headrest SATURN OUTLOOK 2008 Owners Manual

Folding the Rear Seat
To fold the second row seats:
1. Remove anything on or under the seat.
2. Place the armrest in the upright position, and
unfasten the safety belt.
3. Pull forward on the reclining seatback strap (B) and
push down on the seatback.
4. If the headrest hits the front seat, slide the second
row seat rearward.
To return the seatback to the seating position, lift the
upper corner of the seatback and push it rearward until
it locks into place. Push and pull on the seatback to
make sure it is locked.
Adjusting the Seats
To adjust the second row seats, pull outward on the
seat adjustment handle (A). Slide the seat forward or
rearward to the desired position. Release the handle
and push and pull on the seat to make sure it is locked.
Third Row Seats
{CAUTION:
Using the third row seating position while the
second row is folded, or pushed forward in the
entry position, could cause injury in a sudden
stop or crash. Be sure to return the seat to the
passenger seating position. Push and pull on
the seat to make sure it is locked into place.
The third row seats can be folded forward or removed.
Notice:Folding a rear seat with the safety belts
still fastened may cause damage to the seat or
the safety belts. Always unbuckle the safety belts
and return them to their normal stowed position
before folding a rear seat.
1-14
ProCarManuals.com

To fold the seatback:
1. Remove anything on or under the seat.
2. Disconnect the rear safety belt mini-latch, using
a key in the slot on the mini-buckle, let the belt
retract into the headliner. Stow the mini-latch in
the holder located in the headliner.3. Pull up on the release
lever located on the
back of the seat.
The headrest moves
forward automatically.
4. Push the seatback forward to lay at.
1-15
ProCarManuals.com

To return the seatback to the seating position:
1. Raise the seatback into place by using the pullstrap
from the rear of the vehicle, or by pushing it into
place from inside the vehicle.
2. The headrest must be locked into place before
sitting in the seat.
{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there. Always
push and pull on the seatback to be sure it is
locked.
3. Push and pull on the seatback to make sure it is
locked in place.
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not provide
the protection needed in a crash. The person
wearing the belt could be seriously injured.
After raising the rear seatback, always check
to be sure that the safety belts are properly
routed and attached, and are not twisted.
4. Reconnect the center safety belt mini-latch to the
mini-buckle. Do not let it twist.
5. Pull on the safety belt to be sure the mini-latch is
secure.
1-16
ProCarManuals.com

Removing the Third Row Seats
1. Remove the cargo management system, if it is in
the vehicle. SeeCargo Management System on
page 2-59.
2. Remove anything on or under the seat.
Notice:Folding a rear seat with the safety belts
still fastened may cause damage to the seat or the
safety belts. Always unbuckle the safety belts
and return them to their normal stowed position
before folding a rear seat.
3. Fold the seatback down. See “Folding the Seatback”
earlier in this section.
4. Remove the rear bolts located on the oor on each
side of the seat.
5. Remove the seat by tilting it slightly upward, and
then pulling it out of the rear of the vehicle in one
motion.
6. Put the bolts back into the holes on the oor so
they do not get misplaced.
Installing the Third Row Seats
1. Before installing the seat the seatback must be
folded forward. See “Folding the Seatback”
earlier in this section.
The seats must be placed in the proper locations
for the legs to attach correctly. The wider seat must
be installed on the driver side and the narrower
seat on the passenger side. Remove the bolts from
the holes in the oor before installing the seats.
2. Place the seat on the vehicle oor so that the front
seat hooks are on the vehicle bars.
3. Reinstall the bolts, and torque to 55Y(41 lb ft).
Pull up on the seat to make sure it is locked in place.
4. Raise the seatback to its upright position. Push
and pull on the seatback to make sure it is locked
into place.
5. Push the headrest up into position. Push and
pull on the headrest to make sure it is locked
into place.
6. Reconnect the center safety belt mini-latch to the
mini-buckle. Do not let it twist.
1-17
ProCarManuals.com

There is a guide for each outboard passenger position
in the second row seat and all passenger positions
in the third row. Here is how to install a comfort guide
to the safety belt:
1. For the outboard positions, remove the guide from
its storage clip on the interior body.
For the third row center position, locate the comfort
guide which is located in a storage pocket, at
the top of the seat, under the headrest on thedriver’s side of the vehicle. To access the comfort
guide, you will rst need to move the headrest
forward by pulling on the handle behind the
seatback. The comfort guide will now be
accessible.
Pull the comfort guide out
of its storage location and
then return the headrest
to its upright position.
The elastic cord on the comfort guide is adjustable.
You can make it longer or shorter by squeezing
both ends of the plastic adjuster. Outboard Positions
Third Row Center
Position
1-35
ProCarManuals.com

Notice:Do not let the LATCH attachments rub
against the vehicle’s safety belts. This may damage
these parts. If necessary, move buckled safety
belts to avoid rubbing the LATCH attachments.
Do not fold the empty rear seat with a safety belt
buckled. This could damage the safety belt or
the seat. Unbuckle and return the safety belt to
its stowed position.
1. Attach and tighten the lower attachments to the
lower anchors. If the child restraint does not have
lower attachments or the desired seating position
does not have lower anchors, secure the child
restraint with the top tether and the safety belts.
Refer to your child restraint manufacturer
instructions and the instructions in this manual.
1.1. Find the lower anchors for the desired
seating position.
1.2. Recline the seatback to the full reclined
position.
Make sure the second row bench seatbacks
are aligned at the same angle before placing
the child restraint on the seat. Make sure the
third row bench seatbacks are both upright
before placing the child restraint on the seat.
1.3. Put the child restraint on the seat.
1.4. Attach and tighten the lower attachments on
the child restraint to the lower anchors.2. If the child restraint manufacturer recommends that
the top tether be attached, attach and tighten the
top tether to the top tether anchor, if the vehicle has
one. Refer to the child restraint instructions and
the following steps:
2.1. Find the top tether anchor.
2.2. If the anchor is covered, ip open the cover
to expose the anchor.
2.3. Route, attach and tighten the top tether
according to your child restraint instructions
and the following instructions:
If the position you are
using does not have a
headrest or head restraint
and you are using a
single tether, route the
tether over the seatback.
1-55
ProCarManuals.com

If the position you are
using does not have a
headrest or head restraint
and you are using a dual
tether, route the tether over
the seatback.
If the position you are
using has a xed headrest
or head restraint and you
are using a dual tether,
route the tether around the
headrest or head restraint.If the position you are
using has a xed headrest
or head restraint and you
are using a single tether,
route the tether over the
headrest or head restraint.
3. Push and pull the child restraint in different
directions to be sure it is secure.
1-56
ProCarManuals.com