________ 304
When it is time for new tires
_______ 259
Windshield washers
_____________ 106
Windshield wipers
_______________ 106
Wing mirrors
___________________ 132
Winter driving __________________ 195
Winter tires
____________________ 269
Wiper blades ___________________ 230
Wipers
________________________ 106
XXenon headlights
________________ 233
Xenon headlights, head light levelling
102
93U S M 06.book Page 317 Friday, February 18, 2005 1:15 PM
ProCarManuals.com