seats Seat Alhambra 2010 Manual PDF

Seats and storage compartments173
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Ashtray and cigarette lighter*
Introduction
Additional information and warnings:
xSockets Ÿpage 175.
xAccessories, parts replacement, repairs and modifications Ÿpage 285.
WARNING
Undue use of the ashtray and cigarette lighter may cause a fire or burns and
other serious injuries.
xNever put paper or other flammable objects in the ashtray.
Ashtray
There are ashtrays located on the front of the centre console Ÿfig. 124 and
on the rear lining of the back door.
Opening and closing the ashtray
xTo open, lift the ashtray cover.
xTo close, push the ashtray cover down.
Emptying the ashtray
xRemove the ashtray from the cup holder or lining of the door by pulling it
upwards.
xAfter emptying the ashtray, insert it from above into the cup holder or door
lining.
Cigarette lighter
Depending on the vehicle equipment, there may be a lighter to the front of the
centre console Ÿfig. 125 or in the compartment to the front of the centre
console.Fig. 124 Front centre
console: ashtray closed.
Fig. 125 Front centre
console: lighter.

Seats and storage compartments 174
xPush the button on the cigarette lighter inwards with the ignition on
Ÿpage 173, fig. 125.
xWait for the cigarette lighter to pop out slightly.
xPull out the cigarette lighter and light the cigarette on the glowing coil
Ÿ.
xReplace the cigarette lighter in its insert.
WARNING
Undue use of the cigarette lighter may cause a fire or burns and other
serious injuries.
xThe cigarette lighter must only be used to light cigarettes or similar.
xNever leave children unsupervised in the vehicle. The cigarette lighter
can be used when the ignition is switched on.
Note
The cigarette lighter can also be used with the 12 Volt socket Ÿpage 175.

Seats and storage compartments175
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Sockets
Introduction
Electrical equipment can be connected to the sockets in the vehicle.
Connected equipment must be in perfect condition and show no signs of
faults.
Additional information and warnings:
xCigarette lighter Ÿpage 173
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Improper use of the sockets or electrical devices could lead to a fire and
cause serious injuries.
xNever leave children unsupervised in the vehicle. The sockets and
equipment connected to them can be used when the ignition is switched
on.
xShould a connected electrical device overheat, switch it off and unplug
it immediately.
Caution
xTo avoid damage to the vehicle's electrical system, never connect equip-
ment that generates electrical current, such as solar panels or battery
chargers, to the 12 Volt sockets in order to charge the vehicle's battery.
xOnly use accessories with approved electromagnetic compatibility
according to current regulations.
xTo avoid damage due to voltage variations, switch off all appliances
connected to the 12 V sockets before switching the ignition on or off and
before starting the engine.
xNever connect an appliance to the 12 Volt socket that consumes more
than the power indicated in watts. Exceeding the maximum power absorption
could damage the vehicle's electrical system.
For the sake of the environment
Do not leave the engine running when the vehicle is at a standstill.
Note
Using electrical appliances with the engine stopped and the ignition
switched on will drain the battery.
Note
Unshielded equipment can cause interference on the radio equipment and
the vehicle's electrical system.
Note
Interference can occur on the radio's AM waveband if electrical appliances
are used near the rear window aerial.

Seats and storage compartments 176
Vehicle socketsMaximum power consumption
The maximum capacity of each socket must not be exceeded. The power
consumption is indicated on the rating plate of each appliance.
Where two or more appliances are connected at the same time, the total
rating of all the connected devices must never exceed 190 Watts Ÿ.
12 volt socket
The 12 Volt socket will only work with the ignition on.
Using electrical appliances with the engine stopped and the ignition
switched on will drain the battery. Therefore, electrical consumers connected
to the socket must only be used when the engine is running.
To prevent voltage variations from causing damage, switch off the electrical
consumer connected to the 12 Volt socket before switching the ignition on or
off and before starting the engine.
12 Volt sockets can be found in the following locations in the vehicle:
xCompartment in the centre of the centre console.
xCompartment in the front centre console.
xStorage compartment in the front central armrest.
xRear centre console Ÿfig. 126.
xAt the rear right of the luggage compartment.
230 Volt Euro socket*
The socket only works when the engine is running Ÿ.
Connecting an electrical appliance: Plug the appliance into the socket as far
as possible to unlock the built-in child safety device. The current only flows
when the child safety device is unlocked.
Fig. 126 Centre console,
rear section: 12 volt
socket.
Fig. 127 Rear centre
console: 230 Volt Euro
socket.
SocketMaximum power consumption
12 Volts120 Watts
230 Volts150 Watts (300 Watt peak)

Seats and storage compartments177
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Heat protection
The 230 Volt Euro power connector converter switches off automatically when
a certain temperature is exceeded. This disconnect prevents overheating in
the event of an increase in power consumption of the connected appliance
and where the atmospheric temperature is too high. The converter will switch
on again automatically after it has cooled down. Appliances that are switched
on and connected to the socket will start up again. Therefore, switch off all
electrical appliances connected to the socket when the current converter
switches off due to overheating.
WARNING
High voltage in the electrical installation!
xLiquids must not be spilt over the socket.
xDo not plug adapters or extension cords into the 230 Volt Euro power
connector. Otherwise, the built-in child safety device will switch off and the
connector will become live.
xDo not plug current conductors such as a knitting needle into the 230
Volt Euro power connector.
Caution
xAlways follow the operating instructions for the appliances to be
connected!
xNever exceed the maximum power rating as this could damage the
vehicle's general electrical system.
x12 volt socket:
Only use accessories with approved electromagnetic compatibility
according to current regulations.
Never power the socket.
x230 Volt Euro socket:
Do not hang appliances or plugs that are too heavy (e.g. a transformer)
from the socket.
Do not connect lamps which contain a neon tube.
Only plug appliances with a voltage that matches the socket voltage
into the socket.
In the event of consumers with a high start-up current, surge protection
prevents them from switching on. In this case, unplug the consumer and
try plugging it back in after around 10 seconds.
Note
Some appliances may not work properly in the 230 Volt Euro power connector
due to a lack of power (Watts).
Note
The 230 Watt Euro power connector can be modified for 115 Watt appliances
and vice versa. Consult a specialist shop for advice on accessories to adapt
the connector. SEAT recommends visiting a qualified workshop.
LED on the socket Ÿpage 176, fig. 127
Steady green light:The child safety device is unlocked. The
socket can now be used.
Flashing red light:There is some kind of fault (e.g. discon-
nection due to excess current or tempera-
ture).

Seats and storage compartments 178
Toll card reader*
Introduction
With the toll card reader switched on and operational, the price will be auto-
matically charged when the vehicle crosses a toll. A sound will confirm
payment. A voice will inform you of the price to pay, together with an indica-
tion of the location on the navigation system display.
Additional information and warnings:
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Using the toll card reader while the vehicle is in motion may distract you
from the road and lead to accidents.
Description
Starting the toll reader
Switch on the radio navigation system and insert a suitable ETC card into the
toll card reader Ÿfig. 128 (arrow).
A long acoustic signal and the display of the ETC symbol in the status line of
the radio navigation system will indicate that the card is operational.
Removing the toll card
Press the button Ÿfig. 128 to remove the toll card.
Error message
If a short signal is heard after switching the system on, this indicates an error
(e.g. ETC card not inserted or faulty). The toll card reader is not operational.
Fig. 128 In the glove
compartment on the front
passenger side: Toll card
reader.
A1

Heating, Ventilation and Air conditioning 182
Some Climatronic controls may also be on the climate control system control
panel located in the rear centre console. These controls are used to make the
appropriate settings for the rear seats.
Control
button Additional information. Climatic Ÿpage 181, fig. 129; Cli-
matronic Ÿpage 181, fig. 130.
Tem-
perature
ˆ ... ˆ
Climatic: rotate the control to adjust the temperature accord-
ingly.
Climatronic: the settings for the left hand side, the right-hand
side and the rear seats are made separately. Rotate the control
to adjust the temperature accordingly. The temperature is indi-
cated on the outside ring.
Fan
 ... –
Climatic: setting 0, fan and Climatic switched off;
setting 4, fan set to maximum.
Climatronic: the Fan speed is automatically adjusted depend-
ing on the vehicle speed to avoid annoying noises. The fan can
also be adjusted manually.
Air dis-
tributionClimatic: rotate the continuous control to direct the airflow to
the desired area.
Climatronic: manually adjustable using the controls.
<
Climatic: defrost function. The airflow is directed at the wind-
screen. In this position, air recirculation is automatically
switched off or is not switched on.
<
Climatronic: defrost function. The air drawn in from outside the
vehicle is directed at the windscreen and air recirculation is
automatically switched off. To defrost the windscreen more
quickly, the air is dehumidified at temperatures over approxi-
mately +1.5 °C (+35 °F) and the fan runs at maximum output.
KThe air is directed at the chest of driver and passengers by the
dashboard air vents.
L– Air distribution towards the footwell.
A1
A2
A3
qAir distribution towards the windscreen and the footwell.
ACClimatic, Climatronic: Press the button to turn off/on cooling.
=
Heated rear window: this only works when the engine is run-
ning and switches off automatically after a maximum of 10
minutes.
Air recirculation mode Ÿpage 185.
oClimatronic: Automatic air recirculation Ÿpage 185.
pWindscreen heating: only works when the engine is running
and switches off automatically after a few minutes.
>Instant auxiliary heating on/off button Ÿpage 187.
Switching
off
OFFClimatic: turn the fan switch to setting 0.
Climatronic: press the button or set the fan manually to 0.
When the system switches off, the button will light up.
REAR
Climatronic: press the button to adjust the climate con-
trol for the rear seats from the front. The button will light
up when the function is switched on. The settings for the rear
seats will be displayed. Press the button again to switch the
function off or do not touch any other button for around 10
seconds.
Control
button Additional information. Climatic Ÿpage 181, fig. 129; Cli-
matronic Ÿpage 181, fig. 130.
OFF
OFF
REAR
REST

Heating, Ventilation and Air conditioning183
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
Never turn off the air fan for a long time or the air in the passenger compart-
ment will not be refreshed.
xStuffy or used air will increase fatigue and reduce driver and passenger
concentration possibly resulting in a serious accident.
Note
Not all Climatronic buttons are operational in REAR mode.
Note
The button is locked in defrost mode.
Climate control user instructions
The cooling system only works when the engine is running and fan is
switched on.
The climate control system operates most effectively with the windows and
the sliding panoramic roof closed. However, if the vehicle has heated up after
standing in the sun for some time, the air inside can be cooled more quickly
by opening the windows briefly.
Keep the air vents in front of the windscreen free of snow, ice and leaves to
ensure heating and cooling are not impaired and to prevent the windows
from misting over.
Adjustment for safer driving
When the air conditioning is switched on, the temperature and the air
humidity in the vehicle interior drop. Hence, when the outside air humidity is
high, the windows do not mist over and comfort for the vehicle occupants is
improved:
With Climatic
xDisable air recirculation mode Ÿpage 185.
xSet the fan to setting 1 or 2.
xTurn the temperature control to the centre position.
xOpen the air outlets in the dash panel Ÿpage 185.
xTurn the air distribution control to the required position.
xPress the button to turn on cooling. The button will light up.
With Climatronic
xPress the button.
xSet the temperature to +22 °C (+72 °F).
xOpen the air outlets in the dash panel Ÿpage 185.
REST
Climatronic: press the button to use residual heat. When
the engine is still warm but the ignition switched off, the heat
given off by the engine can be used to keep the passenger
compartment warm. The button will light up when the
function is switched on. The function will switch off after
around 30 minutes and if the battery level is low.
p
Climatronic: transferring the driver's seat temperature settings
to the other seats. If the button is not lit up, the set tem-
perature in the driver's seat will also apply to the other seats.
Press the button or the temperature control for the front pas-
senger's seat or the rear seats to set them to a different tem-
perature. The button lights with an indicator.
Vehicles with auxiliary heating: observe the description of the
button.
AUTOAutomatic temperature, fan, and air distribution control.
Control
button Additional information. Climatic Ÿpage 181, fig. 129; Cli-
matronic Ÿpage 181, fig. 130.
REST
REST
p
AUTO
REAR
AC
AUTO

Driving and the environment253
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Some equipment, when connected, increase fuel consumption considerably,
for example:
xAir conditioning cooling system: If the air conditioning system is required
to cool to significantly lower temperatures than the true outside temperature,
it will require a large quantity of energy from the engine. Therefore, we recom-
mend that the selected temperature for the vehicle is not too different to the
outside temperature. It is a good idea to open all the windows of the car
before starting your journey, and to drive a short distance with all the
windows open to allow the vehicle to cool down slightly. Only then should
you close all the windows and switch on the air conditioning. Keep windows
closed when travelling at high speeds. Driving with the windows open
increases fuel consumption.
xSwitch off the seat heating when the seats have warmed up.
xSwitch off the heated rear window and the windscreen heating when the
windows have demisted and are free of ice.
xDo not leave the independent heating switched on when the vehicle is
moving Ÿpage 187.
Other factors which increase fuel consumption (examples):
xFault in engine management.
xDriving on hills.
xTrailer towing.
Saving fuel while driving
By adopting an economical driving style and anticipating the traffic situation
ahead, you can easily reduce fuel consumption by 10-15%.
A vehicle uses most fuel when accelerating. By anticipating the traffic situa-
tion ahead, you will brake and therefore accelerate less. Wherever possible,
let the car roll slowly to a stop, for instance when you can see that the next
traffic lights are red.
Avoid short journeys
Fuel consumption is much higher when the engine is cold, immediately after
it has been started. It takes a few kilometres of driving for the engine to warm
up and to normalise consumption.
The engine and catalytic converter need to reach their proper working
temperature in order to minimise fuel consumption and emissions. The
ambient temperature has a decisive influence.
fig. 162 shows the difference in consumption for the same journey at +20 °C
(+68 °F) and at -10 °C (+14 °F).
Fig. 162 Fuel consump-
tion in litres per 100 km at
different outside tempera-
tures.

Accessories, parts replacement and modifications287
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a The Technical Service does not accept liability for damage resulting from
technical modifications or repairs performed incorrectly; neither is the SEAT
warranty valid in these cases.
SEAT recommends you have any technical modifications or repairs performed
at a SEAT authorised service and that you use genuine SEAT spare parts
®.
Vehicles with special accessories and equipment
The manufacturers of additional equipment guarantee that the equipment
complies with applicable laws and regulations with respect to the environ-
ment, in particular Directives 2000/53/CE and 2003/11/CE. The first direc-
tive governs the disposal of end-of-life vehicles while the second refers to the
restrictions on the marketing and use of certain dangerous substances and
preparations.
The vehicle owner should keep the documentation for the additional equip-
ment safely and hand it over to the scrap yard at the end of the vehicle's
service life. This ensures that any additional equipment mounted in end-of-
life vehicles is correctly disposed of with respect for the environment.
WARNING
Repairs or modifications which are not performed correctly may result in
damage or errors in the vehicle operation, affecting the efficiency of the
driver assist systems. This could result in serious accident.
xAll repairs and modifications to the vehicle should only be performed
by a qualified workshop.
Repair and faults in the airbag system
When performing repairs and technical modifications, SEAT's directives
must be observed! ŸModifications and repairs to the front bumper, doors, front seats, and repairs
to the roof or chassis should only be carried out in a qualified workshop.
These components may contain parts or sensors belonging to the airbag
system.
If work is carried out on the airbag system or remove and fit parts of the
system when performing other repair work, parts of the airbag system may be
damaged. The consequence may be that, in the event of an accident, the
airbag inflates incorrectly or does not inflate at all.
So that the effectiveness of the airbag is not reduced and that removed parts
do not cause any injuries or environmental pollution, regulations must be
observed. These requirements are known to qualified dealerships.
Modifications to the vehicle suspension may affect the operation of the
airbag system in the event of collision. For example, if wheel and tyre combi-
nations not approved by SEAT are used, or if the vehicle height is lowered, the
suspension is stiffened or the suspension springs, telescopic arms, dampers,
etc., are modified, the results received by the airbag sensors and sent to the
control unit may not be accurate. For example, some modifications to the
suspension could increase the force measured by the sensors and result in
the triggering of the airbag systems in collisions. Under normal conditions,
the measured values would be lower and the airbag would not have been trig-
gered. Other modifications may reduce the forces measured by the sensors
and therefore the airbags are not triggered in situations when they should
have triggered.
WARNING
Repairs or modifications which are not performed correctly may result in
damage or errors in the vehicle operation, affecting the efficiency of the
airbag systems. This could result in serious or fatal accident.
xAll repairs and modifications to the vehicle should only be performed
by a qualified workshop.
xAirbag modules must never be repaired: if damaged, they must be
replaced.