jump cable SATURN VUE HYBRID 2007 Owners Manual

36-Volt Battery System
If you need a new 36-volt hybrid battery system,
see your retailer.
Vehicle Storage
If you are not going to drive your vehicle for
30 days or more you should disconnect the
standard 12-volt battery by disconnecting the
negative battery cable, the one that is exposed.
Remember to reconnect the battery when you are
ready to drive your vehicle.
Notice:The 36-volt hybrid battery system
should be serviced only by a qualied facility
to avoid battery system damage. See your
retailer if service is needed.
Notice:If the vehicle is not driven for over
two months, the 36-volt hybrid battery can be
permanently damaged.
The 36-volt battery is located behind the rear seat,
under the cargo oor. If the vehicle is stored for
an extended period of time, drive the vehicle every
two months for about half an hour to keep the
36-volt hybrid battery charged and in good working
condition.
Jump Starting
Your hybrid vehicle has a standard 12-volt battery
in the engine compartment, and a 36-volt
battery under the rear load oor.
{CAUTION:
Personal injury or damage to the vehicle
can result if you try jump starting or using
a battery charger on the 36-volt battery.
Use only the 12-volt battery for jump
starting and charging.
If your vehicle’s standard 12-volt battery has run
down, you may want to use another vehicle
and some jumper cables to start your vehicle.
Be sure to use the following steps to do it safely.
322
ProCarManuals.com

{CAUTION:
Batteries can hurt you. They can be
dangerous because:
They contain acid that can burn you.
They contain gas that can explode or
ignite.
They contain enough electricity to
burn you.
If you do not follow these steps exactly,
some or all of these things can hurt you.
Notice:Ignoring these steps could result in
costly damage to your vehicle that would
not be covered by your warranty.Trying to start your vehicle by pushing or
pulling it will not work, and it could damage
your vehicle.
1. Check the other vehicle. It must have a
12-volt battery with a negative ground system.
Notice:If the other vehicle’s system is not a
12-volt system with a negative ground,
both vehicles can be damaged. Only use
vehicles with 12-volt systems with negative
grounds to jump start your vehicle.
2. Get the vehicles close enough so the jumper
cables can reach, but be sure the vehicles are
not touching each other. If they are, it could
cause a ground connection you do not
want. You would not be able to start your
vehicle, and the bad grounding could damage
the electrical systems.
To avoid the possibility of the vehicles rolling,
set the parking brake rmly on both vehicles
involved in the jump start procedure.
Put an automatic transaxle in PARK (P) or a
manual transaxle in NEUTRAL before
setting the parking brake.
323
ProCarManuals.com

6. Check that the jumper cables do not have
loose or missing insulation. If they do, you
could get a shock. The vehicles could
be damaged too. Before you connect the
cables to the other vehicle, here are some
basic things you should know. Positive (+) will
go to positive (+) or to a remote positive
terminal (+) if the vehicle has one.
Negative (−) will go to a heavy, unpainted
metal engine part or to a remote negative (−)
terminal, if the vehicle has one. Do not
connect positive (+) to negative (−) or you will
get a short that would damage the battery
and maybe other parts too.
7. Connect the red positive (+) cable to the
remote positive (+) terminal of your hybrid
vehicle.8. Do not let the other end touch metal. Connect
it to the positive (+) terminal of the good
battery. Use a remote positive (+) terminal if
the other vehicle has one.
9. Now connect the black negative (−) cable to
the negative (−) terminal of the good battery.
Use a remote negative (−) terminal if the
vehicle has one. Do not let the other end
touch anything until the next step. The other
end of the negative (−) cable does not go
to the dead battery. It goes to your vehicle’s
remote negative (−) terminal. The electrical
connection is just as good there, and the
chance of sparks getting back to the battery is
much less.
10. Try to start the hybrid vehicle.
326
ProCarManuals.com

Notice:If the jumper cables are connected or
removed in the wrong order, electrical shorting
may occur and damage the vehicle. The repairs
would not be covered by your warranty. Always
connect and remove the jumper cables in the
correct order, making sure that the cables do
not touch each other or other metal.
A. Heavy, Unpainted Metal Engine Part or
Remote Negative (−) Terminal
B. Good Battery or Remote Positive (+) and
Remote Negative (−) Terminals
C. Dead Battery or Remote Positive (+) TerminalTo disconnect the jumper cables from both
vehicles, do the following:
1. Disconnect the black negative (−) cable from
the vehicle that had the dead battery.
2. Disconnect the black negative (−) cable from
the vehicle with the good battery.
3. Disconnect the red positive (+) cable from the
vehicle with the good battery.
4. Disconnect the red positive (+) cable from the
other vehicle.
5. Return the underhood fuse block cover and
engine cover to their original positions.
Jumper Cable Removal
327
ProCarManuals.com