ESP SAAB 9-5 2006 Owners Manual

44 SecurityDoorsDoor handlesPull the handle to open the door.
If the door is stuck (e.g. if frozen), hold the
handle from above to secure a better grip.Central locking
Key / Remote control The key unit consists of a mechanical key
with integrated remote control.
The mechanical key is used for manual
locking and unlocking.
The remote control is used for remote lock-
ing and unlocking.
The key fits all the car’s locks.
The key supplied with the car has a code
number on a black plastic tag that needs to
be quoted for ordering additional keys. You
should therefore make a careful note of the
number.
The key contains a unique electronic code
for your car. When the key is inserted in the
ignition, the code is checked. If it matches,
the car can be started.
Your car is supplied with two keys. It is pos-
sible to have up to four keys for a car at one
time. If you loose one key you should have
this replaced as soon as possible by con-
tacting your Saab dealer. When the new key
is programmed into the system, the missing
key is automatically erased.
NOTE: For this reason, we strongly advise
you to take two keys with you on long jour-
neys and to keep them separate. If all keys
are lost, it will be necessary to replace costly
electronic components as well as the keys.
This loss and replacement cost is not cov-
ered by the new car warranty.
If an additional key is to be added, all of the
original keys must be brought to the dealer
so that the control module can ”learn” to rec-
ognize the new components.To check the number of keys that are pro-
grammed for the car; see page 54.
WARNING
Leaving children or pets unattended in a
locked car is dangerous. It is also danger-
ous to leave children in a vehicle with the
ignition key. A child or others could be
badly injured or even killed.
NOTICEThe key contains delicate electronics.
 Do not expose it to water.
 Avoid rough handling.
 Do not place the key where it may be
subjected to high temperatures, e.g.
on the instrument panel.
 The key may malfunction if it becomes
very cold. Warm it in your hands for a
couple of minutes.
 Never open the key. For changing the
battery, see page 49.
95usM06.book Page 44 Thursday, November 17, 2005 8:59 AM
ProCarManuals.com

45 Security
Locking/unlocking the carWhen the car is locked and unlocked the
theft alarm is also affected.
Remote locking
Press once on the control: all doors
locked.
The hazard warning lights will flash once.
The trunk/tailgate release switch on the
driver´s door will not work when all doors are
locked.
It is now not possible to unlock the doors
from within using the button on the
centre console.
Remote unlocking
Press once on the control: the driver´s
door is unlocked. Press a second time to
unlock the rest of the doors but not the
trunk/tailgate.
The hazard warning lights will flash twice.The central locking can also be operated
from inside the car by means of the
switch on the center console.
This switch is inoperative when the car is
locked from the outside using the remote
control.
The interior locking buttons on each door
affect only the respective door.
If the car is left with the doors open, the inte-
rior lighting and the courtesy lights in the
doors will be switched off automatically after
20 minutes, to prevent a drain on the bat-
tery. In such cases the electrically operated
seats will not function.
IB3153
3
2 1
Key / Remote control1To lock
2 To unlock
3 Opening the trunk (9-5 Sedan)
Unlocking the tailgate (9-5 SportCombi)
IB451
Switch for operation of central locking
95usM06.book Page 45 Thursday, November 17, 2005 8:59 AM
ProCarManuals.com

46 Security
If remote unlocking should fail to work
Unlock the front door with the key. To
silence the alarm, insert the key into the igni-
tion switch and turn it to the ON position.
The car can now be started. Contact a work-
shop to have the system checked and
repaired. We recommend that you contact
an authorized Saab dealer.
Locking by key (1)
When the car is locked and unlocked the
theft alarm is also affected.
Turn the key clockwise: all doors locked.
The trunk/tailgate release/unlock switch on
the driver’s door will not work when all doors
are locked. Nor will the switch on the center
console.
Unlocking by key (2)
Turn the key counterclockwise once: the
driver´s door will unlock.
Turn the key counterclockwise twice: all
doors, but not tailgate, unlocked. Switch in
driver´s door and switch in center console
enabled.
WARNING
The remote control also works from inside
the car. Therefore, hold the key in such a
way that the buttons are not unintention-
ally pressed when the key is turned, or
inserted or removed from the ignition
switch.
Otherwise, the doors may be unintention-
ally locked or the tailgate unlocked. On
Sedan models, the trunk may even be
opened.
Having the doors locked when you are
driving will reduce the likelihood of:
 Passengers, especially children,
opening doors and falling out of the
car.
 Intruders entering the car when it is
moving slowly or at a standstill.
However, you must also remember that
locked doors can hamper rescuers in the
event of a crash.
IB1555
2
1
Locking/unlocking by key1To lock
2 To unlock
95usM06.book Page 46 Thursday, November 17, 2005 8:59 AM
ProCarManuals.com

63 Instruments and controls
The ESP indicator light is located in the
tachometer and will be illuminated when
ESP regulation is occurring, i.e. when there
is insufficient traction between the tires and
the road surface to provide the grip required
for the acceleration called for. The driver
can also sense that the engine is not
responding normally to the accelerator.
Operation of the ESP indicates reduced
traction between the tires and the road, and
that extra care should be taken by the driver.
In normal driving, the ESP will help to
improve both ride comfort and safety, but
must not be regarded as a system to enable
the driver to drive at or maintain a higher
rate of speed. The same precautions for
safe cornering and driving on slippery roads
must still be applied (see page 165).The indicator light goes on when the Elec-
tronic Stability Program is switched off with
the ESP-button.
IMPORTANT: the system is automatically
engaged every time the engine is started
(see page 165).
The indicator light also goes on when there
is a fault in the system. In this case the light
cannot be turned off by means of the ESP
button. If a fault is indicated, have the
system checked by an authorized Saab
dealer.
See also “Electronic Stability Program
(ESP) on page 165.
Indicator ESP
Indicator ESP OFF
95usM06.book Page 63 Thursday, November 17, 2005 8:59 AM
ProCarManuals.com

66 Instruments and controlsCheck fuse 1 (radiator fan) in the fuse panel
under the hood, see page 223.
If the needle repeatedly enters the red zone,
stop the car as soon as it is safe to do so and
check the coolant level by looking at the
level visible through the plastic tank – do not
remove the cap. If the coolant level falls below the MIN mark,
the Saab Information Display (SID) will dis-
play the message
”Coolant level low.
Refill.”.

Pressure gaugeThe turbo gauge indicates the air volume for
combustion, which is equivalent to the
engine load.
Under certain barometric conditions, the
needle may enter the first part of the red
zone without necessarily indicating that a
fault has arisen.
If the needle repeatedly enters the red zone
and the engine at the same time loses
power because the monitoring system is
limiting boost pressure, you should contact
a workshop immediately. We recommend
that you contact an authorised Saab work-
shop.
NOTICEIf the needle, despite the above action,
enters the red zone, stop the car immedi-
ately, let the engine idle.
If the needle stays in the red zone, stop
the engine.
WARNING
Never open the cap of the expansion tank
completely when the engine is hot, open
with care. The pressure in the cool-
ing-system can cause hot coolant and
steam to be released. Failure to heed this
warning may result in personal injury.
IB3852
95usM06.book Page 66 Thursday, November 17, 2005 8:59 AM
ProCarManuals.com

68 Instruments and controlsSaab Information
Display (SID) The Saab Information Display (SID) shows
CHECK messages and incorporates eight
trip-computer functions.
Use the i/SET button to browse the func-
tions.
Outdoor temperature(Frost warning)
Regardless of which function has been
selected, except Night Panel Mode, SID will
automatically display the outdoor tempera-
ture when it is between 26° and 38°F (–3°
and +3°C). This also applies if the
temperature has moved outside the range
of 21° to 43°F (–6° to +6°C) but is again
between 26° and 38°F (–3° and +3°C).

WARNING
It is strongly recommended that the SID
settings be changed only when the car is
stationary. The driver’s attention can oth-
erwise easily be distracted from the road.
SID provides the following function:
Tem p .Outside temperature
D.T.E.Estimated range (distance to
empty fuel tank)
Fuel ØAverage fuel consumption
since function last reset
Dist.Distance to destination/Trip
meter
Speed ØAverage speed since function
last reset
AlarmAlarm function
Speed W.Speed warning
WARNING
Remember that roads can be icy even at
temperatures of above 38°F (+3°C),
especially on bridges and stretches of
road that are sheltered from the sun.
IB3928
SID, buttons and display
95usM06.book Page 68 Thursday, November 17, 2005 8:59 AM
ProCarManuals.com

70 Instruments and controlsUsing Dist. as a trip meter
If no value is programmed in Dist., it func-
tions as a trip meter. This is indicated by an
arrow to the right in the display.
Reset the trip meter by briefly pressing the
CLR button.
For the first kilometre, the distance will be
shown in increments of 10 metres; thereaf-
ter, the reading will change in increments of
100 metres.
Calculating the arrival time if a specified
average speed is maintained:
1 Select Dist.
2 Set the distance.
3 Select Speed Ø.
4 Set the average speed you intend to
drive at.
5 SID switches to Dist. automatically. The
calculated arrival time is now displayed
to the right.
The Speed Ø function will show actual
values once you start driving.Average fuel consumption, Fuel Ø
The average fuel consumption is calculated
using the values for fuel consumed and dis-
tance driven since last reset. This value is
stored in the car’s trip computer even when
the engine is switched off.
To reset the value, hold CLR depressed
until a chime sounds. The text Cleared is
displayed.
Resetting valuesTo reset the value, hold CLR depressed
until a chime sounds. The text Cleared is
displayed.
The following functions will be reset simulta-
neously:
D.T.E. (the value is reset to the distance
that can be reached with the amount of
remaining fuel if fuel consumption is
1.0 l/10 km; lower fuel consumption
increases this distance)
Fuel Ø (the value is reset to 1.0 l/10 km)
Speed Ø (average speed)
Values programmed in Dist., Alarm and
Speed W. are not reset. See respective
function
95usM06.book Page 70 Thursday, November 17, 2005 8:59 AM
ProCarManuals.com

72 Instruments and controlsNIGHT PANELTo improve night-driving conditions inside
the car, the Night Panel mode can be
selected. In this mode, the amount of infor-
mation displayed is reduced, and only the
most important instruments and displays
will be illuminated.
When the NIGHT PANEL button is pressed,
only the speedometer will be illuminated, all
the other instruments illumination being
extinguished and their needles moved to
zero. The SID display will be extinguished
and the backlighting for switches and other
controls will be dimmed. Note: All indicator
and warning lights, together with the display
of CHECK messages, will operate as nor-
mal, except ”Outdoor temperature”, see
page 68.The following conditions will wake up the
respective displays in the Night-Panel
mode:
 Setting of the Audio system or, SID (dis-
play comes on for ten seconds).
 CHECK message generated in the SID.
 High engine revs cause the rev counter to
be illuminated until the engine speed has
fallen again.
 If the quantity of fuel remaining falls below
4 gallons (15 liters), the fuel gauge will be
illuminated.
 If the engine temperature rises above nor-
mal, the temperature gauge will be illumi-
nated.
 In cars with automatic transmission, if the
selector lever is moved from D to position
M or L, the selector indication on the main
instrument panel will be illuminated.
To restore the displays and lighting to the
normal mode, press the NIGHT PANEL but-
ton.
Units and language versionsThe SID has four sets of units: CHECK messages can be displayed in six
language options: English, Swedish,
German, French, Italian and Spanish. Selecting units and language 1 Switch off the engine.
2 Briefly press i/SETbutton. Repeat this
until LANGUAGE/UNITS is displayed.
3 Hold i/SET depressed until a chime
sounds. Then select language using
or .
4 Briefly press the i/SET button. Then
select the units using or .
5 Briefly press the i/SET button. METRIC US GB IMPERIAL
km miles miles miles
km/h mph mph mph
liters US gal gallon gallon
°C °F °C °F
24-hour 12-hour 12-hour 12-hour
95usM06.book Page 72 Thursday, November 17, 2005 8:59 AM
ProCarManuals.com

75 Instruments and controls
Instrument illuminationThe brightness of the instrument illumina-
tion can be varied by means of the dimmer
switch adjacent to the headlight switch.
(See also Night panel on page 72).
In daylight or other equally bright light, the
instrument and switch illumination is auto-
matically extinguished.
Turn signal and lane change
indicatorsTo switch on the turn signals/lane change
indicators, move the stalk up or down.
The stalk has fixed positions for indicating a
right or left turn, and the indicators are can-
celled automatically (stalk returns to off
position).
The stalk also has an intermediate,
spring-loaded position that is useful for sig-
nalling when changing lanes or passing.
The respective indicator lights on the instru-
ment panel flash at the same frequency as
the direction indicators.
IB3856
102
IB4126
Turn signal and lane change indicators 1 Right indicators
2 Left indicators
Instrument illumination95usM06.book Page 75 Thursday, November 17, 2005 8:59 AM
ProCarManuals.com

81 Instruments and controls
Temperature control The cabin is divided into two temperature
zones:
 The driver’s zone
 The passenger zone (front and rear
seats)
The desired temperature can be set
between 60 and 80°F.
The displayed temperature is not the abso-
lute temperature but corresponds to the
comfort level normally experienced at that
temperature after allowance has been
made for the air flow, relative humidity, solar
radiation, etc., currently prevailing inside
the car.
 The most usual temperature setting is
64–76°F, depending on personal prefer-
ence and what clothing is worn.
 To allow the system time to adjust,
changes in the temperature setting shall
only be made in steps of 2°F.
Once the desired climate has been
achieved, the rear center vents can be
closed to prevent warm air being distributed
at face height.
When the ignition is switched off, only the
temperature control affects the system the
next time the engine is started. The system
will warm up/cool down to the temperature
to which the control is set.MAX heat, red indication
The HI setting is obtained by turning the
temperature control to the first position past
80 (to the red LED). The driver’s side selec-
tion regulates air distribution and recircula-
tion status. Temperature, however, can be
adjusted on the passenger side.
Settings when HI is selected:
 Maximum heat
 Air distribution to windshield and floor
 Recirculation OFF (even if manually
selected before)
 Fan: high speed
MAX cooling, blue indicator
The LO setting is obtained by turning the
temperature control to the first position past
60 (to the blue LED). The driver’s side selec-
tion regulates air distribution and recircula-
tion status. Temperature, however, can be
adjusted on the passenger side.
Settings when LO is selected:
 Maximum cooling (A/C compressor will
run even if AC OFF manually selected
before)
 Air distribution through panel vents
 Fan: maximum speed
 Recirculation ON
IB369
Air vent at rear side window 95usM06.book Page 81 Thursday, November 17, 2005 8:59 AM
ProCarManuals.com