turn signal Seat Alhambra 2010 Owner's Manual

Safe driving 8
xCheck that the lights and turn signals operate correctly.
xCheck the tyre pressures (Ÿpage 323) and level of fuel (Ÿpage 293).
xEnsure there is good visibility through all the windows.
xMake sure that all objects and bags in the storage compartments, in the
luggage compartment and, where applicable, on the roof, are securely
fastened Ÿpage 13.
xEnsure there is nothing obstructing the free passage of the foot pedals.
xUse child retention systems appropriate for the child's body weight and
height Ÿpage 42.
xCorrectly adjust front seat, head rests and rear-view mirrors to suit your
height Ÿpage 10.
xWear close-fitting shoes which do not prevent you from using the pedals
correctly.
xThe driver's floor mat should be fixed to the floor, leaving the pedal area
unobstructed.
xBefore starting out, ensure you are correctly seated and remain in this
position throughout the journey. This applies to all passengers in the vehicle
Ÿpage 10.
xCorrectly fasten your seat belt before starting to drive and keep it securely
fastened throughout the journey. This applies to all passengers in the vehicle
Ÿpage 22.
xNever carry more passengers than the number of available seats and seat
belts in your vehicle.
xNever drive with impaired faculties (for example, due to medication,
alcohol or drugs).
xDo not allow yourself to be distracted from the traffic, for example, to reset
or switch on a menu, by other passengers or to answer a phone call.
xAlways try to adapt the speed of the vehicle and your style of driving to the
condition of the ground or the road and to weather and traffic conditions.
xObserve the highway code and speed limits.
xOn long journeys, rest at regular intervals (at least every two hours).
xIf carrying animals, make sure they are correctly restrained in accordance
with their weight and size.
WARNING
Always observe traffic regulations and speed limits and try to anticipate
traffic movements. Correctly anticipating traffic situations may mean the
difference between arriving safe and sound at your destination or having a
serious accident.
Note
Regular servicing of your vehicle not only helps to keep it in good working
order but also helps to ensure road safety. Therefore, please ensure the
vehicle is taken for service as indicated in the Maintenance Programme. If the
vehicle is subjected to hard use, it may require certain maintenance work
before the next service date. Hard use may involve frequent driving in traffic
jams, driving in dusty areas or frequent use of the tow-bar. For further infor-
mation, please refer to a SEAT dealer or specialised workshop.
Driving abroad
Check list
In some countries, certain safety regulations and requirements are in force
relating to exhaust gas emissions, which differ from the technical character-
istics of the vehicle. Before travelling abroad, SEAT recommends you consult
a SEAT dealer about the legal requirements and the following points:
xDoes the vehicle need technical modifications for driving abroad, for
example, adjustment of the headlamps?
xDoes the vehicle have all the tools, diagnostics equipment and spare
parts required for inspections and repairs?
xAre there any SEAT dealers in the destination country?

Cockpit59
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Operating instructions
Cockpit
Overview
Overview of the dash panel
This overview will help you to familiarise yourself with the
controls and displays.
Door release lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Central locking button 0 1. . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch for adjusting the exterior mirrors . . . . . . . . . . . . . . . . .
Exterior mirror adjustment , 2 
Heated exterior mirrors ?
Folding exterior mirrors #
Instrument panel controls and lighting control  . . . . . . . . .
Headlamp range adjustment . . . . . . . . . . . . . . . . . . . . . . . .
Light switch “. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light off --
Automatic headlight control -!54/-
Side/dipped lights  
Fog lights

Controls on the multi-function steering wheel . . . . . . . . . . . .
Volume control for radio, navigation system and phone
conversations & – '
Radio mute or voice control activation Activate telephone main menu or accept an incoming
call -
SEAT information system control buttons ƒ, „, OK, E
Lever for . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main beam headlights 
Headlight flasher 
Turn signals 
Parking lights 
Instrument panel:
Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Horn (works only when the ignition is on)/Front driver airbag
Windscreen wiper/ windscreen wash lever . . . . . . . . . . . . . . .
Windscreen wipers ()'( – ,/7
Intermittent wipe
u
“Brief wipe” x
Windscreen wipers U
Automatic windscreen wash/wipe W
Rear window wiper Z
Automatic rear window wash/wipe \
Lever with buttons for controlling the SEAT information
system 42)0- , /+/2%3%4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Left seat heating controls A. . . . . . . . . . . . . . . . . . . . . . . . . . .
A192
A283
A3130
A4113
A5113
A6113
A770
A8113
A9
64
64
61
A1033
A11124
70
A12137

Cockpit 62
Green symbols
Blue symbols
Colourless symbols
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
lights: Driving light totally or partially faulty.Ÿpage 360
flashes: Fault in the adaptive light system.Ÿpage 113
BFault in catalytic converter.
Ÿpage 255Dlights: pre-ignition of diesel engine.
flashes: Fault in engine management.
%0#Fault in engine management.
¬Diesel particulate filter blocked
DFault in the steering system.Ÿpage 192
~Tyre pressure too low.Ÿpage 323
Fault in the tyre pressure gauge.Ÿpage 245
YLevel of windscreen washer fluid too low.Ÿpage 124
Fuel tank almost empty.Ÿpage 293
Eflashes: Engine oil sensor faulty.Ÿpage 309lights: Insufficient engine oil.
TFault in airbag system and seat belt tensioners.Ÿpage 33
/&&

Passenger front airbag is off (PASSENGER
AIRBAG
/&& ).Ÿpage 33
bTop up "AdBlue", or there is a fault in the "AdB-
lue" system.Ÿpage 300
§Fuel tank not closed correctly.Ÿpage 293
SymbolMeaning ŸSee

Left or right turn signal.Ÿpage 113
Hazard warning lights on.Ÿpage 345
KUse the foot brake!
Change
Ÿpage 201
Brake
Ÿpage 210
%Cruise control operating.Ÿpage 239
SymbolMeaning ŸSee
Headlight on or flasher on.
Ÿpage 113
+Headlight adjustment (Light Assist) on.
SymbolMeaning ŸSee
3!&%Electronic immobiliser active.Ÿpage 195
>Service interval displayŸpage 68

Unlocking and locking89
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a When does the system trigger an alarm?
The anti-theft alarm siren will be triggered for about 30 seconds accompa-
nied by optical warning signals for about five minutes when the vehicle is
locked and the following unauthorised actions are taken:
xWhen the door is mechanically unlocked using the vehicle key without
turning the ignition within the following 15 seconds.
xA door is opened.
xThe bonnet is opened.
xThe tailgate is opened.
xWhen the ignition is switched on with a non-authorised key.
xWhen the vehicle battery is disconnected.
xWhen there is movement inside the vehicle (vehicles with interior moni-
toring).
xWhen the vehicle is towed (vehicles with anti-tow system)
xWhen the vehicle is lifted (vehicles with anti-tow system).
xTransporting the vehicle on a ferry or by railroad (vehicles with an anti-tow
system or passenger compartment monitoring).
xUnhitch a trailer connected to the antitheft alarm Ÿpage 260.
How to turn OFF the alarm
Unlock the vehicle with the unlocking button on the key or turn on the ignition
with a valid key.
Note
The alarm will be triggered once more when anybody enters the same zone of
surveillance or any other zone. If, for example, after opening a door, the tail-
gate is also opened.
Note
The antitheft alarm is not activated when the vehicle is locked from within
using the central locking button .
Note
If the driver's door is unlocked mechanically with the key, only the driver's
door is unlocked, the rest of the doors remain locked. Only when the ignition
has been turned on will the other doors be available - but not unlocked - and
the central locking button activated.
Note
If the vehicle battery is run down or flat then the antitheft alarm will not
operate correctly.
1

Lights and visibility 114
Warning lamps
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
xPark the vehicle at a suitable distance away from the traffic ensuring
that the exhaust system is not in contact with inflammable material, for
example, dry grass, fuel, oil, etc.
xA faulty vehicle represents a risk of accident for the driver and for other
road users. If necessary, switch on the hazard warning lamps and put out
the warning triangle to advise other drivers.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
lights upPossible causeSolution

Driving light totally or partially
faulty.
Replace the corresponding
bulb Ÿpage 360.
If all the bulbs are OK, the vehi-
cle should be taken to a spe-
cialised workshop if necessary.
Fault in adaptive light.Ÿpage 118.

Rear fog light switched on.
Ÿpage 116.
Fog lights switched on

Left or right turn signal.
The warning lamp flashes twice
as fast when a vehicle or trailer
turn signal is faulty.If necessary, check the vehicle
and trailer lighting.
Headlight on or flasher on.Ÿpage 115.
+Headlight adjustment (Light
Assist) on.Ÿpage 117.
flashesPossible causeSolution
Fault in the adaptive light sys-
tem.Contact a specialist workshop
Ÿpage 117.

Lights and visibility115
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Turn signal and main beam lever
Move the lever to the required position:
Right turn signal. Right-hand parking light (ignition switched off)
Ÿpage 117.
Left turn signal. Left-hand parking light (ignition switched off)
Ÿpage 117.
Main beam switched on Ÿ. The indicator lamp
 will light up on the
instrument panel.
Flashing the headlamps. The flashed beam comes on if the lever is
pressed. The indicator lamp
 will light up.
Push the lever all the way down to turn off the corresponding function.
Convenience indicators
For the convenience turn signals, move the lever as far as possible upwards
or downwards and release the lever. The turn signal will flash three times.
The control turn signals are switched on and off from the menu Lights&
Visibility on the instrument panel display Ÿpage 70. This function can be disconnected at a specialised workshop for those vehicles which do not have
the menu Lights & Visibility.
WARNING
Incorrect use of the headlamps may cause accidents and serious injury, as
the main beam may distract or dazzle other drivers.
Note
The turn signal only works when the ignition is switched on. The hazard
warning lights also work when the ignition is switched off Ÿpage 345.
Note
If a turn signal on the vehicle or trailer is faulty, the warning lamp flashes
twice as fast as usual.
Note
The main beam headlights can only be switched on if the dipped beam head-
lights are already on.
Fig. 66 Turn signal and
main beam lever.
A1
A2
A3
A4

Lights and visibility117
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xSwitching on the fog lights : Turn the switch to position  or pull out  to the first stop.
xSwitching on the rear fog light
: turn the light switch to position  o
pull out  to the maximum.
xTo switch off the fog lights, press the light switch or turn it to position /.
Audible warnings to advise the driver that the lights have not been switched
off
If the key is not in the ignition and the driver's door is open, an audible
warning signal is heard in the following cases: This is a reminder to turn off
the lights.
xWhen the parking light is on Ÿpage 115.
xWhen the light switch is in position .
WARNING
The side lights or daytime driving lights are not bright enough to illuminate
the road ahead and to ensure that other road users are able to see you.
xAlways use your dipped beam head lights if it is raining or if visibility is
poor.
Lights and visibility: functions
Parking light
When the parking light is switched on,(right or left turn signal), the front side
light and the rear light on the corresponding side of the vehicle stay lit. The
parking lights will only work with the ignition off.
Daytime driving light
The daytime driving light consists of individual lights in the front headlamps.When the daytime driving light is switched on, only the individual lights come
on Ÿ.
The daytime lights are switched on each time the ignition is turned on if the
light switch is in position
!, 5,4 or /.
When the light switch is in position
!, 5, 4 or /, a photo sensor goes out and
the instrument and switch lighting comes on automatically.
Automatic dipped beam control
!54/
The automatic dipped beam control is merely intended as an aid and is not
able to recognise all driving situations.
When the light switch is in position
!, 5, 4 or /, the vehicle lights and the
instrument panel and switch lighting switch on and off automatically in the
following situations Ÿ:
Activating the daytime lightsDeactivating the daytime lights
Press and hold the turn signal and
main beam lever upwards and back-
wards (right turn signal and light
flasher).Press and hold the turn signal and
main beam lever downwards and
backwards (left turn signal and light
flasher).
Switch the ignition on and off for approximately 3 seconds.
Automatic switching on:Automatic switching off or switch to
daytime lighting:
The photo sensor detects darkness,
for example, when driving through a
tunnel.When adequate lighting is detected.
When driving at more than 140 km/h
for a few seconds.When driving at less than 65 km/h
for a few minutes.
The rain sensor detects rain and acti-
vates the windscreen wipers.When the windscreen wiper has
been inactive for a few minutes.

Lights and visibility 118
Adaptive front lighting system (AFS)
The adaptive headlights only operate when the dipped beam is on and at
speeds of over 10 km/h. When taking a bend, the adaptive headlights auto-
matically light up the road better.
The adaptive headlights can be switched on and off from the infotainment
system.
Static turning lights
When turning slowly to change direction or going round a tight bend, the
static cornering lights automatically come on. The static cornering lights only
work at speeds of less than 40 km/h.
The static cornering lights may be incorporated into the fog lights or the front
headlights, depending upon the equipment.
Main beam headlight control
The main beam control (Light Assist) automatically switches the main beam
on and off within the limits of the system, regardless of prevailing conditions,
traffic and vehicle speed Ÿ. The system is controlled by a sensor on the
inside of the windscreen above the rear view mirror. The main beam and
flashed headlight can be switched on and off manually at the turn signal and
main beam lever.
xTo light, with the ignition on, rotate the headlight control to the posi-
tion!54/ and move the turn signal lever to the full beam headlight position.
When the ignition is switched off, the main beam control is also switched off.
The following conditions may prevent the full beam headlight control from
turning off the headlights in time or from turning off altogether:
xIn poorly lit towns with highly reflective signs.
xIn fog, snow and heavy rain.
xIf the area around the sensor on the windscreen is misted, dirty or covered
with a sticker.
xIf a stone has struck the area of the sensor.
xOther insufficiently lit road users (for example, pedestrians or cyclists).
xOn tight bends and steep slopes and when oncoming vehicles are
partially obscured.
xWhen the drivers of other oncoming vehicles (such as a truck) can see
over a guard rail in the centre of the road.
WARNING
If the road is not well-lit and the vehicle is not clearly visible to other
drivers, there is a risk of accident.
xThe automatic main beam control (!54/) only switches on the dipped
beam when there are no changes in brightness, and not, for example when
it is foggy.
xNever use the daytime driving light if the road is not well-lit as a result
of the weather conditions and poor visibility. The daytime driving lights are
not bright enough to illuminate the road ahead and to ensure that other
road users are able to see you.
xThe rear lights do not come on with the daytime driving light. A vehicle
which does not have the rear lights on may not be visible to other drivers
in the darkness, if it is raining or in conditions of poor visibility.
WARNING
The convenience features of the main beam control should not encourage
the taking of risks. The system is not a replacement for driver awareness.
xAlways check the main beam and adjust it to the traffic, visibility and
light conditions.
xIt is possible that the main beam headlight control does not recognise
all driving situations and is limited under certain circumstances.
xOperation of the main beam headlight control can be affected by
changes made to the vehicle lighting system (for example, if additional
headlights are added).

Lights and visibility119
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
The headlights, rear lights and turn signals may mist up temporarily on the
inside in cool or damp weather. This is normal and in no way effects the useful
life of the vehicle lighting system.
Adhesive strips for headlights or adjusting headlights
In those countries where vehicles drive on the other side of the road to the
home country, the asymmetric dipped beam may dazzle drivers of oncoming
vehicles. Therefore, when driving abroad, adhesive strips should be attached
to the headlights or the headlights should be adjusted accordingly.
The direction of the headlights can be adjusted from the instrument panel, in
the menu Settings submenu Travel mode Ÿpage 70.
For those vehicles in which it is not possible to adjust the headlights from the
menu, adhesive strips are used to cover certain parts of the headlamp cover
or the headlights may be adjusted at a specialised workshop. For further
information, please refer to a specialised workshop. SEAT recommends
visiting a qualified workshop.
Note
The use of Travel mode and adhesive strips on the headlights is only author-
ised for a short period of time. To modify the direction of the headlamps more
permanently, please take the vehicle to a specialised workshop. SEAT recom-
mends visiting a qualified workshop.
Function “Coming home” and “Leaving home” (guidance
lights)
The “Coming home” function should be switched on manually. However the
“Leaving home” function is automatically controlled by a photo sensor.
Lighting around the exterior mirrors
The lighting around the exterior mirrors illuminates the door area on entering
and leaving the vehicles. It comes on when the vehicle is unlocked, when the
vehicle door is opened and when the “Coming home” or “Leaving home”
“Coming Home”Necessary operations
To switch sys-
tem on:
– Switch off the ignition.
– Briefly flash the headlights for approximately one sec-
ond Ÿpage 115.
The “Coming home” lighting comes on when the driver's
door is opened. The delay in switching off the headlights
is counted from when the last door or tailgate is closed.
The system
switches off:
– Automatically at the end of the delay period.
– Automatically, if 30 seconds after coming on, a vehicle
door or tailgate remains open.
– If the light switch is turned to position
/.
– If the ignition is switched on.
“Leaving home”Necessary operations
To switch sys-
tem on:– Unlock the vehicle when the light switch is in position
!54/ and the photo sensor detects darkness.
The system
switches off:
– Automatically, at the end of the delay period.
– When the vehicle is locked.
– When the light switch is turned to position
/.
– When the ignition is switched on.

Lights and visibility 120
function is switched on. If the equipment includes the light sensor, the
lighting around the exterior mirrors only comes when it is dark.
Note
The time taken for the headlights to go off can be changed in the menu Lights
& Visibility and the function can be switched on or off Ÿpage 70.
Note
When the “Coming home” function is on, if the vehicle door is opened there
is no audible warning signal to advise that the light is still on.
Headlight range control, instrument and switch lighting
Instrument and switch lighting
When the headlights are switched on, the brightness of the instruments and
switch lighting can be regulated to suit your requirements by turning the
switch Ÿfig. 68 .
Headlight range control
The headlight range control Ÿfig. 68 is modified according to the value
of the headlight beam and the vehicle load status. This offers the driver
optimum visibility and the headlights do not dazzle oncoming drivers Ÿ.
The headlights can only be adjusted when the dipped beam is switched on.
To reset, turn switch Ÿfig. 68 :
Dynamic headlight range control
The control is not mounted in vehicles with dynamic headlight range
control. The headlight range is automatically adjusted according to the
vehicle load status when the headlights are switched on.
WARNING
Heavy objects in the vehicle may mean that the headlights dazzle and
distract other drivers. This could result in serious accident.
Fig. 68 Next to the
steering wheel: instru-
ment and switch lighting
control and headlight
range control .
A1A2
ValueVehicle load statusa)
a)If the vehicle load does not correspond to those shown in the table, it is possible to
select intermediary positions.
–Two front occupants, luggage compartment empty
1All seats occupied, luggage compartment empty
2All seats occupied, luggage compartment full. With trailer
and minimum support load
3Driver only, luggage compartment full. With trailer and
maximum support load
A1
A1
A2
A2
A2
A2