lock SATURN L-SERIES 2004 Manual PDF

5. Push headlamp housing lever up to disengage
headlamp housing from headlamp housing
pocket.
6. Turn the bulb socket being replaced
counterclockwise one–quarter of a turn while
pressing the socket in rmly. Pull the socket
rearward until the bulb clears the headlamp housing,
and lift it up to access the bulb.7. Disconnect the wire connector from the bulb by
lifting the lock tab and pulling it away from the
plastic base.
8. Remove the bulb assembly and replace it with the
appropriate bulb.
5-48
ProCarManuals.com

Fog Lamps
1. Reach up from underneath the front body panel
and turn the bulb socket counterclockwise one–
quarter of a turn while pressing the socket in rmly.
Pull the socket rearward until the bulb clears the
fog lamp housing.
2. Disconnect the wire connector from the bulb by
lifting the lock tab and pulling it away from the
plastic base.
3. Remove the bulb assembly and replace it with the
appropriate bulb.
Center High-Mounted Stoplamp
(CHMSL) (Sedan)
1. Remove the center high mounted stop lamp cover
by pulling down on the cover edges.
2. Turn the bulb socket being replaced
counterclockwise one–quarter of a turn and remove
the bulb.
3. Replace it with the appropriate bulb.
5-49
ProCarManuals.com

Center High-Mounted Stoplamp
(CHMSL) (Wagon)
1. Open the liftgate.
2. Remove the center high mounted stop lamp cover
by pulling down on the cover edges.
3. Turn the bulb socket being replaced
counterclockwise one–quarter of a turn and remove
the bulb.
4. Replace it with the appropriate bulb.
Taillamps, Turn Signal, Stoplamps
and Back-up Lamps (Sedan)
1. Open the trunk.
2. Pull back with interior trim.
5-50
ProCarManuals.com

3. Remove fasteners from backside of taillamp
housing.4. Remove taillamp housing from body of vehicle.
5. Turn the bulb socket being replaced
counterclockwise one–quarter of a turn while
pressing the socket in rmly. Pull the socket
rearward until the bulb clears the taillamp housing.
6. Replace it with the appropriate bulb.
5-51
ProCarManuals.com

Taillamps, Turn Signal, Stoplamps
and Back-up Lamps (Wagon)
1. Open the liftgate.
2. Remove the interior access trim panel.
3. Turn the bulb socket being replaced
counterclockwise one–quarter of a turn while
pressing the socket in rmly. Pull the socket
rearward until the bulb clears the taillamp housing.
4. Replace it with the appropriate bulb.
Replacement Bulbs
Exterior Lamp Bulb Number
Headlamps —
High Beam 9005 HB39441732
Low Beam 9006 HB49441733
Front Park/Turn Lamps 34571999381
Front Side Markert Lamps W5W12092811
Stop/Taillamps P21/5W21019520
Rear Turn Lamps P21W21019521
Back-up Lamps P21W21019520
CHMSL PC16825085970
Fog Lamps 880L12450143
5-52
ProCarManuals.com

Changing a Flat Tire
If a tire goes at, avoid further tire and wheel damage
by driving slowly to a level place. Turn on your
hazard warning ashers.
{CAUTION:
Changing a tire can be dangerous. The vehicle
can slip off the jack and roll over or fall on you
or other people. You and they could be badly
injured or even killed. Find a level place to
change your tire.
CAUTION: (Continued)
CAUTION: (Continued)
To help prevent the vehicle from moving:
1. Set the parking brake rmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in the
vehicle.
To be even more certain the vehicle won’t
move, you should put blocks at the front and
rear of the tire farthest away from the one
being changed. That would be the tire, on the
other side, at the opposite end of the vehicle.
5-70
ProCarManuals.com

Removing the Wheel
You must take off the wheel cover or hubcap to reach
the wheel bolts.
For steel wheels with full plastic covers and aluminum
wheels with large circular center caps, do the following:
1. Loosen all ve hex-shaped plastic caps by turning
the wrench counterclockwise. Do not try to remove
plastic caps from the cover or center cap.
2. Pull the cover or center cap away from the wheel
and place it in the trunk.
When reinstalling full plastic covers or center caps,
tighten all ve plastic caps hand snug with the aid of the
wheel wrench and tighten them with the wheel wrench
an additional one–quarter of a turn.
Removing the Flat Tire and Installing
the Spare Tire
1. Use the wheel wrench to loosen all the wheel nuts.
Don’t remove them yet.
2. The jack has a bolt head at the end. Attach the
wheel wrench to the jack bolt head and rotate
the wheel wrench clockwise (to the right). That will
raise the lift head a little.
3. Move the jack over to where the at tire is.
5-74
ProCarManuals.com

6. Raise the vehicle by turning the jack handle
clockwise. Raise the vehicle far enough off the
ground so there is enough room for the compact
spare tire to t underneath the wheel well.
7. Remove all of the wheel nuts.
8. Take off the tire and wheel.9. Remove any rust or dirt
from the wheel bolts,
mounting surfaces
and spare wheel.
{CAUTION:
Rust or dirt on the wheel, or on the parts to
which it is fastened, can make the wheel bolts
become loose after a time. The wheel could
come off and cause an accident. When you
change a wheel, remove any rust or dirt from
the places where the wheel attaches to the
vehicle. In an emergency, you can use a cloth
or a paper towel to do this; but be sure to use
a scraper or wire brush later, if you need to, to
get all the rust or dirt off.
5-76
ProCarManuals.com

{CAUTION:
Never use oil or grease on wheel bolts. If you
do, the wheel bolts might come loose. Your
wheel could fall off, causing a serious
accident.
10. Place the compact spare tire on the wheel-mounting
surface.
11. Reinstall the wheel nuts. Tighten each nut by hand
until the wheel is held against the hub.
12. Lower the vehicle by turning the jack handle
counterclockwise.
5-77
ProCarManuals.com

Power Windows and Other Power
Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and
closes, protecting the circuit until the problem is xed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by fuses. This greatly reduces the chance
of circuit overload and re caused by electrical
problems.
There are three fuse blocks — the underhood fuse
block, the driver’s side oor console fuse block and the
passenger’s side oor console fuse block.
To identify and check fuses and relays, refer to the
Fuse Usage Chart on the inside surface of the
fuse panel door.
Floor Console Fuse Blocks
The driver’s side instrument panel is located by the
driver’s left leg.
Use a key or a coin to remove the fuse panel door and
access the fuses and relays.
5-92
ProCarManuals.com