bulb Seat Exeo ST 2009 Owner's Guide

If and when
276Changing the side light bulb
The procedure for changing the bulbs on the front
passenger's side is the same as on the driver's side.
– Switch off the ignition and the lights.
– Raise the bonnet.
– Move the brace ⇒ fig. 222 in the direction of the arrow and
remove the rigid cover, separating the brace side and then
removing the two tabs from the other end of the cover.
– Remove the bulb holder by pulling on the grip ⇒fig. 223 (it can
also be removed by pulling on the bulb holder wires).
– Separate the bulb from the bulb holder by pulling both pieces anti-clockwise.
– Fit the new bulb by pressing on the bulb holder.
– Insert the bulb into the socket and press on the bulb holder grip.
– Fit the cover, first inserting the side tabs and then closing the cover and the brace. Make sure that the gasket sits well on the
casing cover during the operation.
– Check whether the new bulb is working.Changing the xenon bulbThe procedure for changing the bulbs on the front passenger's side is the
same as on the driver's side.
WARNING
This type of bulb should be changed at a qualified workshop.
Fig. 222 Side lightFig. 223 Side light
A1
ExeoST_EN.book Seite 276 Donnerstag, 3. September 2009 12:24 12

If and when277
Safety First
Controls and equipment
Practical tips
Technical Data
Changing bulbs for rear lights (in side panel)Overview of rear lightsRear lights in side panel•Brake lights and rear lights•Indicator light
Removing rear light
To change the bulbs you must remove the rear light assembly.
Removing the light requires a certain degree of practical skill.
F ig. 224 O ver vie w of rear
lights
Fig. 225 Luggage
compartment: Location of
the bolt securing the rear
lightFig. 226 Removing rear
light from side panel
ExeoST_EN.book Seite 277 Donnerstag, 3. September 2009 12:24 12

If and when
278
A special retaining screw is used to secure and guide the rear light.
– Check which of the bulbs is defective.
–Open the tailgate.
– Take the screwdriver out of the vehicle's tool kit ⇒ page 251.
– Use the flat-blade side of th e reversible screwdriver insert.
– Prise off the cover with a screwdriver in the slot ⇒page 277,
fig. 225 and remove the cover (with the retaining clips) from
the opening.
– Carefully loosen the screw located behind the cover with the screwdriver, turning it anti-clockwise (arrows) .
– Gradually ease the rear light out of the housing ( ⇒page 277,
fig. 226 positions and ) by pulling alternately in positions
and .
– Remove the bulb holder ⇒page 278.
CautionWhen removing or installing the rear light, take care not to cause any
damage.•Removing the rear light in particular can lead to the paintwork or rear light
becoming damaged. This is another reason why we recommend having the
bulbs changed by a qualified workshop.Note
Make sure you have a soft cloth ready to place under the glass on the rear
light, to avoid any scratches.
Removing the bulb holder
When changing a bulb, you must first remove the bulb holder.There are four securing tabs on the inside of the rear light unit.
– Release the retaining tabs ⇒fig. 227.
– Lift the bulb carrier off in the direction of the arrow .
– Change the defective bulb ⇒page 279.
A1
A2
A3
A4
A1
A2
Fig. 227 Retaining tabs
on reverse side of rear
light
AA
AB
ExeoST_EN.book Seite 278 Donnerstag, 3. September 2009 12:24 12

If and when279
Safety First
Controls and equipment
Practical tips
Technical Data
Changing bulbs
All bulbs can be changed easily in the bulb holder.The bulbs are secured with a bayonet fastener. The table below
gives an overview of the bulb positions.
– Lightly press the defective bulb into the bulb holder, then turn it
to the left and remove it.
– Fit the new bulb, pressing it into the bulb holder and turn it to the
right as far as it will go.
– Use a cloth to remove any fingerp rints from the glass part of the
bulb.
– Check whether the new bulb is working.
– Re-install the bulb holder ⇒page 279.
Position of the bulbsFitting the bulb holder
The bulb holder is easy to fit.– Check that the seal is seated correctly on the bulb holder.
– Position the bulb holder on the rear light and align it so that it is
securely seated.
– Press the bulb holder into the rear light until it engages.
Fig. 228 Position of the
bulbs in the bulb holder:
Example: Outer left rear
light
Pos. ⇒ fig. 228
Bulb function
A
Indicator light
B
Side/stop lights
Fig. 229 Securing the
bulb holder in the rear
light unit
ExeoST_EN.book Seite 279 Donnerstag, 3. September 2009 12:24 12

If and when
280
– Check that all four retaining tabs ⇒page 279, fig. 229 -arrows-
have engaged.
– Re-install the rear light unit ⇒page 280.Fitting the rear light unit
The rear light unit is easy to fit.
– First place the rear light unit in ⇒fig. 230 arrow in the
housing.
– Gently press the rear light unit against the housing, first in posi- tion and then in position , until that the clips engage firmly
in the rubbe r mountings.
– Apply gentle pressure to the front side of the rear light unit and secure using the screwdriver, from the luggage compartment
⇒ fig. 231 .
– Try to move the rear light sideways to ensure it is correctly fitted.
– Fit the cover back onto the screw, with the notch pointing to the rear .
– Put the screwdriver back into the tool kit.
– Make sure that all bulbs for the rear lights are working.
Fig. 230 Fitting the rear
light unit
Fig. 231 Luggage
compartment: Location of
the bolt securing the rear
light unit
A1
A2
A3
A1
A2
ExeoST_EN.book Seite 280 Donnerstag, 3. September 2009 12:24 12

If and when281
Safety First
Controls and equipment
Practical tips
Technical Data
Caution
Take care when fitting the rear light unit to make sure there is no damage to
the paintwork or any of its components.Changing rear light bulbs (in boot lid)Overview of rear lightsRear lights in the boot lid•Rear light•Rear fog light•Reverse light
Removing the bulb holder
The tailgate must be open to change the bulbs.
F ig. 232 O ver vie w of rear
lights
Fig. 233 Remove the
cover of the tailgate trimFig. 234 Remove the bulb
holder
ExeoST_EN.book Seite 281 Donnerstag, 3. September 2009 12:24 12

If and when
282
You can access the bulb holder for the inner rear lights via the inside
of the tailgate.
– Check which of the bulbs is defective.
– Take the screwdriver out of the vehicle's tool kit ⇒ page 251.
– Insert the screwdriver into the opening in the cover ⇒page 281,
fig. 233 and detach the cover .
–Press on the tabs ⇒page 281, fig. 234 in the direction of the
arrows and remove the bulb holder by pulling in the direction of
the arrow .
– Change the bulbs ⇒page 282.Changing bulbs
All bulbs can be changed easily in the bulb holder.
The bulbs are secured with a bayonet fastener. The table below
gives an overview of the bulb positions.
– Lightly press the defective bulb into the bulb holder, then turn it
to the left and remove it.
– Fit the new bulb, pressing it into the bulb holder and turn it to the right as far as it will go.
– Use a cloth to remove any fingerp rints from the glass part of the
bulb.
– Check whether the new bulb is working.
– Re-install the bulb holder ⇒page 282.Position of the bulbsFitting the bulb holder
The bulb holder is easy to fit.– Position the bulb holder on the rear light and align it so that it is
securely seated.
– Press the bulb holder into the rear light until it engages.
– Fit the cover back in the interior trim so that it engages.
A1
A2
AA
AB
Fig. 235 Position of the
bulbs in the bulb holder.
Example: Rear lights in
the tailgate
Pos. ⇒ fig. 235
Bulb function
A
Reverse light
B
Side lights
C
Rear fog light
ExeoST_EN.book Seite 282 Donnerstag, 3. September 2009 12:24 12

If and when283
Safety First
Controls and equipment
Practical tips
Technical Data
– Put the screwdriver back into the tool kit.
– Make sure that all bulbs for the rear lights are working.Side indicators– Press the indicator to the left or to the right to remove the lamp.
– Remove the lamp holder from the indicator.
– Remove the failed glass bulb and replace with a new bulb.
– Insert the lamp holder in the indicator guide until it clicks into
place.
– First place the indicator in th e opening in the bodywork, fixing
the tabs ⇒ fig. 236, arrow . – Insert the bulb as shown by the arrow
⇒fig. 236 .
Luggage compartment lights
Fig. 236 Side indicator
A1
A2
Fig. 237 Luggage
compartment lightFig. 238 Luggage
compartment light
ExeoST_EN.book Seite 283 Donnerstag, 3. September 2009 12:24 12

If and when
284
– Remove the tulip-shaped fitting by pressing on its inside edge using the flat side of a screwdriver.
– Remove the protective cover and remove the bulb from the housing.Registration light
– To remove the tulip-shaped fitting, unscrew the bolts ⇒fig. 239 .
– Remove the bulb, moving it in the direction of the arrow and outwards ⇒fig. 240 .
– Installation is in the reverse order.
Fig. 239 Registration
light
Fig. 240 Registration
light
ExeoST_EN.book Seite 284 Donnerstag, 3. September 2009 12:24 12

If and when285
Safety First
Controls and equipment
Practical tips
Technical Data
Sunroof light– Remove the bulb carefully, using the screwdriver on its flat side
⇒fig. 241 . – Use a screwdriver to remove the protective cover.
– Remove the bulb, moving it in the direction of the arrow and
outwards ⇒fig. 242 .
Jump-startingJump leads
The jump lead must have a su fficient wire cross section.If the engine fails to start because of a discharged battery, the battery can be
connected to the battery of another vehicle to start the engine.
Jump leads
Jump leads must comply with the standard DIN 72553 (see manufacturer's
documentation). The wire cross section must be at least 25 mm
2 for petrol
engines and at least 35 mm
2 for diesel engines.
Note
•The vehicles must not touch each other, otherwise electricity could flow as
soon as the positive terminals are connected.•The discharged battery must be properly connected to the vehicle elec-
trical system.
Fig. 241 Removing sun
visor lightFig. 242 Removing sun
visor light
ExeoST_EN.book Seite 285 Donnerstag, 3. September 2009 12:24 12