warning light Seat Alhambra 2010 Owner's Guide

Lights and visibility 128
Rain sensor*
The rain sensor controls the frequency of the windscreen wiper intervals,
depending on the amount of rain Ÿ. The sensitivity of the rain sensor can
be adjusted manually. Manual wipe Ÿpage 125Move the lever to the required position Ÿfig. 75:
Rain sensor off.
Rain sensor on; automatic wipe if necessary.
Setting sensitivity level of rain sensor
Set control to the right: highly sensitive.
Set control to the left: less sensitive.
When the ignition is switched off and then back on, the rain sensor stays on
and starts operating again when the windscreen wipers are in position
and the vehicle is travelling at more than 4 km/h (2 mph).
Rain sensor modified behaviour
Possible causes of faults and mistaken readings on the sensitive surface
Ÿfig. 76 of the rain sensor include:
xDamaged blades: A film of water on the damaged blades may lengthen
the activation time, reduce the washing intervals or result in a fast and contin-
uous wipe.
xInsects: insects on the sensor may trigger the windscreen wipers.
xSalt on roads: in winter, salt spread in the roads may cause an extra long
wipe when the windscreen is almost dry.
xDirt: dry dust, wax, coating on glass (Lotus effect) or traces of detergent
(car wash) may reduce the effectiveness of the rain sensor or make it react
more slowly, later or not at all.
xCracked windscreen: the impact of a stone will trigger a single wipe cycle
with the rain sensor on. Next the rain sensor detects the reduction in the
sensitive surface area and adapts accordingly. The behaviour of the sensor
will vary with the size of the damage caused by the stone.
WARNING
The rain sensor may not detect enough rain to switch on the wipers.
xIf necessary, switch on the wipers manually when water on the wind-
screen obstructs visibility.
Fig. 75 Windscreen wiper
lever: adjusting the rain
sensor .
AA
Fig. 76 Rain sensor
sensitive surface.
A0
A1
AA
A1

Lights and visibility129
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
Clean the sensitive surface of the rain sensor regularly and check the blades
for damage Ÿpage 128, fig. 76 (arrow).
Note
To remove wax and coatings, we recommend a window cleaner containing
alcohol.
Checking and topping up the windscreen washer bottle with
water
Check the water level in the windscreen washer bottle regularly and top up as
required.
xOpen the bonnet ’ Ÿpage 304.
xThe washer bottle is marked with the symbol Y on the lid Ÿfig. 77.
xCheck there is enough water in the bottle.
xTo top up, mix water with a window cleaner recommended by SEAT Ÿ.
Please follow the instructions for use found on the packaging.
xIn cold weather, a special antifreeze should also be added to prevent the
water from freezing Ÿ.
Bottle capacity
The bottle holds approximately 3.0 litres; in vehicles with headlight washer,
it is approximately 7.0 litres.
WARNING
Never mix an unsuitable antifreeze or other similar products with the wind-
screen washer water. A greasy layer may be formed on the windscreen
which will impair visibility.
xUse clean water with a window cleaner recommended by SEAT.
xIf necessary, add a suitable antifreeze to the water bottle.
Caution
xDo not mix cleaning products recommended by SEAT with other products.
This could lead to flocculation and may block the windscreen washer jets.
xWhen topping up service fluids, make absolutely certain that you fill the
fluids into the correct reservoirs. Failure to observe this point will result in
serious malfunctions and engine damage!
Fig. 77 In the engine
compartment: windscreen
washer bottle top.

Lights and visibility 130
Rear vision mirror
Introduction
Additional information and warnings:
xPersonal convenience settings in the SEAT information system Ÿpage 70
xSeat memory Ÿpage 137
xChanging gear Ÿpage 201
xBraking, stopping and parking Ÿpage 210
WARNING
The automatic anti-dazzle rear vision mirror contains an electrolytic fluid
which may leak if the mirror is broken. This fluid can cause irritation to the
skin, eyes and respiratory organs.
xThe electrolytic fluid may cause irritation to the skin, eyes and respira-
tory organs, particularly in individuals suffering from asthma or other
illnesses. Make sure that adequate quantities of fresh air enter and leave
the vehicle if it is not possible to open all the doors and windows.
xIf the electrolytic fluid comes into contact with eyes or skin, wash the
area for at least 15 minutes with plenty of water, and seek medical advice.
xIf the electrolytic fluid comes into contact with shoes or clothing, wash
the area for at least 15 minutes with plenty of water. Wash shoes and
clothing before wearing them again.
xIf the electrolytic fluid is swallowed, wash the mouth with plenty of
water for at least 15 minutes. Do not try to provoke vomiting unless recom-
mended by a Doctor. Seek medical advice immediately.
Caution
If an automatic anti-dazzle rear vision mirror is broken, the electrolytic fluid
may leak out. This fluid attacks plastic surfaces. Therefore, it should be
cleaned as fast as possible with a damp sponge or similar.

Lights and visibility131
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Rear vision mirror
The driver should always adjust the rear vision mirror to permit adequate visi-
bility through the rear window.Manual anti-dazzle function for rear vision mirror
xBasic position: point the lever at the bottom of the mirror forwards.
xPull the lever to the back to select the anti-dazzle function Ÿfig. 78.
Automatic anti-dazzle function for interior mirror
Legend for the fig. 79:
warning lamp
Control
Light incidence sensor
This function can be activated and deactivated by pressing the rear vision
mirror switch Ÿfig. 79 . When it is activated, the warning lamp lights up
.
When the ignition is on, the sensor automatically moves the rear vision
mirror to the anti-dazzle position depending upon the incidence of the light
from behind.
The automatic anti-dazzle function is deactivated when reverse gear is
engaged or the interior or reading lights are on.
Note
If the incidence of the light on the sensor is obstructed or prevented, e.g. by
the sun blinds, the rear vision mirror with automatic anti-dazzle function will
not operate correctly.
Fig. 78 Manual anti-
dazzle function for rear
vision mirror
Fig. 79 Automatic anti-
dazzle function for rear
vision mirror
A1
A2
A3
A2A1
A3

Lights and visibility133
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
Fold and unfold the exterior mirror, taking care to avoid injuries.
xOnly fold or unfold the exterior mirror when there is no-one in the way
of the mirror.
xWhen moving the mirror, take care not to trap fingers between the
mirror and the mirror bracket.
WARNING
Failure to correctly estimate the distance of the vehicle behind could lead
to serious accident.
xRear-view convex or aspheric mirrors increase the field of vision,
however objects appear smaller and further away in the mirrors.
xThe use of these mirrors to estimate the distance to the next vehicle
when changing lane is imprecise and could result in serious accident.
xIf possible, use the rear vision mirror to estimate distances to vehicles
behind you or in other circumstances.
xMake sure that the rear visibility is adequate.
Caution
xBefore entering a car wash, always ensure that the exterior mirrors are
correctly folded in.
xElectrically-folding exterior mirrors should not be folded and unfolded
mechanically as this may damage the electrical operation.
For the sake of the environment
The exterior mirror heating should be switched off when it is no longer
needed. Otherwise, it is an unnecessary fuel waste.
Note
The exterior mirror heating initially heats up with a high power, after two
minutes the heat will depend upon the ambient temperature.
Note
In the event of faults, the electric exterior mirrors can be adjusted manually
by pressing the edge of the mirror surface.

Seats and storage compartments137
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Seat functions
Introduction
Additional information and warnings
xAdjust the seat position Ÿpage 10
xSeat belts Ÿpage 22
xAirbag system Ÿpage 33
xChild seats (accessories) Ÿpage 42
xIntegrated child seats Ÿpage 52
xExterior mirrors Ÿpage 130
xLuggage compartment Ÿpage 146
WARNING
Inappropriate use of the seat functions can cause severe injuries.
xAssume the proper sitting position before your trip and remain in it
throughout. This also applies to the other occupants.
xOnly adjust the seat position memory when the vehicle is stationary.
xOnly switch the lumbar massage function on and off when the vehicle
is stationary.
xKeep hands, fingers, feet and other limbs away from the seat operating
and adjustment radius.
Seat heating
The seat cushions can be heated electrically when the ignition is switch on.
The backrest is also heated in some versions.
Switch off seat heating if there is nobody in the seat.
WARNING
People whose pain and temperature threshold has been affected by some
kind of medicine, paraplegia or chronic illness (e.g. diabetes) may sustain
FunctionAction Ÿfig. 85
To switch system on:Press button A. Seat heating is switched on fully.
Adjusting the heating
output:Keep pressing button A until the required inten-
sity is set.
The system switches
off:Keep pressing button A until all of the lights are
switched off Ÿfig. 85.
Fig. 85 Detailed view of
the centre console: front
seat heating controls,
here with the second
temperature level set.

Seats and storage compartments 142
The front passenger's frontal airbag must be disconnected Ÿpage 33 if
objects are being transported on the folded front passenger's seat.
Folding the backrest of the front passenger's seat
xRemove any objects from the front passenger's seat cushion Ÿ.
xAdjust the front passenger's seat to its lowest position Ÿpage 10.
xPush the head restraint down as far as it will go Ÿpage 10.
xUnlock the backrest of the front passenger's seat in the direction of the
arrow Ÿpage 141, fig. 88 .
xFold the backrest of the front passenger's seat forwards in the direction of
the arrow Ÿpage 141, fig. 88 until it is horizontal.
xThe backrest of the front passenger's seat must engage safely in its folded
position.
Lifting the backrest of the front passenger seat
xCheck that there are no objects or parts of the body in the hinge area.
xLift the backrest of the front passenger's seat by first unlocking it again
Ÿpage 141, fig. 89.
xLift the backrest of the front passenger seat until it is upright. The backrest
must be engaged.
xThe upright backrest of the front passenger's seat must safely engage.
WARNING
Folding and lifting the backrest of the front passenger's seat uncontrol-
lably or without paying attention may lead to severe injuries.
xOnly fold and lift the backrest of the front passenger's seat when the
vehicle is stationary.
xWhile the backrest of the front passenger's seat is folded, the frontal
airbag must remain disconnected and the PASSENGER AIRBAG OFF  light
on.
xKeep your hands, fingers, feet and other body parts out of the hinges
and the seat locking mechanism when folding and unfolding.
xMats or other objects can be caught in the hinges of the backrest of the
front passenger's seat. This could prevent the backrest from locking safely
when positioned upright.
xThe upright backrest of the front passenger's seat must engage. If the
backrest of the front passenger's seat is not locked, it may suddenly move
and cause severe injuries.
WARNING
Seat anchors and hinges exposed when the backrest of the front
passenger's seat is folded may lead to severe injuries in the event of an
accident or sudden braking.
xNever carry people or children on the front passenger's seat when the
backrest is folded.
xWhen the backrest of the front passenger's seat is folded, only the
outer seat behind the driver on the second row of seats may be occupied.
This also applies to children sitting in a child seat.
A1
A2
WARNING (continued)

Seats and storage compartments 146
Loading luggage compartment
Introduction
Always transport heavy loads in the trunk and place the seat backs in a
vertical position. Always use the fastening rings with suitable rope or straps.
Never overload the vehicle. Both the carrying capacity as well as the distribu-
tion of the load in the vehicle have effects on the driving behaviour and
braking ability Ÿ.
Additional information and warnings:
xAirbag system Ÿpage 33
xLight Ÿpage 113
xTranspor ting Ÿpage 13
xTo wi ng m o d e Ÿpage 260
xWheels and tyres Ÿpage 323
WARNING
When the vehicle is not in use or being watched, always lock the doors and
the tailgate to reduce the risk of serious injury or death.
xDo not leave children unwatched, especially when the tailgate is open.
Children could climb into the luggage compartment, close the tailgate from
inside and be unable to escape themselves. This could lead to serious
injury or death.
xNever allow children to play in or around the vehicle.
xNever transport people in the luggage compartment.
WARNING
Unsecured or incorrectly secured objects can cause serious injury in case
of a sudden manoeuvring or breaking or in case of an accident. This is espe-cially true when objects are struck by a detonating airbag and fired through
the vehicle interior. To reduce the risks, please note the following:
xSecure all objects in the vehicle. Always keep equipment and heavy
objects in the luggage compartment.
xAlways secure objects with suitable rope or straps so that they cannot
enter the areas around the frontal or side airbags in case of sudden braking
or an accident.
xWhile driving, always keep object compartments closed.
xDo not place hard, heavy or sharp objects inside the passenger
compartment, in open storage compartments, the rear shelf or on the
dashboard.
xRemove hard, heavy and sharp objects from clothes and pockets inside
the vehicle and store securely.
WARNING
The transport of heavy object changes vehicle handling and increases
braking distance. Heavy loads that have not been stored or secured
correctly could cause loss of control and result in serious injury.
xThe vehicle handling changes when transporting heavy objects due to
a change in the centre of gravity.
xDistribute the load as uniformly and as low down on the vehicle as
possible.
xStore heavy objects in the luggage compartment as far from the rear
axle as possible.
Caution
xHard objects on the shelf could chafe the wires of the heating element
and antenna of the rear window and cause damage.
xThe side window antenna could be damaged due to chafing from objects.
WARNING (continued)

Seats and storage compartments 154
xSecure all objects, little and large.
xNever secure a load that is too heavy for the fastening rings.
xNever secure a child seat to the fastening rings.
Note
The maximum load of the fastening rings is approximately 3.5 Kn (3.57 Kp).
Note
You can find suitable transport straps and load securing systems at a
specialist workshop. SEAT recommends visiting a qualified workshop.
Rails and attachment system*
The rails and attachment system consists of four rails, movable attachment
elements, straps to be secured to the rails and a net with supports to cover
baggage Ÿpage 155. The rail and attachment system is designed to secure
light objects. If the seats in the third row are to be occupied by passengers
then attachment elements should never be placed in the section of the rails
close to the seats Ÿ.
Installing the attachment elements
xFit the attachment element with the ruts facing upwards Ÿfig. 102 to
the upper part of the guide and press downwards.
xMove the attachment element to the desired position.
xAlways ensure that the attachment inserts into the guide system Ÿ.
Removing the attachment elements
xRemove the attachment element from the guide and pull downwards.
Securing a load
xPull the strap through the attachment element and secure the load Ÿ.
WARNING
In case of an accident or sudden braking, the attachment elements in the
parts of the rails close to the seats of the third row could injure seat occu-
pants.
xWhenever the seats on the third row are to be occupied, remove the
attachment elements from the rails or move them all the way back.
WARNING
Movable attachment elements that are not secured correctly can be
released from the guide in case of sudden braking or accident. As a result,
objects may be fired through the passenger compartment causing serious
injury or death.
WARNING (continued)
Fig. 102 In the luggage
compartment: System
including rails, adjustable
attachment elements
and adjustable tightening
straps .
A1
A2
A1

Seats and storage compartments157
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
Baggage net supports that are not secured correctly can be released from
the guide in case of the sudden braking or accident. As a result, objects
may be fired through the passenger compartment causing serious injury or
death.
xAlways ensure that the baggage net supports are correctly inserted into
the rails; the red mark should not be visible.
xNever secure a child seat to the baggage net supports.
Caution
xThe baggage net supports placed on the rail system can be damaged
when folding down seats from the third row or putting them back into posi-
tion and these can also damage the seats themselves. Before folding down
or repositioning the seats, remove the baggage net supports from the rail
system.
Retaining hooks
On the right-hand side of the luggage compartment, there are folding
retaining hooks Ÿfig. 105 that can be used to secure light shopping bags.
xPress the retaining hooks down Ÿfig. 105 (arrow) and fold them.
xHook the bags in place.
xAfter use, raise the hooks again.
WARNING
Never use these hooks to secure objects. In case of sudden braking or an
accident, the hooks could rupture.
Caution
The hooks can support a maximum of 2.5 kg (about 5 lbs).
Fig. 105 In the luggage
compartment: retaining
hooks.