bonnet Seat Alhambra 2010 User Guide

Checking and refilling levels 304
Working in the engine compartment
Introduction
Before working in the engine compartment, make sure that the vehicle is
parked on horizontal and firm ground.
The engine compartment of the vehicle is a hazardous area. Never work on
the engine or in the engine compartment if you are not familiar with the oper-
ations to be carried out, the applicable safety standards and especially if you
do not have the instruments, liquids and tools necessary Ÿ! Have the
work carried out by a qualified workshop if you are uncertain. Negligent work
can cause serious injury.
Additional information and warnings:
xWindscreen wash system Ÿpage 124
xStart and stop the engine Ÿpage 195
xBrake fluid Ÿpage 210
xVehicle battery Ÿpage 318
xChecks when filling up Ÿpage 293
xEngine oil Ÿpage 309
xEngine coolant Ÿpage 313
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
If the vehicle moves unexpectedly, this could cause serious injury.
xNever work underneath the vehicle if it is not secured against moving.
If you must work underneath the vehicle with the wheels in contact with
the ground then it should be parked on flat ground, the wheels should be
prevented from moving and the key must be removed from the ignition.
xIf you have to work underneath the vehicle, you must use suitable
stands additionally to support the vehicle, there is a risk of accident!. The
jack is not intended for this kind of work and its failure could lead to severe
injuries.
WARNING
The engine compartment is a dangerous area capable of causing serious
injury.
xFor all type of work, always take the utmost precautions, work carefully
and note the general safety standards in force. Never take personal risks.
xNever work on the engine or in the engine compartment if you are not
familiar with the necessary operations. If you are not sure about proce-
dures then visit a qualified workshop to carry out the necessary work.
Incorrect work can cause serious injuries.
xNever open the bonnet if you see steam or coolant escaping from the
engine compartment. Hot vapours and coolant can cause serious burns.
Always wait until you cannot see or hear the sound of steam or coolant
coming from the engine compartment.
xAlways allow the engine to cool down before opening the bonnet.
xContact with hot elements of the engine and the exhaust system can
cause burns.
xOnce the engine has cooled, follow the instructions below before
opening the bonnet:
Turn on the electronic parking brake and place the gear selector lever
in P or the gear stick in neutral.
Remove the key from the ignition.
Keep children away from the engine compartment and never leave
them unsupervised.
WARNING (continued)

Checking and refilling levels307
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Opening and closing the bonnet
Opening the bonnet
The lever to open the bonnet can only be used if the driver's door is open.
xBefore opening the bonnet, make sure that the windscreen wiper arms are
in place against the windscreen Ÿ.
xOpen the driver's door.
xPull the release lever Ÿpage 307, fig. 173 in the direction of the arrow.
The bonnet is released from the lock carrier by a spring mechanism Ÿ.
xLift the bonnet using the release lever Ÿpage 307, fig. 174 (arrow) and
open the bonnet fully. The bonnet is held open thanks to the gas strut.
Closing the bonnet
xTo close the bonnet, pull it down to overcome the gas strut pressure
Ÿ.
xAllow the bonnet to fall into the lock carrier. Do not press down.
If the bonnet is not correctly closed, open it once again and close it correctly.
The bonnet is correctly closed when it is flush with the corresponding parts
on the bodywork.
WARNING
If the bonnet is not correctly closed, it could suddenly open while driving
leaving the driver without visibility. This could result in serious accident.
xAfter closing the bonnet, always check that it is properly secured by the
locking mechanism in the lock carrier. The bonnet must be flush with the
surrounding body panels.
xWhile driving, if you notice that the bonnet is not correctly closed then
stop immediately and close it correctly.
xOnly open and close the bonnet when there is nobody within its range.
Fig. 173 In the footwell
on the driver side: Lever
for unlocking the bonnet.
Fig. 174 Release lever to
open the bonnet in the
radiator grille.

Checking and refilling levels 308
Caution
xTo avoid damage to the bonnet and to the windscreen wiper arms, only
open the bonnet when the windscreen wipers are in place against the wind-
screen.
xBefore driving, always lower the wiper arms.

Checking and refilling levels311
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xStop the engine and wait a few minutes for the oil to drain back into the
sump. When the engine has cooled down, immediately check the oil level and
top up if necessary.
xOpen the bonnet ’ Ÿpage 304.
xThe engine oil filler opening can be recognised by the symbol E on the
cap Ÿpage 310, fig. 176 and the dipstick by its coloured handle.
Checking the engine oil level
xPull out the dipstick and wipe it on a clean cloth.
xReplace the dipstick, pushing it in as far as it will go. If the dipstick has a
mark, when you reintroduce it this mark should slot into the corresponding
groove located on the upper end of the tube.
xRemove the dipstick again and check the engine oil level Ÿtable on
page 311.
xAfter reading the oil level, replace the dipstick in the tube completely.
Engine oil topping up ranges
Adding oil after checking the level
Only add engine oil in small quantities and in steps.
xUnscrew the cap from engine oil filler opening on the cylinder head
Ÿpage 310, fig. 176. If you are not sure where the cap is, request help from
a specialist.
xOnly refill using engine oil expressly approved by SEAT and in small quan-
tities (not more than 0.5 L or 1/2 a quarter of a gallon at a time) Ÿpage 310.
xTo avoid adding too much oil, each time you add a quantity, wait until the
oil has flowed into the crankcase so that it can be measured with the dipstick.
xCheck the oil level before adding any more oil. Do not top up with too
much engine oil Ÿ.
xWhen the oil level is in at least the Ÿpage 310, fig. 175 zone, insert
the dipstick into the tube fully to avoid engine oil escaping when the engine
is running.
xAfter topping up the oil, ensure that the cap is screwed on to the filler
mouth correctly.
WARNING
Oil could catch fire if it comes into contact with hot engine components.
This could lead to a fire, explosion and severe injuries.
xAlways ensure that after topping of oil, the engine oil filler cap is
correctly tightened. This will avoid engine oil spilling onto hot engine parts
when the engine is running.
Caution
xIf the oil level is above the area Ÿpage 310, fig. 175 do not start the
engine. You should obtain professional assistance. Otherwise catalytic
converter and engine damage may occur.
xWhen refilling or changing service liquids, ensure that you put the liquids
into the right tank. Making a mistake when refilling could cause serious
malfunctions and damage the engine!
For the sake of the environment
The oil level must never be above area Ÿpage 310, fig. 175 . Otherwise
oil can be drawn in through the crankcase breather and escape into the
atmosphere via the exhaust system.
page 310,
fig. 175Operations required depending on the engine oil topping
up level:
Area Do not top up oil Ÿ.
Area Add approximately 0.5 L of oil (1/2 quarter of a gallon). The
oil level can be in the zone , but never above .
Area :
It is essential to add oil (approximately 1 litre or quarter of
a gallon). Ensure that the level is around the centre of the
zone after adding oil.
AA
ABAAAA
ACAB
AB
AA
AA

Checking and refilling levels 316
Preparations
xPark the vehicle on even, flat and firm ground.
xAllow the engine to cool Ÿ.
xOpen the bonnet ’ Ÿpage 304.
xThe coolant expansion reservoir is easily recognisable because of the
symbol « on the cap Ÿpage 315, fig. 179.
Checking the engine coolant level
xWhen the engine is cold, check the coolant level using the side marking
on the expansion reservoir Ÿpage 315, fig. 178.
xIf the level is below the “MIN” mark, top up with coolant. When the engine
is hot it may be slightly above the marked area.
Topping up the engine coolant level
xAlways protect your face, hands and arms from hot coolant and steam
using a large, thick cloth over the coolant expansion tank cap.
xRemove the cap very carefully Ÿ.
xOnly refill using new engine coolant according to SEAT specifications
(Ÿpage 314) Ÿ.
xThe engine coolant level should be between the marks on the coolant
expansion tank Ÿpage 315, fig. 178. Do not exceed the top level of the
marked area Ÿ.
xScrew on the cap tightly.
xIf, the event of an emergency, you have no coolant that is compliant to the
required specifications (Ÿpage 314), never use another type of additive.
Instead, first top up with distilled water Ÿ only. Then re-establish the
correct proportion of the mixture with the correct additive as soon as possible
Ÿpage 314.
WARNING
Hot vapours and coolant can cause serious burns.
xNever open the coolant expansion tank if steam or coolant is coming
from the engine compartment. Wait until you cannot see or hear any steam
or coolant escaping.
xAlways wait until the engine has completely cooled before very care-
fully opening the expansion tank cap. Contact with hot elements of the
engine can cause skin burns.
xOnce the engine has cooled, follow the instructions below before
opening the bonnet:
Turn on the electronic parking brake and place the gear selector lever
in P or the gear stick in neutral.
Remove the key from the ignition.
Keep children away from the engine compartment and never leave
them unsupervised.
xWhen the engine is warm or hot, the cooling system is pressurised! Do
not unscrew the cap on the expansion tank when the engine is hot. Other-
wise, coolant may spray out under pressure causing burns and serious
injury.
Carefully and slowly unscrew the cap anticlockwise, gently pressing
down on it.
Always protect your face, hands and arms from hot coolant and
steam using a large, thick cloth.
xWhen refilling liquids, avoid spilling them on parts of the engine and
the exhaust system. Spilled liquids could cause a fire. Under specific
circumstances, the ethylene glycol can catch fire.
Caution
xTop up with distilled water only. Any other type of water may lead to
considerable rusting in the engine due to its chemical components. This
could consequently damage the engine. If you have not used distilled water
WARNING (continued)

Checking and refilling levels 320
Start-Stop systems Ÿpage 223 are equipped with a special battery labelled
“AGM”. For technical reasons, it is not possible to check the electrolyte level
of these batteries
Preparations
xPrepare the vehicle for work in the engine compartment Ÿpage 304
xOpen the bonnet ’ Ÿpage 304.
Opening the battery cover
The battery covers are different depending on the engine size of the vehicle:
xIn the case of a cover: press the tab Ÿpage 319, fig. 180 in the direc-
tion of the arrow and pull the cover upwards.
xIn the case of a hose: fold the cover to one side to remove Ÿpage 319,
fig. 181.
Checking the battery electrolyte level
xMake sure there is sufficient lighting to clearly recognise the colours.
Never use open flames or sparklers as a light source.
xDepending on the level of acid, the Magic eye on the top of the battery will
change colour.
WARNING
Working with the vehicle battery involves a risk of corrosion, explosions
and electric shock.
xAlways wear protective gloves and eye protection.
xBattery acid is very corrosive and caustic. It can burn skin and cause
blindness. When handling the battery, protect yourself from splashes of
acids, above all your hands, arms and face.
xNever tilt the vehicle battery. Battery acid could spill out of the open-
ings to release gases and cause corrosion damage.
xNever open the vehicle battery.
xIf battery acid splashes on you, immediately rinse your eyes and skin
abundantly with water for several minutes. Then seek medical care imme-
diately.
xIf acid is swallowed by mistake, consult a doctor immediately.
Charging, replacing and connecting or disconnecting the
battery
Charging the battery
The vehicle battery should be charged by a specialist workshop only, as
batteries using special technology have been installed and they must be
charged in a controlled environment Ÿ. SEAT recommends visiting a qual-
ified workshop.
Replacing a vehicle battery
The battery has been developed to suit the conditions of its location and has
special safety features. If the battery must be replaced, consult a qualified
SEAT workshop for information on electromagnetic compatibility, the size
and maintenance, performance and safety requirements of the new battery in
your vehicle before you purchase one. SEAT recommends you have the
battery replaced by a qualified SEAT workshop.
Use only maintenance-free genuine batteries conforming to TL 825 06 and
VW 7 50 73 Standards. These standards must be dated April 2008 or later.
Colour indicatorNecessary operations
light yellow or col-
ourlessThe electrolyte level of the vehicle's battery is too low.
Have the battery checked and, where applicable,
replaced by a specialist workshop.
Black indicationThe electrolyte level of the vehicle's battery is correct.
AA
WARNING (continued)

If and when357
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Vehicle fuses
Only replace fuses with a fuse of the same amperage (same colour and mark-
ings) and size.Identifying fuses by colours
To open the dashboard fuse box
xReach behind the cover with your hand Ÿfig. 209 and pull forwards.
To open the engine compartment fuse box
xOpen the bonnet ’ Ÿpage 304.
xMove the attachment tabs forwards, in the direction indicated by the
arrow to release the fuse box cover Ÿfig. 210.
xThen lift the cover out.
xTo fit the cover, place it on the fuse box. Push the attachment tabs back,
in the opposite direction indicated by the arrow until they click audibly into
place.
In is possible that there are more fuses behind a cover in the lower left-hand
side of the luggage compartment.
Fig. 209 On the driver-
side dashboard: fuse box
cover.
Fig. 210 In the engine
compartment: fuse box
cover.
ColourAmp rating
purple3
light brown5
Brown7,5
Red10
Blue15
Yellow20
White or transparent25
Green30
orange40

If and when363
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
The images show the left hand headlight from behind. The structure of the
right hand side headlight is symmetric.
page 362, fig. 213,
page 362, fig. 214 Indicators (small lamp
holder)Dipped beam head-
lightsDaylight driving lightsMain beam headlightsSide lights
1.Always take the checklist into account and take the necessary actions Ÿpage 361.
2.Open the bonnet ’ Ÿpage 304.
3.Remove the rubber cover on the rear of the headlight.
4.
Rotate the lamp holder
to the left all the way
and pull it out back-
wards with the bulb.
Rotate the lamp holder to the left all the way and
pull it out backwards with the bulb.
Press the wire clip down-
wards and pull the lamp
holder out with the
bulb.Pull the lamp holder
out backwards with the
bulb.
5.Depending on the model, the bulb is removed directly from the lamp holder or it may need to be rotated and then removed.
6.Replace the faulty bulb by a new identical bulb.
7.Place the bulb holder in the headlight and rotate to the right all the way.
Place the lamp holder in
the headlight and pull the
wire clip upwards until it
clicks into place.Place the lamp holder in
the headlight and insert
completely.
8.Insert the rubber cover.
AAABAC
A1A2
A3

If and when 364
To replace the xenon headlights bulb
There is no need to remove the headlight to replace bulbs.
Complete operations only in the sequence given:Always seek the help of a specialist when changing the Xenon dipped beam
and full beam headlamps Ÿ in “Introduction” on page 360.
Note
The illustrations show the left hand headlight. The structure of the right hand
side headlight is symmetric.
Fig. 215 In the engine
compartment: Turn signal
cover.
Fig. 216 Turn signal indi-
cator lamp holder and
turning light .A1A2
Turn signal indicators Turning lights
1.Always take the checklist into account and take the necessary
actions Ÿpage 361.
2.Open the bonnet ’ Ÿpage 304.
3.Rotate the cover Ÿfig. 215 in the direction of the arrow and remove
it.
4.
Rotate the lamp holder
Ÿfig. 216 to the left all the way
and pull it out backwards with the
bulb.Press the wire clip downwards
and pull the lamp holder
Ÿfig. 216 out with the bulb.
5.Depending on the model, the bulb is removed directly from the lamp
holder or it may need to be rotated and then removed.
6.Replace the faulty bulb by a new identical bulb.
7.Place the bulb holder in the head-
light and rotate to the right all the
way.Place the lamp holder in the
headlight and pull the wire clip
upwards until it clicks into place.
8.Rotate the cover Ÿfig. 215 in the opposite direction to the arrow as
far as it will go.
A1A2
A1
A2

General notes on the technical data 380
Vehicle code
Vehicle identification number
The vehicle identification number (chassis number) can be read from outside
the vehicle through a viewer in the windscreen Ÿfig. 230. This viewer is
located in the lower part of the windscreen. The vehicle identification number
(chassis number) is also stamped on the right water drain channel. The water
drain channel is located between the suspension tower and the wing. Open
the bonnet to read the vehicle identification number
’ Ÿpage 304.
Vehicle data plate
The vehicle data plate is attached to the luggage compartment, and contains
the following information:
Vehicle identification number (chassis number)
Vehicle type, engine power, gearbox type
Engine and gearbox code, paint number, interior equipment.
Optional extras, PR numbers
These data are also provided in the Maintenance Programme.Type plate
The type plate is visible when the driver door is opened, on the lower part of
the strut. Vehicles for certain export countries do not have a type plate.
The manufacturer's type plate contains the following data:
Gross vehicle weight
Maximum authorised weight of vehicle and trailer
Maximum gross front axle weight
Maximum rear axle weight
Fig. 230 Vehicle identifi-
cation number.
A1
A2
A3
A4
A5
A6
A7
A8