wheel bolts SATURN VUE 2007 Owners Manual

Wheel Alignment and Tire Balance
The tires and wheels on your vehicle were aligned
and balanced carefully at the factory to give you
the longest tire life and best overall performance.
Adjustments to wheel alignment and tire
balancing will not be necessary on a regular basis.
However, if you notice unusual tire wear or your
vehicle pulling to one side or the other, the
alignment may need to be checked. If you notice
your vehicle vibrating when driving on a smooth
road, your tires and wheels may need to be
rebalanced. See your retailer for proper diagnosis.
Wheel Replacement
Replace any wheel that is bent, cracked or badly
rusted or corroded. If wheel nuts keep coming
loose, the wheel, wheel bolts and wheel nuts
should be replaced. If the wheel leaks air, replace
it (except some aluminum wheels, which can
sometimes be repaired). See your dealer/retailer
if any of these conditions exist.
Your dealer/retailer will know the kind of wheel
you need.
Each new wheel should have the same
load-carrying capacity, diameter, width, offset and
be mounted the same way as the one it replaces.
382
ProCarManuals.com

If you need to replace any of your wheels, wheel
bolts or wheel nuts, replace them only with
new Saturn original equipment parts. This way,
you will be sure to have the right wheel, wheel
bolts and wheel nuts for your vehicle.
{CAUTION:
Using the wrong replacement wheels,
wheel bolts, or wheel nuts on your vehicle
can be dangerous. It could affect the
braking and handling of your vehicle,
make your tires lose air and make you
lose control. You could have a collision
in which you or others could be injured.
Always use the correct wheel, wheel bolts,
and wheel nuts for replacement.Notice:The wrong wheel can also cause
problems with bearing life, brake cooling,
speedometer or odometer calibration,
headlamp aim, bumper height, vehicle ground
clearance, and tire or tire chain clearance
to the body and chassis.
SeeChanging a Flat Tire on page 386for more
information.Used Replacement Wheels
{CAUTION:
Putting a used wheel on your vehicle is
dangerous. You cannot know how it has
been used or how far it has been driven.
It could fail suddenly and cause a crash.
If you have to replace a wheel, use a new
Saturn original equipment wheel.
383
ProCarManuals.com

Removing the Flat Tire and
Installing the Spare Tire
The wheel cover or hubcap needs to be removed
in order to reach the wheel bolts.
For steel wheels with full plastic covers and
aluminum wheels with large circular center caps,
do the following:
1. It is recommended that a safety check is done
before preceding. SeeChanging a Flat Tire
on page 386for more information.
2. Loosen all plastic
caps by turning the
wheel wrench
counterclockwise.
Do not try to remove
plastic caps from
the cover or
center cap.
3. Pull the cover or center cap away from the
wheel and place it in the trunk.When reinstalling full plastic covers or center
caps, tighten all the plastic caps hand snug, then
tighten with the wheel wrench an additional
one-quarter of a turn.
1. Use the wheel wrench to loosen all the wheel
nuts. Do not remove them yet.
2. Attach the wheel
wrench to the jack
bolt head and
rotate the wheel
wrench clockwise.
That will raise the lift
head a little.
391
ProCarManuals.com

8. Remove any rust or
dirt from the wheel
bolts, mounting
surfaces and
spare wheel.
9. Place the compact spare tire on the
wheel-mounting surface.
{CAUTION:
Never use oil or grease on studs or nuts.
Because the nuts might come loose. The
vehicle’s wheel could fall off, causing a
serious accident.
10. Reinstall the wheel nuts. Tighten each nut by
hand until the wheel is held against the hub.11. Lower the vehicle by turning the jack handle
counterclockwise.
395
ProCarManuals.com

{CAUTION:
Incorrect wheel nuts or improperly
tightened wheel nuts can cause the wheel
to come loose and even come off. This
could lead to an accident. Be sure to use
the correct wheel nuts. If you have to
replace them, be sure to get new GM
original equipment wheel nuts. Stop
somewhere as soon as you can and have
the nuts tightened with a torque wrench
to the proper torque specication. See
Capacities and Specifications on page 414
for wheel nut torque specication.
Notice:Improperly tightened wheel nuts can
lead to brake pulsation and rotor damage.
To avoid expensive brake repairs, evenly
tighten the wheel nuts in the proper sequence
and to the proper torque specication. See
Capacities and Specifications on page 414for
the wheel nut torque specication.12. Tighten the wheel
nuts rmly in a
crisscross sequence,
as shown.
13. Lower the jack all the way and remove the
jack from under the vehicle.
14. Tighten the bolts rmly with the wheel wrench.
Notice:Wheel covers will not t on your
vehicle’s compact spare. If you try to put a
wheel cover on the compact spare, the cover or
the spare could be damaged.
396
ProCarManuals.com