gearbox Seat Alhambra 2010 Owner's Guide
[x] Cancel search | Manufacturer: SEAT, Model Year: 2010, Model line: Alhambra, Model: Seat Alhambra 2010Pages: 413, PDF Size: 3.86 MB
Page 344 of 413

Wheels and tyres343
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Raise the vehicle using only the designated jacking points.
Check list
For your own safety and that of other passengers, the following points should
be observed in the order given Ÿ:
1. Select a suitable flat and firm surface for raising the vehicle.
2. Switch off the engine, engage a gear (manual gearbox) or place the
selector lever in position P Ÿpage 201 and turn on the electronic
parking brake Ÿpage 210.
3. When towing a trailer: unhook the trailer from the towing vehicle and
park it correctly.
4. Loosen the wheel bolts on the wheel to be changed Ÿpage 340.
5. Look below the vehicle for the jacking point Ÿpage 342, fig. 192
closest to the tyre which has to be changed.
6. Raise the jack with the handle until it can be inserted below the jacking
point.
7. Ensure that the foot of the jack is firmly on the ground and that it is
placed immediately below the lifting point on the vehicle Ÿpage 342,
fig. 193.
8. Straighten the jack and continue raising it using the handle until the claw
holds the vertical reinforcement beneath the vehicle Ÿpage 342,
fig. 193.
9. Raise the vehicle until the wheel is clear of the ground.
WARNING
If the vehicle is not correctly raised, it could fall off the jack causing serious
injury. Please observe the following rules to minimise the risk of injury:
xYou should only use a jack approved by SEAT for your vehicle. Other
jacks, even those approved for other SEAT models, might slip out of place.
xThe ground should be firm and flat. If the ground is sloped or soft then
the vehicle could slip and fall off the jack. If necessary, support the jack on
a wide solid base.
xIf the ground is slippery (for example, on tiles), place a non-slip surface
(for example a floor mat) beneath the jack to avoid slipping.
xOnly fit the jack at the prescribed jacking points. The claw of the jack
should grip the reinforcement nerve on the underbody Ÿpage 342,
fig. 193.
xYou should never have any limbs beneath a raised vehicle which is only
supported by a jack.
xIf you have to work underneath the vehicle, you must use suitable
stands additionally to support the vehicle, there is a risk of accident!.
xNever raise the vehicle if it is tilting to one side or the engine is running.
xNever start the engine when the vehicle is raised. The vehicle may come
loose from the jack due to the engine vibrations.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
WARNING (continued)
Page 353 of 413

If and when 352
Manually unlocking the gear selection lever
If the vehicle power supply should ever fail (discharged battery, etc.) and the
vehicle has to be pushed or towed, the selector lever must first be moved to
position N using the manual release mechanism.The emergency release mechanism is located underneath the gearbox cover
panel to the right-hand side. To release the gear selector lever mechanism, a
suitable tool is required, for example a screwdriver.
Preparations
xApply the parking brake. If the parking brake cannot be activated in the
vehicle must be secured otherwise so that it cannot move.
xSwitch the ignition off.
To remove the gearbox cover panel
xPull the cover up around the dust guard on the gear selector lever
Ÿfig. 204.
xTake the cover off by passing it over the gear selector lever Ÿ.
Manual release of selector lever
xPress the release lever Ÿfig. 205 in the direction of the arrow and hold it
in this position.
xPress the lock button Ÿfig. 204 on the gear selector lever knob and
place the gear selector lever in the N position.
WARNING
Never move the gear selector lever from the position P while the electronic
parking brake is deactivated. Otherwise, the vehicle may accidentally
move off on hills or steep slopes causing serious accidents.
Caution
If the vehicle is moved on its wheels with the engine stopped and the selector
lever in position N for a prolonged period of time and at high speed, for
example for towing, then the automatic gearbox will be damaged.
Fig. 204 Remove the
lining from the area of the
gear indication.
Fig. 205 Manual release
of gear selector lever.
A1
Page 362 of 413

If and when361
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Indicator
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Checking the bulbs of a trailer
For vehicles with the factory fitted trailer system, certain trailer lights are also
controlled if the socket is correctly connected.
A fault on a trailer turn indicator is indicated on the instrument panel by the
indicator blinking twice as fast (
or
) Ÿpage 113.
xGeneral fault of all indicators on one side.
xFault in one tail light (on some models, also the registration light).
xFault in two brake lights.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Note
A fault in the LED on the tail lights will not be indicated. However, if the fault
affects all the LEDs then this will be indicated by the indicator .
Information for replacing bulbs
Checklist
To replace a bulb, carry out the following operations always in the order given
Ÿ:
1. Park the vehicle a safe distance from traffic and on suitable ground.
2. Connect the electronic parking brake Ÿpage 210.
3. Turn the light switch to position 0 Ÿpage 113.
4. Move the gear lever into the neutral position Ÿpage 113.
5. Automatic gearbox: Move selector lever to position P Ÿpage 201.
6. Stop the engine and remove the key from the ignition Ÿpage 195.
7. Manual gearbox: Select a gear Ÿpage 201.
8. Wait until all of the passenger compartment lights are turned off
Ÿpage 113.
9. Allow the corresponding bulb to cool.
10. Visually inspect fuses to see if any are blown Ÿpage 356.
11. Replace the bulb according to the instructions Ÿ. Bulbs should only
be replaced by new identical models. Bulb information is displayed on
the bulb socket or on the bulb itself.
12. In general, never touch the bulb glass directly. The heat of the bulb would
cause the fingerprint to evaporate and condense on the reflector. This
will impair the brightness of the headlight.
lights upPossible causeSolution
A vehicle exterior lighting
bulb is not working.Replace the faulty bulb.
Page 376 of 413

If and when375
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Towing and tow starting
Introduction
When towing, always respect legal requirements.
For technical reasons, it is not possible to tow a vehicle if the battery is flat.
Additional information and warnings:
xElectronic power control and exhaust gases purification system
Ÿpage 255
WARNING
A vehicle with a flat battery should never be towed.
xNever remove the key from the ignition lock. The electronic steering
lock could engage. Then the vehicle will be uncontrollable. You may lose
control of the vehicle and there is a risk of serious accident.
WARNING
When towing the vehicle, the handling and braking efficiency change
considerably. Please observe the following instructions to minimise the
risk of serious accidents and injury:
xAs the driver of the vehicle being towed:
The brake must be depressed must harder as the brake servo does
not operate. Always remain aware to avoid collision with the towing
vehicle.
More strength is required at the steering wheel as the power
steering does not operate when the engine is switched off.
xAs the driver of the towing vehicle:
Accelerate gently and carefully. Avoid sudden braking and manoeuvres.
Brake well in advance than usual and brake gently.
Caution
xCarefully fit and remove the towing ring and its cover to avoid damage to
the vehicle (for example, paintwork).
xWhen towing, fuel could enter the catalytic converter and cause
damage!
Instructions for tow starting
In general, the vehicle should not be started by towing. Jump-starting is
much more preferable Ÿpage 371.
For technical reasons, the following vehicles can not be tow started:
xVehicles with an automatic gearbox.
xVehicles with the KESSY locking and ignition system, given that the elec-
tronic steering lock will certainly not be unlocked.
xVehicles with an electronic parking brake, given that it is possible that the
brake will not be disengaged.
xIf the vehicle battery is flat, it is possible that the engine control units do
not operate correctly.
However, if your vehicle must absolutely be tow-started (manual gearbox):
xEngage 2nd or 3rd gear.
xKeep the clutch pressed down.
xSwitch on the ignition and the hazard warning lights.
xRelease the clutch when both vehicles are moving.
WARNING (continued)