headlamp SATURN VUE HYBRID 2009 Owner's Manual
[x] Cancel search | Manufacturer: SATURN, Model Year: 2009, Model line: VUE HYBRID, Model: SATURN VUE HYBRID 2009Pages: 346, PDF Size: 2.1 MB
Page 256 of 346

Front Turn Signal and
Parking Lamps
To replace a front turn signal or
parking lamp bulb:
1. Follow Steps 1 through 6 under
Headlamps on page 5-35to
access the front turn signal or
parking lamp.
2. Turn the bulb to be replaced
counterclockwise to remove
it from the headlamp assembly.3. Pull the bulb out of the bulb
socket assembly.
4. Push the new bulb into the bulb
socket assembly.
5. Insert the bulb assembly into the
headlamp assembly.
6. Turn the bulb assembly
clockwise until seated.
7. Reverse the steps to reinstall the
headlamp assembly.
Taillamps, Turn Signal,
Stoplamps and Back-up
Lamps
To replace one of these bulbs:
A. Taillamp/Stoplamp
B. Turn Signal Lamp
C. Back-up Lamp
5-36 Service and Appearance Care
ProCarManuals.com
Page 257 of 346

1. Open the liftgate.
2. Remove the two screws holding
in the taillamp assembly.
3. Slide the taillamp assembly
rearward and away from the
vehicle.
4. Turn the bulb socket being
replaced counterclockwise
to disconnect it.
5. Pull the bulb out of the bulb
socket.
6. Push the new bulb into the
bulb socket.
7. Reverse Steps 2 through 4 to
reinstall the taillamp assembly.License Plate Lamp
To replace one of these bulbs:
1. Remove the two screws holding
each of the license plate lamps
to the fascia.
2. Turn and pull the license plate
lamp forward through the
fascia opening.
3. Turn the bulb socket
counterclockwise and pull the
bulb straight out of the socket.4. Push the new bulb into the bulb
socket and turn it clockwise to
lock it into place.
5. Push and turn the license plate
back through the fascia opening.
6. Reinstall the two screws holding
the license plate lamps to the
fascia.
Replacement Bulbs
Exterior Lamp Bulb
Number
Back-up Lamp 3156
Front Turn
Signal/Parking3157K
Headlamps
High-beam9005 or
HB3
Low-beam/DRL9006 or
HB4
Rear Turn Signal,
Stoplamp and
Taillamp3057
For replacement bulbs not listed
here, contact your dealer/retailer.
Service and Appearance Care 5-37
ProCarManuals.com
Page 276 of 346

Your dealer/retailer will know the
kind of wheel you need.
Each new wheel should have the
same load-carrying capacity,
diameter, width, offset and be
mounted the same way as the
one it replaces.
{CAUTION
Using the wrong replacement
wheels, wheel bolts, or wheel nuts
on your vehicle can be
dangerous. It could affect the
braking and handling of your
vehicle, make your tires lose air
and make you lose control. You
could have a collision in which
you or others could be injured.
Always use the correct wheel,
wheel bolts, and wheel nuts for
replacement.If you need to replace any of your
wheels, wheel bolts, or wheel
nuts, replace them only with new
Saturn original equipment parts.
This way, you will be sure to have
the right wheel, wheel bolts,
and wheel nuts for your vehicle.
Notice:The wrong wheel
can also cause problems with
bearing life, brake cooling,
speedometer or odometer
calibration, headlamp aim,
bumper height, vehicle ground
clearance, and tire clearance
to the body and chassis.
{CAUTION
Rust or dirt on a wheel, or on
the parts to which it is
fastened, can make wheel
nuts become loose after a
time. The wheel could come
off and cause a crash. When
you change a wheel, remove
any rust or dirt from places
where the wheel attaches to
the vehicle. In an emergency,
you can use a cloth or a paper
towel to do this; but be sure to
use a scraper or wire brush
later, if you need to, to get all
the rust or dirt off.
{CAUTION
Never use oil or grease on studs
or the threads of the wheel nuts.
If you do, the wheel nuts might
come loose and the wheel could
fall off, causing a crash.
5-56 Service and Appearance Care
ProCarManuals.com