battery Seat Alhambra 2010 Owner's Guide

Heating, Ventilation and Air conditioning189
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Replacing the remote control battery
When the light Ÿpage 188, fig. 132 on the remote control does not
come on when the button is pressed, the remote control battery should soon
be replaced.
The battery is located beneath a cover on the back of the remote control. Turn
the slot to the left using a flat, blunt object (e.g. a coin). When changing the
battery, use another battery of the same model and observe the polarity when
fitting it Ÿ.
Range
The receiver is in the interior of the vehicle. The remote control, when fitted
with new batteries, has a range of several hundred metres. Obstacles
between the remote control and the vehicle, bad weather conditions and
discharged batteries can considerably reduce the range of the remote control.
An optimum range is obtained by keeping the remote control vertical, with
the aerial Ÿpage 188, fig. 132 pointing upwards. When doing so, do not
cover the aerial with your fingers or with the palm of your hand.
There must be a minimum distance of two metres between the remote control
and the vehicle.
Caution
xThe radiofrequency remote control contains electronic components.
Therefore, avoid getting the remote control wet and from being knocked and
protect it from direct sunlight.
xUse of inappropriate batteries may damage the remote control. For this
reason, always replace the dead battery with another of the same voltage,
size and specifications.
For the sake of the environment
Please dispose of old batteries so that they do not harm the environment.
For the sake of the environment
The remote control battery may contain perchlorate. Observe the legal
requirements for their disposal.
Programming the auxiliary heater
The heater or ventilation inside the vehicle can be programmed for a certain
period.
Before programming, check that the day is correctly set in the Auxiliary
heater - day of the week menu Ÿ.
Enabling the Auxiliary heater menu on the instrument panel
xFrom the main menu, select the Auxiliary heater submenu and press the
button on the windscreen wiper lever.
xALTERNATIVELY: press the or arrow buttons on the multi-function
steering wheel until the Auxiliary heater menu is displayed.
a)Within its range, the remote control might not receive the signal sent by the vehicle
receiver. In this case, the remote control will send an error message despite the aux-
iliary heater being on or off. Come closer to the vehicle and press the corresponding
button on the remote control once again.
AB
AAOK
ƒ„

Heating, Ventilation and Air conditioning 190
Checking programming
If the timer has been switched on after switching the ignition off, the instant
on button will remain lit for around ten seconds.
WARNING
Never program the independent heating system to be activated and oper-
ated in closed, unventilated areas. The auxiliary heater fumes contain carbon dioxide, an odourless and colourless toxic gas. Carbon monoxide
can cause people to lose consciousness. It can also cause death.
User instructions
The auxiliary heater exhaust system located below the vehicle must be kept
clear of snow, mud and other objects. The exhaust fumes must not be
obstructed in any way. The exhaust fumes generated by the auxiliary heater
are removed via an exhaust pipe fitted underneath the vehicle.
On heating the vehicle interior, depending on the outside temperature the
warm air is first directed at the windscreen and then to the rest of the
passenger compartment through the air vents. If the air vents are turned
towards the windows, for example, the form of air distribution may be
affected.
Depending on the outside temperature, the temperature at which the auxil-
iary heater warms the vehicle interior may be somewhat higher if the heating
or climate control temperature control is set to maximum before switching the
heating on.
Depending on the engine, vehicles with auxiliary heater may be fitted with a
second battery in the luggage compartment that is responsible for powering
the auxiliary heater.
Cases in which the auxiliary heater will not switch on
xThe auxiliary heater requires about as much power as the dipped head-
lights. If the battery charge is low, the auxiliary heater will switch off automat-
ically or will not even switch on. This avoids problems when starting the
engine.
xThe heater will switch just once each time. The timer will also have to be
switched back on every time it is required.
Menu optionsDescription
Switching on
Switching off
The auxiliary heater can be set to come on automatically if
required. To do so, select a timer:
– The timer is displayed marked with a
y.
– Only one timer can be selected. If a timer has been
selected, Prog. ON will be displayed on the screen. If no
timer has been selected, the instrument panel screen will
display Prog. OFF.
– To modify the programmed timer, select another timer or
select the Off option.
Timer 1
Timer 2
Timer 3Three different timers (hh.mm) can later be selected using
the On option. If the auxiliary heater is to be switched on
for just a certain day of the week, select the day of the
week and the time for the auxiliary heater to come on.
DurationThe operating time may vary between 10 and 60 minutes
and can be set to 5-minute intervals.
Operating
modeSet to heat or ventilate the vehicle interior when the auxil-
iary heater is switched on.
DaySet the current day of the week.
Manufacturer's
settingsThe predefined factory values for the functions of this
menu are restored.
BackThis returns to the main menu
>
WARNING (continued)

Heating, Ventilation and Air conditioning191
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
Noise will be heard while the auxiliary heater is running.
Note
When the air humidity is high and the outside temperature low, the heating
system may evaporate condensation from the auxiliary heater. In this case,
steam may be released from underneath the vehicle. This is completely
normal and there is no need to suspect a fault!
Note
If the auxiliary heater runs several times over a prolonged period, the
vehicle's battery may run flat. To re-charge the battery, drive the vehicle for a
long distance. In general: drive for as much time as the auxiliary heating was
working.

Driving 192
Driving
Steering
Introduction
The power steering is not hydraulic but electromechanical. The advantage of
this steering system is that it disposes of hydraulic tubes, hydraulic oil, the
pump, filter and other components. The electromechanical system saves
fuel. While a hydraulic system requires oil pressure to be maintained, electro-
mechanical steering only requires energy when the steering wheel is turned.
With the power steering system, the assisted steering function automatically
adjusts according to the vehicle speed, the steering torque and the wheel
turning angle. The power steering only works when the engine is running.
Additional information and warnings:
xStart and stop the engine Ÿpage 195
xVehicle battery Ÿpage 318
xTow-starting and towing away Ÿpage 375
WARNING
If the power steering is not working then the steering wheel is much more
difficult to turn and the vehicle more difficult to control.
xThe power steering only works when the engine is running.
xNever allow the vehicle to move when the engine is switched off.
xNever remove the key from the ignition if the vehicle is in motion. The
steering may lock and it will not be possible to turn the steering wheel.
Control and warning lamps
lights upPossible causeSolution
D (red)Power steering faulty.The steering system should be
checked by a qualified workshop
as soon as possible.
D (yel-
low)
Power steering operation
reduced.
The steering system should be
checked by a qualified workshop
as soon as possible.
If, after restarting the engine and
driving for a short distance, the
yellow warning light no longer
comes on, it will not be neces-
sary to take the vehicle to a spe-
cialised workshop.
The vehicle battery was dis-
connected and has been
reconnected.Drive for a short distance at 15 –
20 km/h.

Driving 196
Ignition lock
Key not authorised for the vehicle
If a key which is not authorised for this vehicle is inserted in the ignition lock,
it can be removed as follows:
xAutomatic gearbox: the key cannot be removed from the ignition lock.
Press and release the selector lever locking button. Key can be removed from
the vehicle.
xManual gearbox: Remove the key from the ignition.
WARNING
Unsuitable or careless use of the vehicle key could result in serious injury.
xAlways take all the keys with you whenever you leave the vehicle. The
engine could accidentally be started and electrical equipment such as the
windows could accidentally be operated resulting in serious injury.
xNever leave children or disabled people alone in the car. They could be
trapped in the car in an emergency and will not be able to get themselves
to safety. For example, depending on the time of the year, temperatures
inside a locked and closed vehicle can be extremely high or extremely low
resulting in serious injuries and illness or even death, particularly for
young children.
xNever remove the key from the ignition if the vehicle is in motion. The
steering may lock and it will not be possible to turn the steering wheel.
Note
If the key is left in the ignition lock with the engine off for long periods, the
vehicle battery will run flat.
Fig. 134 Vehicle key positions
Car keys Ÿfig. 134
No key in the ignition lock: The steering lock may be activated.
Ignition off, all electrical components disconnected. Key can be
removed from the vehicle.
Ignition is switched on. Pre-heating of diesel engine. The steering
lock can be unlocked.
Switch on the engine. Release the key when the engine has started.
When it is released, the key returns to position .
A0
A1
A2A1

Driving197
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
For automatic gearbox vehicles the key can only be removed from the ignition
lock if the gear selector lever is in position P. In this case, press and release
the selector lever locking button.
Starter button*
The starter button can only be used if there is a valid key inside the vehicle.
On leaving the vehicle with the ignition switched off, the electronic lock on
the steering column is activated when the driver's door is opened
Ÿpage 192.
Switching the ignition on/off
xBriefly press the starter button once without pressing the clutch or brake
pedal Ÿ.Emergency starting function
If the system has not recognised a valid key inside the vehicle, the emergency
starter function is activated. The corresponding information text is displayed
on instrument panel. This may occur, for example, if the key battery is flat or
very low:
xPlace the key close to the steering column immediately after passing the
start button.
xThe engine starts automatically.
Emergency disconnection
If it is not possible to switch off the engine by briefly pressing the starter
button, the emergency disconnection system should be used:
xPress the starter button twice within a second or press it once for more
than two seconds Ÿ in “Stopping the engine” on page 199.
xThe engine turns off automatically.
Re-starting the engine
If, after the engine is switched off, a valid key is not detected in the vehicle,
the engine can only be started after an interval of approximately 5 seconds.
The corresponding message is displayed on the instrument panel.
After this interval, it will not be possible to start the engine without a valid key
inside the vehicle.
WARNING
Unintentional movements of the vehicle could cause serious injury.
xWhen the starter button is pressed do not press the brake or clutch
pedal as the engine will start immediately.
Fig. 135 Detailed view of
the centre console: KESSY
starter and lock system:
Starter button.

Driving199
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
Never leave the vehicle unattended if the engine is running. The vehicle
could move off suddenly, especially if it is in gear, resulting in an accident
and serious injury.
WARNING
Cold start sprays could explode or cause a sudden increase in the engine
speed.
xNever use start boosters.
Caution
xAn attempt to start the engine while driving or starting the engine imme-
diately after turning it off can cause damage to the engine or starter motor.
xWhen the engine is cold, avoid high revs and heavy acceleration and do
not make the engine work hard.
xDo not push or tow start the engine. Sunburnt fuel could damage the cata-
lytic converter.
For the sake of the environment
Do not warm the engine at idle speed; start driving immediately if the visi-
bility is OK. This helps the engine reach operating temperature faster and
reduces emissions.
Note
For example, if the key battery is very worn or flat, the engine cannot be
started with the starter button. In this case, remove the ignition button from
the lock and insert the key.
Note
Electrical components with a high power consumption are switched off
temporarily when the engine starts.
Note
When the engine is started cold, there may be strong vibrations for a few
moments for technical reasons. This is quite normal, and no cause for
concern.
Note
At temperatures below +5 °C (+41 °F), smoke may be given off below the
vehicle when the additional heater is connected.
Stopping the engine
Complete operations only in the sequence given:
StepVehicles without KESSYVehicles with KESSY
1.Stopping the vehicle completely Ÿ.
2.Press the brake pedal and keep pressed until step 4 has been com-
pleted.
3.In automatic gearboxes, put the selector lever in position P.
4.Connect the electronic parking brake Ÿpage 210.

Driving211
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Warning and control lamps
lights upPossible cause ŸSolution
H (red)
Together with the control
lamp
G on the button: Elec-
tronic parking brake on.Ÿpage 212
Fault in the brake system› Stop the vehicle!
Seek professional assistance!
Ÿpage 215.
Brake fluid level inadequate.› Do not drive on!
Check brake fluid level
Ÿpage 219.
Together with the ABS control
lamp
J: ABS fault.
Contact a specialist workshop.
The vehicle can be braked with-
out ABS.
K (red)Brake pedal not pressed!Press brake pedal to the floor.
I (yel-
low)Front brake pads worn.
Contact a specialist workshop
immediately. Inspect all the
brake pads and replace as nec-
essary.
« (yel-
low)
ESP disconnected by system.Switching the ignition on and off
If necessary, drive for a short
distance.
Fault in ESP.Contact a specialist workshop.
Together with the ABS control
lamp
J: Fault in ABS.
Contact a specialist workshop.
The vehicle can be braked with-
out ABS.
The battery has been recon-
nected.Ÿpage 318
l (yel-
low)TCS manually deactivated.
To turn on the TCS Ÿpage 218.
TCS is automatically activated
when the ignition is switched on
or off.
J (yel-
low)
Together with the ESP control
lamp
«: Fault in ABS.Contact a specialist workshop.
The vehicle can be braked with-
out ABS.
Together with the warning
lamp
H or : ABS fault.
 (yel-
low)Together with the warning
lamp
H flashing: Electronic
parking brake faulty.Contact a specialist workshop.
K
(green)Brake pedal not pressed.
Press the brake pedal to select a
gear ratio.
Press the brake pedal to discon-
nect the electronic parking
brake Ÿpage 212.
flashesPossible cause ŸSolution
H (red)
Electronic parking brake
faulty. The control lamp

may light up at the same time
or the control lamp
G may
flash on the button.
Contact a specialised workshop,
as it may not be possible to park
the vehicle in safety.
« (yel-
low)ESP or TCS adjusting.Take your foot off the accelera-
tor. Adjust your driving style to
the road conditions.
lights upPossible cause ŸSolution

Driving213
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xPress button . At the same time, press the brake pedal hard or gently
press the accelerator pedal with the engine switched on.
xThe control lamps G on the button and H on the instrument panel go
out.
Automatic release of the electronic parking brake on starting the engine
The electronic parking brake is automatically released when the vehicle starts
moving, if the driver's door is closed and the driver is wearing his/her seat
belt. In vehicles with a manual gearbox the clutch pedal should also be
pressed to the floor before starting the engine so that the system recognises
that the parking brake should be released.
Emergency braking function
Only use the emergency braking function if the vehicle cannot be stopped
with the brake pedal Ÿ!
xPull button hard to stop the vehicle. The warning display will be
accompanied by the corresponding warning chime.
xTo stop the braking process, release the button or press the accelerator.
WARNING
The incorrect use of the electronic parking brake may result in serious acci-
dent.
xNever use the electronic parking brake to brake the vehicle except in an
emergency. The braking distance is considerably longer, because braking
is only applied to the rear wheels. Always use the foot brake.
xNever accelerate from the engine compartment with the engine running
and a gear or a gear range engaged. The vehicle could move, even if the
parking brake is applied.
Note
In vehicles with a manual gearbox: When the clutch pedal is released and the
accelerator pressed at the same time, the electronic parking brake is auto-
matically released.
Note
If the vehicle battery is flat, it will not be possible to disconnect the electronic
parking brake. Use the jump-start Ÿpage 371.
Note
When the electronic parking brake is applied or released, noises may be
heard.
Note
If the electronic parking brake has not been used for a long while, the system
sometimes performs automatic and audible checks while the vehicle is at a
standstill.
Parking
When parking your vehicle, all legal requirements should be observed.
To park the vehicle
Complete operations only in the sequence given.
xPark the vehicle on a suitable surface Ÿ.
xPress and hold the brake pedal until the vehicle comes to a standstill.
xConnect the electronic parking brake Ÿpage 212.
xFor an automatic gearbox, move the selector lever to position P.
G
G

Driving221
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Start assist systems
Introduction
Additional information and warnings:
xSEAT information system Ÿpage 70
xBraking, stopping and parking Ÿpage 210
xVehicle battery Ÿpage 318
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
xJump starting Ÿpage 371
WARNING
The intelligent technology in the start assist systems cannot change the
laws of physics. The improved comfort provided by start assist systems
should not prompt you to take risks.
xUnintentional movements of the vehicle could cause serious injury.
xThe start assist systems are not a replacement for driver awareness.
xAlways try to adapt the speed of the vehicle and your style of driving to
the condition of the ground or the road and to weather and traffic condi-
tions.
xThe start assist system cannot keep the vehicle stationary in all condi-
tions on a gradient or cause it to brake on steep downhill gradients, e.g. if
the road is slippery or icy.