display Seat Exeo ST 2010 User Guide

Cockpit67
Safety First
Operating Instructions
Practical Tips
Technical Specifications
The yellow warning
~ lamp remains on if the system is faulty or if
the pressure is too low in at least one tyre. In the event of a system
fault, the letters TPMS are displayed in the centre of the instrument
panel ⇒page 66, fig. 45 . If the tyre pressure drops rapidly,
message ⇒page 66, fig. 46 will be shown on the central display
of the instrument panel. If the pressure loss is more gradual,
message ⇒page 66, fig. 46 will be shown on the central display
of the instrument panel. This message does not show the tyre
affected. Should any of these warnings be displayed:
–Stop the vehicle.
– Check the tyres. Although the warning corresponds to just one tyre, you should also check the others.
– Correct the tyre pressure ⇒page 246.
For more detailed information on the tyre pressure monitoring system, please
refer to ⇒page 245.Cruise control system*

The indicator lamp
 on the instrument panel lights up when the cruise
control system is operating.
Trailer turn signals*

This turn signal lamp flashes when the turn signals are oper-
ating while towing a caravan or trailer.The turn signal lamp
 flashes when the turn signals are operated if a trailer
is correctly coupled to the vehicle.
Where a turn signal bulb does not work, either on the trailer or on the towing
vehicle, the turn signal bulb will not flash.
Anti-lock brake system (ABS)
J
The warning lamp monitors the ABS and the integrated elec-
tronic differential lock (EDL).The warning lamp
J lights up for a few seconds when the ignition is
switched on and while the engine is being started. The lamp goes out again
after the system has run through an automatic test sequence.
There is a fault in the ABS if:
•The warning lamp does not light up when the ignition is switched on•The warning lamp does not go out again after a few seconds•The warning lamp lights up when the vehicle is moving
The vehicle can still brake in the normal way (except that the ABS control func-
tion is out of action). Please take the vehicle to a qualified workshop as soon
as possible. For further information on the ABS, see ⇒ page 192.
If a malfunction should occur in the ABS, the ESP warning lamp will also light
up.
AAAB
ExeoST_EN.book Seite 67 Freitag, 3. September 2010 11:41 11

Cockpit71
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Driver information systemGeneral notes
The driver information system in the instrument panel shows
the status of various on-board systems at a glance.The display for the driver information system is in the centre of the instrument
panel.
The system runs a check on certain components and functions when the igni-
tion is switched on and while the vehicle is moving. The DIS system gives an
audible warning if a fault should occur or if servicing is required, and a red or
yellow warning symbol (in some cases with a corresponding driver message)
appears in the instrument panel display.
The driver is informed on the audio system.
The driver information system includes the following functions:
Note
•If a fault should occur, the display will show a red or yellow warning
symbol. A red warning symbol indicates a serious malfunction ⇒ page 77. A
yellow warning symbol indicates a less serious malfunction ⇒ page 79.
Fig. 47 Cockpit: Digital
instrument panel display
CD player, radio and telephone display*
⇒page 72
Outside temperature display
⇒page 72
Gear indicator*
⇒page 73
Selector lever positions for the 7-speed automatic gear-
box*
⇒page 189
Selector lever positions with multitronic
®*
⇒page 185
Distance to empty
⇒page 73
Door and tailgate warning
⇒page 74
Service indicator
⇒page 74
auto-check control
⇒page 75
Driving tips
⇒page 76
Handbrake warning
⇒page 76
Bulb monitor*
⇒page 82
Onboard computer*
⇒page 85
Tyre pressure monitoring*
⇒page 89
Navigation information*
Separate Instruc-
tion Manual
ExeoST_EN.book Seite 71 Freitag, 3. September 2010 11:41 11

Cockpit
72CD, radio and telephone* displayIf the radio is switched on and no Priority 2 faults are indicated by the auto-
check control, depending on the type of radio fitted, the display will show the
name or frequency of the selected radio station and complementary informa-
tion, once the “OK” symbol has gone out.
When in CD mode*, the display will show the current track.
If you have a compatible telephone*, the phone book or telephone dialled
can also be seen on this display.
These displays appear in addition to the display on the radio itself.
Outside temperature displayThe outside temperature is shown in the display when the ignition is switched
on ⇒fig. 49. In vehicles with an automatic gearbox, the display does not
appear until the driver has engaged a gear.
At temperatures below +5 °C a snowflake symbol appears next to the temper-
ature display. This is to warn the driver to take extra care when there is a risk
of ice on the road. When the vehicle is stationary or travelling at very low
speeds, the temperature displayed may be slightly higher than the actual
ambient temperature as a result of heat coming from the engine.
If the vehicle has an air conditioner and the display is changed over to °F
(degrees Fahrenheit), the outside temperature display automatically changes
over to °F ⇒page 167.
WARNING
Do not rely on the outside temperature display as an ice warning. Please
bear in mind that there may be ice on the roads even at outside tempera-
tures of +5 °C – beware of ice patches.
Fig. 48 Display: addi-
tional radio information
Fig. 49 Display: Outside
temperature display
ExeoST_EN.book Seite 72 Freitag, 3. September 2010 11:41 11

Cockpit73
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Note
When the display shows route guidance instructions from the navigation
system, the outside temperature appears in the second line of the radio
display.Gear display*
This display helps to save fuel.Use the gear display to save fuel. The display ⇒fig. 50 on the instrument
panel recommends that you select the gear indicated by the arrow. It may
also skip a gear, and recommend changing up from 4th gear to 6th gear, for
example.
Note
•The display may not recommend any gear-change while you are acceler-
ating.•If desired, you can have the gear-change display deactivated by an
Authorised Service Centre.Distance to empty
The distance to empty display can help you to plan your trip.The estimated distance to empty is displayed in km. It shows how far the
vehicle can be driven with the amount of fuel left in the tank, assuming the
same style of driving. The distance to empty is displayed in increments of 10
km.
The distance to empty is calculated on the basis of the fuel consumption over
the last 30 kilometres. The distance to empty will increase if you drive in a
more economical manner.
Fig. 50 Gear display
ExeoST_EN.book Seite 73 Freitag, 3. September 2010 11:41 11

Cockpit
74Door and tailgate warningThe door and tailgate warning symbol lights up if one or more of the doors, or
the bonnet or tailgate are not properly closed when the ignition is on. The
symbol also indicates which of these is not properly closed. The display in the
illustration ⇒fig. 51 shows that the driver door is open.
The corresponding part of the pictogram will flash if either the bonnet or tail-
gate are open. The warning symbol goes out when the bonnet, tailgate and
all the doors are closed.
In vehicles with a driver information system and an onboard computer* the
door catches/tailgate warning symbol can be switched off by briefly pressing
one of the control switches for the onboard computer ⇒page 86. However,
the warning symbol will appear again if any of the doors or the bonnet or tail-
gate is opened or closed.
Service indicator
This display reminds the driver when the next routine service
is due.Displaying distance to next service
When you press the service button briefly with the ignition switched on,
the display will show how far the vehicle can be driven before the next service
is due. This check can be carried out with the engine stopped or running up
to 5 km/h. Before the first 500 km and after the ignition cycle, the kilometres
and days before the service inspection are not displayed.
If the service button is pressed before the first 500 km the following indi-
cation appears on screen:
Service in ----- km --- days
This is also valid for vehicles with “LongLife Service Intervals”*.
Fig. 51 Display: Door and
tailgate warning
Fig. 52 Detailed view of
the instrument panel:
Service indicator
A1
A1
ExeoST_EN.book Seite 74 Freitag, 3. September 2010 11:41 11

Cockpit75
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Service reminder
The instrument panel controls the distance travelled every day. It calculates
the average of these distances travelled and activates the service reminder
sufficiently in advance.
The display reverts back to the standard display after about 5 seconds. The
remaining distance to the next service is updated every time the ignition is
switched on, until the service becomes due.
Service due
When a service is due,
SERVICE! will appear in the display immediately after
you switch on the ignition. The display reverts back to the standard display
after about 5 seconds.
Resetting the display
The display is reset by the workshop after the service has been carried out.
The service interval will be set to a LongLife Service (flexible service interval)
or Inspection Service (fixed service interval), depending on which engine oil
is used. It is only possible to reset the display via the instrument panel when
a n o i l cha n ge i s p e r f o r m e d ; i n t h is cas e t h e d is p l a y ca n o n l y b e r e s e t t o a f i xe d
service interval of 15,000 km. Proceed as follows:
•Switch the ignition off.•Press the service button ⇒page 74, fig. 52 and hold while switching
on the ignition. The display will show one of these messages:
Service in ----- km or Service!•Now press and hold the reset button until the display shows
Service in ----- km --- days or Service!
The display switches out of the reset mode if you do not press the reset button
within 5 seconds.Caution
The system cannot calculate the figures for the service interval display if the
battery is disconnected from the vehicle, so no service reminder can be displayed during this time. Please remember that it is essential to service the
vehicle within the established time limits to prevent its deterioration and to
extend its useful life (particularly that of the engine). The period between two
services must never be longer than the time specified in the Maintenance
Programme, even if you only cover a low mileage during this time.
Note
•Do not reset the service indicator between services, otherwise the display
will be incorrect.•The information in the service indicator remains intact if the battery is
disconnected.•The distance to the next service cannot be called up if the system has
detected a Priority 1 fault (red symbol).Auto-check systemIntroductionThe auto-check system checks important components and vehicle systems.
These background checks are run constantly, as long as the ignition is
switched on.
A message is displayed on the instrument panel if a fault should occur or if
any maintenance or repairs are urgently required. This is accompanied by an
audible warning signal. Depending on the priority of the fault, a red or yellow
warning symbol lights up on the display.
The red symbol indicates danger, whereas the yellow one represents a
warning . Additional messages for the driver may be shown with the red or
yellow symbols.
A1
A2
ExeoST_EN.book Seite 75 Freitag, 3. September 2010 11:41 11

Cockpit
76Driver messages
Additional messages for the driver are displayed together
with the warning symbols on the instrument panel.Driver messages and red symbols
If a red warning symbol appears on the display, you can press the
button ⇒fig. 53 to call up an additional driver message.
For example: in the event of an oil pressure malfunction, the oil pressure
symbol
E w il l a p p e a r i n t h e d i s p la y. I f yo u n o w p r e ss t h e b u t t o n , t h e
following message will appear in the display:
Switch off engine, check oil level
The message will disappear from the display after about 5 seconds. If
required, the message can be called up again by briefly pressing the
button. Driver messages and yellow symbols
If a yellow warning symbol appears in the display, it will automatically be
accompanied by the corresponding driver message.
For example, the symbol
 is displayed to indicate that the windscreen
washer fluid level is low. In addition, the following message will appear:
Top up washer fluid
The message will disappear after a few seconds. If required, the message can
be called up again by briefly pressing the button.
Note
•The messages handbrake on and when stationary apply footbrake to
select gear cannot be called up a second time. They will remain in the display
until the handbrake is released or until a gear is selected.Handbrake warning– Release the handbrake.If you drive by mistake with the handbrake still applied, you will hear a
warning buzzer and the display will show the message:
Handbrake on
The handbrake warning switches on after driving for 3 seconds at speeds
above 5 km/h.
Fig. 53 Instrument panel:
CHECK button
CHECK
CHECK
CHECK
CHECK
ExeoST_EN.book Seite 76 Freitag, 3. September 2010 11:41 11

Cockpit77
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Red symbols
A red symbol warns of a danger.–Stop the vehicle.
– Switch the engine off.
– Check the fault. Obtain professional assistance if necessary.
The red symbols are used to indicate a Priority 1 fault (serious malfunction).
A red symbol is accompanied by three warning chimes. The symbols will keep
flashing until the faults are corrected. If several Priority 1 faults are detected
at the same time, the symbols are displayed one after the other for about 2
seconds.Fault in the brake system
H
A fault in the brake system should be repaired as soon as
possible.If the symbol
H flashes in the display, there is a fault in the brake
system. One of the following messages will appear in the display
together with the symbol:
Stop vehicle, check brake fluid and hydraulic fluid levels
Warning! Fault in brake system (ABS) Take vehicle to workshop
–Stop the vehicle.
– Check the brake fluid level ⇒page 240.
If the ABS fails, the ABS warning lamp
J will light up together with the brake
system fault symbol
H ⇒ .
WARNING
•Before opening the bonnet and checking the brake fluid level, observe
the warning information in ⇒ page 229, “Work in the engine compart-
ment”.•If the brake fluid level in the reservoir is too low, this could result in an
accident. Do not drive on! Obtain technical assistance.
H
BRAKES
Fault in brake system
⇒ page 77

COOLANT
Coolant level too low / coolant tem-
perature too high
⇒ page 78
E
OIL
PRESSURE
Engine oil pressure too low
⇒ page 78Fig. 54 Display: Coolant
level warning
ExeoST_EN.book Seite 77 Freitag, 3. September 2010 11:41 11

Cockpit
78•If the brake warning lamp lights up together with the ABS warning
lamp, this can mean that there is a fault in the ABS control function. As a
result, the rear wheels can lock relatively easily when braking. Under
certain circumstances, the rear of the vehicle could suddenly sway from
side to side, with the subsequent dang er of skidding. Drive carefully to the
nearest specialised workshop and have the fault repaired.
Fault in the cooling system

Faults in the cooling system must be repaired immediately.If the
 symbol flashes in the display, this means that either the
coolant temperature is too high or the coolant level is too low. The
following message will appear in the display together with the
symbol:
Switch off engine and check coolant level
– Stop the vehicle.
– Switch the engine off.
– Check the coolant level ⇒page 234.
– Add more coolant if necessary ⇒page 235.
– Wait for the symbol to go out before driving on.
– Obtain professional assistance if necessary.
If the coolant level is correct, the overheating may be caused by a malfunction
of the radiator fan. If the alternator warning lamp lights up as well
⇒page 69, it is possible that
the drive belt has broken.
Caution
Do not drive on if the symbol
v has come on to indicate a fault in the cooling
system, otherwise there is a risk of engine damage.
Engine oil pressure too low
E
If the engine oil pressure is too low the fault must be repaired
immediately.If the
E
symbol flashes in the display, the oil pressure is too low.
The following message will appear in the display together with the
symbol:
Switch off engine, check oil level
– Stop the vehicle.
– Switch the engine off.
– Check the engine oil level ⇒page 232.
– Obtain professional assistance if necessary.
Engine oil level too low
If the engine oil level is too low, add more oil ⇒page 233.
Engine oil level correct
If the
E symbol flashes and the engine oil level is correct, obtain profes-
sional assistance. Do not drive on! Do not continue to run the engine, even at
idle speed .
WARNING (continued)
ExeoST_EN.book Seite 78 Freitag, 3. September 2010 11:41 11

Cockpit
80Yellow symbols are accompanied by one warning buzzer. The function indi-
cated should be checked as soon as possible. If several Priority 2 faults are
detected at the same time, the symbol s are displayed one after the other for
about 2 seconds at a time.Brake light failure

This warning light will appear on the upper part of the display if any of the
brake lights has failed. A text message in the central part of the display indi-
cates which brake light has failed (left or right).Fuel level low

When this symbol
 comes on for the first time, there are about 8 to 10 litres
of fuel left in the tank. You should fill up as soon as possible ⇒page 225.
Engine speed governing
X
Max. engine speed XXXX rpm
There is a fault in the engine management. In addition, the warning lamp
%0#
on the instrument panel will light up. The engine speed will be governed to
the speed displayed in the driver information system. Please ensure that the
engine speed does not exceed the speed shown (for example, when
changing down a gear).
Take the vehicle to a qualified workshop immediately to have the fault
repaired.
Check engine oil level

If the
 symbol lights up, please check the engine oil level as soon as
possible ⇒page 232. Top up the oil at the next opportunity ⇒page 233.
Engine oil sensor defective *

If the

symbol lights up, take the vehicle to a qualified workshop and have
the oil level sensor checked. Until then it is advisable to check the oil level
every time you fill up with fuel ⇒page 232.
Diesel particulate filter obstructed

If the symbol
 lights up, you can contribute towards automatic filter
cleaning by driving in the right manner. To do this, drive about 15 minutes in
4th or 5th gear (automatic gearbox: S gear range) at a speed of 60 km/h, with
the engine running at approximately 2000 rpm. The increase in temperature
will burn off any soot in the filter. When cleaning is successful, the symbol
switches off.
If the symbol  does not turn off, or the three lamps turn on (particulate
filter
, emission control system fault
 and heaters
D), take the vehicle
to a qualified workshop to repair the fault.
For further information on the diesel particulate filter, see ⇒page 199.
WARNING
It is essential that you adjust your speed to suit the weather, road, terrain
and traffic conditions. The recommended driving speed must never lead to
the driver disregarding the traffic regulations.
ExeoST_EN.book Seite 80 Freitag, 3. September 2010 11:41 11