engine Seat Alhambra 2010 Owner's Manual

Wheels and tyres343
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Raise the vehicle using only the designated jacking points.
Check list
For your own safety and that of other passengers, the following points should
be observed in the order given Ÿ:
1. Select a suitable flat and firm surface for raising the vehicle.
2. Switch off the engine, engage a gear (manual gearbox) or place the
selector lever in position P Ÿpage 201 and turn on the electronic
parking brake Ÿpage 210.
3. When towing a trailer: unhook the trailer from the towing vehicle and
park it correctly.
4. Loosen the wheel bolts on the wheel to be changed Ÿpage 340.
5. Look below the vehicle for the jacking point Ÿpage 342, fig. 192
closest to the tyre which has to be changed.
6. Raise the jack with the handle until it can be inserted below the jacking
point.
7. Ensure that the foot of the jack is firmly on the ground and that it is
placed immediately below the lifting point on the vehicle Ÿpage 342,
fig. 193.
8. Straighten the jack and continue raising it using the handle until the claw
holds the vertical reinforcement beneath the vehicle Ÿpage 342,
fig. 193.
9. Raise the vehicle until the wheel is clear of the ground.
WARNING
If the vehicle is not correctly raised, it could fall off the jack causing serious
injury. Please observe the following rules to minimise the risk of injury:
xYou should only use a jack approved by SEAT for your vehicle. Other
jacks, even those approved for other SEAT models, might slip out of place.
xThe ground should be firm and flat. If the ground is sloped or soft then
the vehicle could slip and fall off the jack. If necessary, support the jack on
a wide solid base.
xIf the ground is slippery (for example, on tiles), place a non-slip surface
(for example a floor mat) beneath the jack to avoid slipping.
xOnly fit the jack at the prescribed jacking points. The claw of the jack
should grip the reinforcement nerve on the underbody Ÿpage 342,
fig. 193.
xYou should never have any limbs beneath a raised vehicle which is only
supported by a jack.
xIf you have to work underneath the vehicle, you must use suitable
stands additionally to support the vehicle, there is a risk of accident!.
xNever raise the vehicle if it is tilting to one side or the engine is running.
xNever start the engine when the vehicle is raised. The vehicle may come
loose from the jack due to the engine vibrations.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
WARNING (continued)

If and when 346
3. Connect the electronic parking brake Ÿpage 210.
4. Move the selector lever to its intermediate position or to P Ÿpage 201.
5. Stop the engine and remove the key from the ignition Ÿpage 195.
6. Have all occupants leave the vehicle and move to safety, for example
behind a guard rail.
7. When leaving the vehicle, take all keys with you.
8. Place an emergency warning triangle to indicate the position of your
vehicle to other road users.
9. Allow the engine to cool and check if a specialist is required.
Examples of when to use the hazard warning lights:
xIf the vehicles ahead suddenly slow down or reach the end of a traffic jam,
to warn the vehicles behind.
xIn case of an emergency.
xIf the vehicle breaks down.
xWhen being towed.
Always comply with the applicable laws regarding the use of hazard warning
lights.
If the hazard warning lights are not working, you must use an alternative
method of drawing attention to your vehicle. This method must comply with
traffic legislation.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
WARNING
The components of the exhaust system reach very high temperatures. This
could cause a fire and considerable damage.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as dried grass or fuel).
Note
The vehicle battery will discharge and run down if the hazard warning lights
remain on for too much time (even with the ignition turned off).
Note
For some vehicles, the brake lights will blink when braking suddenly at
speeds of approximately 80 km/h to warn vehicles behind. If braking
continues, then the hazard warning lights will automatically be turned on at
the speed of less than approximately 10 km an hour. The brake lights remain
lit. Upon accelerating, the hazard warning lights will be automatically turned
off.

If and when 352
Manually unlocking the gear selection lever
If the vehicle power supply should ever fail (discharged battery, etc.) and the
vehicle has to be pushed or towed, the selector lever must first be moved to
position N using the manual release mechanism.The emergency release mechanism is located underneath the gearbox cover
panel to the right-hand side. To release the gear selector lever mechanism, a
suitable tool is required, for example a screwdriver.
Preparations
xApply the parking brake. If the parking brake cannot be activated in the
vehicle must be secured otherwise so that it cannot move.
xSwitch the ignition off.
To remove the gearbox cover panel
xPull the cover up around the dust guard on the gear selector lever
Ÿfig. 204.
xTake the cover off by passing it over the gear selector lever Ÿ.
Manual release of selector lever
xPress the release lever Ÿfig. 205 in the direction of the arrow and hold it
in this position.
xPress the lock button Ÿfig. 204 on the gear selector lever knob and
place the gear selector lever in the N position.
WARNING
Never move the gear selector lever from the position P while the electronic
parking brake is deactivated. Otherwise, the vehicle may accidentally
move off on hills or steep slopes causing serious accidents.
Caution
If the vehicle is moved on its wheels with the engine stopped and the selector
lever in position N for a prolonged period of time and at high speed, for
example for towing, then the automatic gearbox will be damaged.
Fig. 204 Remove the
lining from the area of the
gear indication.
Fig. 205 Manual release
of gear selector lever.
A1

If and when353
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
To o l s *
Introduction
When securing the vehicle in case of a breakdown, please note the legal
requirements for each country.
Additional information and warnings:
xWorking in the engine compartment Ÿpage 304
xChange wheel Ÿpage 339
xIn case of emergency Ÿpage 345
WARNING
Loose objects in the passenger compartment can be violently fired through
the compartment in case of a sudden manoeuvre or braking and especially
in accidents causing serious injury.
xMake sure that the vehicle tools are stored safely in the luggage
compartment.
WARNING
Unsuitable or damaged on-board tools can cause injury or accidents.
xNever work with inappropriate or damaged tools.
Location
Depending on the model, the vehicle tools may be kept in the luggage
compartment, in a cavity close to the lock carrier Ÿfig. 206. Loosen the
safety straps and remove the on-board tools. For vehicles factory-fitted with
winter tyres, you will find additional tools in a toolbox located in the luggage
compartment.
Note
After use, return the jack to its initial position using the handle in order to
securely store it in the vehicle.
Fig. 206 In the luggage
compartment, viewed
from inside the vehicle:
On-board tools are
located in a cavity close to
the lock carrier.

If and when 356
Fuses
Introduction
Due to the constant update of vehicles, fuse assignments depending on
equipment and the use of the same fuse for various electrical components, at
the time of printing this manual it is not possible to provide an up-to-date
summary of the electrical components fuse positions. For detailed informa-
tion about the fuse positions, please consult a qualified workshop.
In general, a fuse can be assigned to various electrical components. Like-
wise, an electrical component can be protected by several fuses.
Only replace fuses when the cause of the problem has been solved. If a newly
inserted fuse blows after a short time, you must have the electrical system
checked by a qualified dealership as soon as possible.
Additional information and warnings:
xWorking in the engine compartment Ÿpage 304
WARNING
The high voltages in the electrical system can give serious electrical
shocks, causing burns and even death!
xNever touch the electrical wiring of the ignition system.
xTake care not to cause short circuits in the electrical system.
WARNING
Using unsuitable fuses, repairing fuses or bridging a current circuit without
fuses can cause a fire and serious injury.
xNever use a fuse with a higher value. Only replace fuses with a fuse of
the same amperage (same colour and markings) and size.
xNever repair a fuse.
xNever replace a fuse by a metal strip, staple or similar.
Caution
xTo avoid damage to the vehicles electric system, before replacing a fuse
turn off the ignition, the lights and all electrical elements and remove the
keys from the ignition.
xIf you replace a fuse with higher-rating fuse, you could cause damage to
another part of the electrical system.
xProtect the fuse boxes when open to avoid the entry of dust or humidity.
Dirt and humidity inside fuse boxes can cause damage to the electrical
system.
Note
One single consumer could have more than one fuse.
Note
Several consumers could run over one single fuse.
WARNING (continued)

If and when357
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Vehicle fuses
Only replace fuses with a fuse of the same amperage (same colour and mark-
ings) and size.Identifying fuses by colours
To open the dashboard fuse box
xReach behind the cover with your hand Ÿfig. 209 and pull forwards.
To open the engine compartment fuse box
xOpen the bonnet ’ Ÿpage 304.
xMove the attachment tabs forwards, in the direction indicated by the
arrow to release the fuse box cover Ÿfig. 210.
xThen lift the cover out.
xTo fit the cover, place it on the fuse box. Push the attachment tabs back,
in the opposite direction indicated by the arrow until they click audibly into
place.
In is possible that there are more fuses behind a cover in the lower left-hand
side of the luggage compartment.
Fig. 209 On the driver-
side dashboard: fuse box
cover.
Fig. 210 In the engine
compartment: fuse box
cover.
ColourAmp rating
purple3
light brown5
Brown7,5
Red10
Blue15
Yellow20
White or transparent25
Green30
orange40

If and when 360
Changing bulbs
Introduction
Changing bulbs requires a certain amount of manual skill. If you are unsure,
SEAT recommends that you consult an qualified workshop or request assist-
ance from a specialist. In general, a specialist is required if other vehicle
components must be removed or if the discharge lamps must be replaced.
You should store spare light bulbs in the vehicle for safety-relevant lights.
Spare bulbs may be obtained from the Official dealers and workshops. In
some countries, it is a legal requirement to carry spare bulbs in the vehicle.
Driving with faults and blown bulbs on the vehicle exterior lighting is against
the law.
Additional bulb specifications
The specifications of some headlamp bulbs and bulbs for the tail lamps fitted
at the factory may be different to those of conventional bulbs. Bulb informa-
tion is displayed on the bulb socket or on the bulb itself.
Additional information and warnings:
xLights and visibility Ÿpage 113
xWorking in the engine compartment Ÿpage 304
xVehicle tools Ÿpage 353
xFuses Ÿpage 356
WARNING
If the road is not well-lit and the vehicle is not clearly visible to other
drivers, there is a risk of accident.
WARNING
Failure to replace bulbs correctly may cause serious accidents.
xBefore carrying out any work in the engine compartment please read
and observe the warnings Ÿpage 304. In any vehicle, the engine compart-
ment is a hazardous area and could cause severe injury.
xDischarge lamps work with high-voltage and can cause serious or fatal
injury if handled incorrectly.
xH7 and discharge lamps are highly pressurised and could explode
when being changed.
xOnly replace the bulbs concerned when they have cooled.
xNever replace bulbs alone if you are not familiar with the operations
necessary. If you are not sure about procedures then visit a qualified work-
shop to carry out the necessary work.
xNever touch the bulb glass directly. Fingerprints will be evaporated by
the heat of the operating bulb thus “fogging” up the reflector.
xThe headlamp frameworks in the engine compartment and the tail
lamps contain sharp elements. Always protect your hands when changing
bulbs.
Caution
After changing a bulb, if the rubber covers and plastic caps are not replaced
correctly on the headlamp framework, the electrical installation may be
damaged, especially if water is allowed to enter.

If and when361
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Indicator
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Checking the bulbs of a trailer
For vehicles with the factory fitted trailer system, certain trailer lights are also
controlled if the socket is correctly connected.
A fault on a trailer turn indicator is indicated on the instrument panel by the
indicator blinking twice as fast (
 or
) Ÿpage 113.
xGeneral fault of all indicators on one side.
xFault in one tail light (on some models, also the registration light).
xFault in two brake lights.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Note
A fault in the LED on the tail lights will not be indicated. However, if the fault
affects all the LEDs then this will be indicated by the indicator .
Information for replacing bulbs
Checklist
To replace a bulb, carry out the following operations always in the order given
Ÿ:
1. Park the vehicle a safe distance from traffic and on suitable ground.
2. Connect the electronic parking brake Ÿpage 210.
3. Turn the light switch to position 0 Ÿpage 113.
4. Move the gear lever into the neutral position Ÿpage 113.
5. Automatic gearbox: Move selector lever to position P Ÿpage 201.
6. Stop the engine and remove the key from the ignition Ÿpage 195.
7. Manual gearbox: Select a gear Ÿpage 201.
8. Wait until all of the passenger compartment lights are turned off
Ÿpage 113.
9. Allow the corresponding bulb to cool.
10. Visually inspect fuses to see if any are blown Ÿpage 356.
11. Replace the bulb according to the instructions Ÿ. Bulbs should only
be replaced by new identical models. Bulb information is displayed on
the bulb socket or on the bulb itself.
12. In general, never touch the bulb glass directly. The heat of the bulb would
cause the fingerprint to evaporate and condense on the reflector. This
will impair the brightness of the headlight.
lights upPossible causeSolution
A vehicle exterior lighting
bulb is not working.Replace the faulty bulb.

If and when 362
13. Check if the new bulb is working. If the bulb is not working, it may not
have been correctly fitted, it could be damaged or the connector may not
be correctly connected.
14. Every time a bulb for the headlights is replaced, visit a specialised work-
shop to check the headlights.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
Caution
Always remove and fit headlights carefully to avoid damage to the paintwork
and other vehicle parts.
To replace halogen headlight bulbs
There is no need to remove the headlight to replace bulbs.
Complete operations only in the sequence given:
WARNING (continued)
Fig. 213 In the engine
compartment: Left-hand
side headlight lining.
dipped beam headlights,
daytime lights and
main beam headlights
and side lights.
AA
ABAC
Fig. 214 Left headlight

If and when 364
To replace the xenon headlights bulb
There is no need to remove the headlight to replace bulbs.
Complete operations only in the sequence given:Always seek the help of a specialist when changing the Xenon dipped beam
and full beam headlamps Ÿ in “Introduction” on page 360.
Note
The illustrations show the left hand headlight. The structure of the right hand
side headlight is symmetric.
Fig. 215 In the engine
compartment: Turn signal
cover.
Fig. 216 Turn signal indi-
cator lamp holder and
turning light .A1A2
Turn signal indicators Turning lights
1.Always take the checklist into account and take the necessary
actions Ÿpage 361.
2.Open the bonnet ’ Ÿpage 304.
3.Rotate the cover Ÿfig. 215 in the direction of the arrow and remove
it.
4.
Rotate the lamp holder
Ÿfig. 216 to the left all the way
and pull it out backwards with the
bulb.Press the wire clip downwards
and pull the lamp holder
Ÿfig. 216 out with the bulb.
5.Depending on the model, the bulb is removed directly from the lamp
holder or it may need to be rotated and then removed.
6.Replace the faulty bulb by a new identical bulb.
7.Place the bulb holder in the head-
light and rotate to the right all the
way.Place the lamp holder in the
headlight and pull the wire clip
upwards until it clicks into place.
8.Rotate the cover Ÿfig. 215 in the opposite direction to the arrow as
far as it will go.
A1A2
A1
A2